Rekey Door Locks in Devore: Which Doors, Which Locks

Rekey Door Locks in Devore: what to expect

Rekeying makes sense when the lock on a door is still sound and the only problem is who holds a key. It's the wrong fix when the hardware itself is failing. Signs that a particular door's lock should be replaced rather than rekeyed include a knob that wobbles even after its screws are tightened, a latch that sticks halfway, a deadbolt whose bolt is bent or chewed from being forced, and a cylinder so worn that keys wiggle and catch. Builder-grade knobs on the busiest door in the house often reach that point long before the deadbolt above them does. You don't have to choose one approach for the whole house. A common, sensible plan is to rekey door locks that are in good shape and replace only the one or two that aren't, keying the new hardware to the same key so you still carry one. If you're on the fence about a door, we'll show you what we see once the cylinder is out and give you both prices. The decision stays with you.

What we can do on-site

• Knob and lever entry locks. The knob or lever below your deadbolt has its own cylinder, and it's the one people forget most. On most models a small release catch lets the knob slide off, the cylinder comes out of the knob body, and we re-pin it to match the deadbolt. If the latch sticks or the knob wobbles, we'll point it out before spending your money on it.
• Garage entry and garage side doors. The door between the garage and the house matters more than people think. Many households leave the overhead door up while they're in the yard or driveway, which makes that inner door a front door in practice. We rekey its knob and deadbolt to the house key and check that the door still closes and latches on its own.
• Patio sliders and French doors. If your slider has never had a working key, you're in good company. Plenty of patio door cylinders in Devore were never keyed in the first place, or the key disappeared years ago. We'll tell you whether that lock can be put on a key, and if it can't, how to keep the door secure with an inside lock and a charley bar.
• Security screen and storm doors. A screen door key on its own ring is a daily nuisance. When we rekey door locks behind a security screen, we try to bring the screen onto the same key, so you aren't sorting keys on the porch with groceries in your arms. Where that isn't possible, we can cut its key on a colored blank so it's easy to grab.
• Kwikset SmartKey locks. Matching SmartKey locks to your other doors is simple when everything in the house is Kwikset, since they share a keyway. The challenge is a house with SmartKey on some doors and Schlage on others. We can key the Kwikset doors together and replace the odd ones out, or swap hardware so a single key covers everything.

Local factors in Devore

Older homes in Devore often have a front door lock older than anyone living there: a mortise lock with a painted-over set screw, a rim lock on the back door, or knobs in keyways that few shops still stock blanks for. Most of these can be re-pinned if the lock body is sound. Where a part is obsolete, we'll offer a replacement cylinder or modern hardware keyed to match, and explain plainly why that door needs it.

Foothill homes take a beating from wind, dust and big temperature swings, and doors facing canyon winds tend to slam and drift out of alignment. When we rekey door locks up here, we pay close attention to strike position and weatherstrip pressure, because a bolt fighting a wind-loaded door wears quickly. Clearing fine grit out of each cylinder during the re-pin makes a noticeable difference after a Santa Ana season.

Inland summer heat is hard on doors and locks. Doors facing south or west expand, dark-painted doors get hot enough to make hardware stiff, and old lubricant dries into grit. When we rekey door locks in hot areas, we clean each cylinder thoroughly, use a dry lubricant that won't gum up, and check that the bolt still throws when the door is warm, not just in the cool morning.

Example situations

• Imagine a 1950s bungalow with its original mortise lock on a solid wood front door. The set screw is hidden under several coats of paint, and the cylinder may never have been out of the door. We'd score the paint, back the screw out, and unthread the cylinder slowly so the threads in the lock body survive. The re-pinned cylinder goes back in with a light shot of dry lubricant.
• Say the front door wears a Schlage Encode while the back and garage doors still have their original Kwikset knobs and deadbolts. The owner wants one key. Because the brands use different keyways, we'd re-pin the Encode's Schlage cylinder, replace the Kwikset hardware on the other doors with Schlage keyed to match, and then reset the Encode's codes and app users as a separate step.
• Consider a back door deadbolt that only throws if you pull the door toward you first. The owner has done that for years and figures a rekey will cure it. With the cylinder out, though, the bolt still binds against the strike, which proves the lock isn't the problem. The fix is a strike adjustment and longer screws during the same visit, and afterward the new key turns with a fingertip.
• A typical call: a family on a cul-de-sac near Glen Helen Amphitheater gave the side garage door key to a dog walker last spring and never got it back. Every other door is fine. Because that garage door was keyed alike with the front, rekeying it alone would mean carrying a second key. We'd lay out both choices, then either set the garage door to its own key or move all three doors to a fresh one.

