Rekey Door Locks in San Bernardino, One Door or Every Door

Rekey Door Locks in San Bernardino: what to expect

A fresh set of pins can't fix a door that fights its own lock. Doors move: wood swells during winter rains and shrinks again in dry heat, hinge screws loosen, and houses settle, so a strike plate that lined up perfectly when the lock went in may now sit a little high or low. The result is a deadbolt you have to push, pull or lift to throw, and that sideways pressure wears the cylinder, tailpiece and bolt far faster than normal use. So when we rekey door locks, we check each door's operation before and after. We look for full bolt throw, a latch that catches without a slam, hinge screws that bite, and a strike held by long screws reaching the framing. The door from the garage into the house deserves special attention. In many California homes it has spring hinges or a closer so it shuts and latches on its own, and a freshly rekeyed lock does little good if that door drifts open. Small adjustments made during the same visit usually settle these problems for good.

How we can help in San Bernardino

• Handlesets and gripsets. Handlesets often carry a premium finish such as oil-rubbed bronze, satin nickel or polished brass, and they're expensive to replace. Rekeying keeps that finish on the door. We work carefully around the escutcheons, use the right drivers for the decorative screws and wipe down every surface we've touched before packing up.
• Mortise and rim cylinders. Rim cylinders are the flat-faced cylinders on surface-mounted deadlocks, older back doors and many gate locks. Two long screws inside hold the cylinder, and a flat tailpiece reaches into the lock case. They rekey like any pin tumbler cylinder; we just confirm the tailpiece length suits the door's thickness before reinstalling it.
• Security screen and storm doors. Storm doors use lighter latch hardware with a small keyed handle, often a wafer lock that can't be re-pinned. If the storm door needs to be on your key, we look for a keyed replacement handle that fits the door's hole pattern. If not, many owners simply leave the storm door unkeyed and rely on the entry door behind it.
• Smart lock backup cylinders. Retrofit smart locks such as August and Level work differently. They mount over or inside your existing deadbolt, which keeps its original cylinder. Rekeying that cylinder is like any other deadbolt, though the smart hardware has to come off first. We remove it carefully, re-pin the cylinder and confirm the motor still throws the bolt all the way.
• Matching a door to the key you already carry. Bringing a stray door onto your key works best when your existing key is in decent shape. A key copied from a copy may have rounded cuts, and pinning a lock to those worn cuts bakes in the error. In that case we cut a fresh key to the original code and pin the door to that key instead.

Local factors in San Bernardino

Foothill homes take a beating from wind, dust and big temperature swings, and doors facing canyon winds tend to slam and drift out of alignment. When we rekey door locks up here, we pay close attention to strike position and weatherstrip pressure, because a bolt fighting a wind-loaded door wears quickly. Clearing fine grit out of each cylinder during the re-pin makes a noticeable difference after a Santa Ana season.

Inland summer heat is hard on doors and locks. Doors facing south or west expand, dark-painted doors get hot enough to make hardware stiff, and old lubricant dries into grit. When we rekey door locks in hot areas, we clean each cylinder thoroughly, use a dry lubricant that won't gum up, and check that the bolt still throws when the door is warm, not just in the cool morning.

Older homes in San Bernardino often have a front door lock older than anyone living there: a mortise lock with a painted-over set screw, a rim lock on the back door, or knobs in keyways that few shops still stock blanks for. Most of these can be re-pinned if the lock body is sound. Where a part is obsolete, we'll offer a replacement cylinder or modern hardware keyed to match, and explain plainly why that door needs it.

Common situations

• For example, a homeowner off Base Line Street asks us to rekey door locks including the patio slider, whose key went missing years ago. On inspection, the slider's cylinder is a wafer design that can't be re-pinned. Rather than charging for a pointless attempt, we'd show them why, then offer a keyed replacement that fits the slider's cutout or a sturdy foot lock that secures it from inside.
• A typical ADU setup: a converted garage behind a house in San Bernardino now has its own entry door with a lever and a deadbolt. The owners rent it to a relative and want their house key to open it, but they don't want the ADU key opening the main house. We'd explain a small master key arrangement, pin the ADU door accordingly, and write down which keys go to whom.
• A typical evening call in San Bernardino: the door from the garage into the kitchen won't latch unless someone slams it. The owner wanted that lock rekeyed after a house sitter left and assumed the knob was failing. It isn't. The spring hinges have lost tension and the strike sits slightly high. We'd re-pin the knob and deadbolt, tension the hinges and reset the strike, and the door closes on its own again.
• Imagine a 1950s bungalow with its original mortise lock on a solid wood front door. The set screw is hidden under several coats of paint, and the cylinder may never have been out of the door. We'd score the paint, back the screw out, and unthread the cylinder slowly so the threads in the lock body survive. The re-pinned cylinder goes back in with a light shot of dry lubricant.