How the visit works

1. Tell us which doors and what's on them. Call (951) 903-3193 and list the doors you want rekeyed: front, back, garage entry, side door, slider, screen, gate. Tell us the brand if you can read it on the latch face or a key head. Kwikset, Schlage and other makers take different parts, so the more we know, the better stocked we arrive.
2. Confirm you're authorized. Verification protects you more than it protects us. The same rule that has you showing ID also stops a stranger from having your locks rekeyed while you're at work. It takes a minute, and we do it every time, including for a single-door job on a quiet afternoon.
3. Check each door before touching the lock. We look at the strike plate, hinge screws, latch alignment and the gap around the door. A door that has dropped a little on its hinges drags the bolt across the strike, and no amount of re-pinning cures that. We point out anything we'd adjust and add it to the quote as a separate line.
4. Re-pin each cylinder, one door at a time. We work one door at a time so the house stays secure. The cylinder comes out, the plug is pushed out with a follower so the springs and driver pins stay put, and new key pins are set to the new key's cuts. Old pins are discarded, not reused.
5. Test from both sides. Each rekeyed lock is tested with the door open and again with it closed, from outside with the key and inside with the thumbturn. We also try one of your old keys to confirm it no longer turns. Only then does the next door come apart.
6. Hand over keys and a door list. You get the agreed number of keys, and we suggest counting them in front of us. We also leave a simple list of which doors take which key, useful later when a cleaner, contractor or relative asks for access and you need to decide what to hand over.

What affects the cost

• What kind of hardware each door has. Standard deadbolts, knobs and levers are the quickest to rekey. Mortise locks, handlesets with two keyed functions, euro cylinders on multipoint doors and retrofit smart locks take longer to reach, and some need a replacement cylinder rather than a re-pin. Each of those is priced on its own line.
• Brands and keyways. High-security cylinders such as Medeco, Mul-T-Lock or ASSA often use restricted keyways with controlled key blanks. Rekeying those may require parts or keys sourced through an authorized dealer, which affects both price and timing. We'll tell you up front if any of your locks fall into that group.
• Whether you have working keys. If a door has sat unlocked or unused for years because its key is gone, mention it when you call. We can usually open and re-pin it, but we price that door separately so you can decide whether getting it back on a key is worth it to you.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Devore.

Practical tips before you call

• Before calling, walk the house and count keyholes instead of doors. A front entry may have two, a handleset one, the garage entry two, the security screen one. Jot the brand from each latch face or key head beside it. That short list gets you a phone quote that holds up once we're standing at your door in Devore.
• Decide which doors truly need the same key. One key for the front, back and garage entry is convenient. A separate key for an ADU, a home office or a storage room may be smarter. It's far easier to plan that before we start than to re-pin doors a second time.
• Hold on to the key code or the first key we cut. Copies made from copies drift a little each time, and eventually a duplicate won't turn smoothly. A key cut to the code is accurate, so treat it as your master copy and make future duplicates from it.
• Hand new keys to fewer people than before. A rekey is a reset; if the same five people end up with copies, you've changed the key but not who can get in. For occasional helpers, a smart lock code you can delete later is often better than another metal key.

Mistakes to avoid

• Lubricating with oil or grease. A shot of household oil seems to help for a week, then the film gathers dust and the pins start to drag. Locksmiths use dry graphite or a PTFE lock lubricant, applied sparingly. Inside a cylinder, more lubricant is never better.
• Rekeying only the deadbolt and forgetting the knob. Many front doors have two keyed cylinders, and if the knob still takes the old key, anyone holding it can walk in whenever the deadbolt isn't thrown. Rekey both, or swap the knob for a passage set with no keyhole at all.
• Buying a DIY rekey kit for the wrong brand. Kits are keyway-specific, and the pins, springs and follower in a Kwikset kit won't help with a Schlage cylinder. Even with the right kit, one slipped follower can launch drivers and springs across the floor and leave the door unusable.

Service in Devore

Devore is about 8 miles from our San Bernardino base, roughly 14 minutes in light traffic via Kendall Drive or Palm Avenue to I-215 North, through the Devore junction onto I-15 North, exit Kenwood Avenue for Devore Heights. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Stuck on the shoulder or in a parking lot along Cajon Boulevard? Get somewhere safe, turn on your hazards, and give us the nearest exit or business so we can find the car without guessing.

About Devore: Devore is named for John A. Devore, who arrived in Southern California in 1901 to work for the Kenwood Corporation; the area was briefly known as Kenwood Heights around 1903.

Planning a rekey in Devore?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.