How the visit works

1. Tell us which doors and what's on them. Call (951) 903-3193 and list the doors you want rekeyed: front, back, garage entry, side door, slider, screen, gate. Tell us the brand if you can read it on the latch face or a key head. Kwikset, Schlage and other makers take different parts, so the more we know, the better stocked we arrive.
2. Confirm you're authorized. Renters, property managers and relatives house-sitting each need slightly different proof. A tenant may need the landlord's written permission, depending on the lease. A manager shows written authorization from the owner. If you're unsure what counts, ask when you call, and we'll tell you exactly what to have ready.
3. Check each door before touching the lock. We look at the strike plate, hinge screws, latch alignment and the gap around the door. A door that has dropped a little on its hinges drags the bolt across the strike, and no amount of re-pinning cures that. We point out anything we'd adjust and add it to the quote as a separate line.
4. Re-pin each cylinder, one door at a time. For doors keyed to match, we pin every cylinder to the same bitting from a single key code. For doors that need a separate key, we choose a code with no near-matching cuts, so one key can't accidentally turn the other door's lock.
5. Test from both sides. Each rekeyed lock is tested with the door open and again with it closed, from outside with the key and inside with the thumbturn. We also try one of your old keys to confirm it no longer turns. Only then does the next door come apart.
6. Hand over keys and a door list. You get the agreed number of keys, and we suggest counting them in front of us. We also leave a simple list of which doors take which key, useful later when a cleaner, contractor or relative asks for access and you need to decide what to hand over.

What affects the cost

• What kind of hardware each door has. Labor rises with how a cylinder is mounted, not with how expensive the lock looks. A plain Kwikset deadbolt and a polished Baldwin deadbolt re-pin in much the same way, but a painted-in mortise cylinder or a smart lock that has to be unmounted first takes noticeably more time.
• Brands and keyways. Some keyways are easier to stock than others. Kwikset KW1 and Schlage SC1 are everywhere, while older brands, imported hardware or six-pin cylinders may need specific pins or blanks. We carry broad stock, but a rare keyway can mean a return trip, which we'd flag before starting.
• Door adjustments and small parts. Adjusting a strike plate, adding longer screws or tightening loose hinges adds a little time and occasionally a part, such as a reinforced strike. These fixes often matter as much as the rekey itself, because a door that binds will wear out a freshly pinned cylinder.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in San Bernardino.

Advice before you book

• Plan around our hours: every day from 6:30 a.m. to 11:30 p.m. We're closed overnight. An early weekday slot before work suits many households in San Bernardino, and a Sunday visit works well when several doors are on the list.
• Before calling, walk the house and count keyholes instead of doors. A front entry may have two, a handleset one, the garage entry two, the security screen one. Jot the brand from each latch face or key head beside it. That short list gets you a phone quote that holds up once we're standing at your door in San Bernardino.
• Pay attention to how the garage-to-house door closes while we're there. If it doesn't close and latch on its own, mention it. A properly tensioned spring hinge or closer keeps that door secure without anyone having to remember to pull it shut on the way out.
• Hold on to the key code or the first key we cut. Copies made from copies drift a little each time, and eventually a duplicate won't turn smoothly. A key cut to the code is accurate, so treat it as your master copy and make future duplicates from it.

What not to do

• Rekeying only the deadbolt and forgetting the knob. Many front doors have two keyed cylinders, and if the knob still takes the old key, anyone holding it can walk in whenever the deadbolt isn't thrown. Rekey both, or swap the knob for a passage set with no keyhole at all.
• Buying a DIY rekey kit for the wrong brand. Kits are keyway-specific, and the pins, springs and follower in a Kwikset kit won't help with a Schlage cylinder. Even with the right kit, one slipped follower can launch drivers and springs across the floor and leave the door unusable.
• Lubricating with oil or grease. A shot of household oil seems to help for a week, then the film gathers dust and the pins start to drag. Locksmiths use dry graphite or a PTFE lock lubricant, applied sparingly. Inside a cylinder, more lubricant is never better.

Reaching San Bernardino

San Bernardino is our home base, so most addresses in town are a short drive. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Once the evening commute thins out on SR-259, drive times usually shrink. That makes an evening call before closing a practical option for non-urgent jobs that you couldn't fit into the workday.

About San Bernardino: Norton Air Force Base operated on the city's east side from 1942 until 1994, and the site is now San Bernardino International Airport and a large logistics district.

Planning a rekey in San Bernardino?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.