Car key replacement by make, model and year

The key types we replace

• Basic mechanical key. A plain mechanical key has no chip and no electronics, just a cut blade that lines up the wafers inside the lock. If your vehicle uses one, replacement is mostly a cutting job, but how it's cut matters. Copying a worn key copies its wear, and a duplicate of a duplicate drifts further from spec each time. We prefer to cut by code: we look up or decode the factory bitting, then cut a fresh key to the original depths on a code machine. The result turns smoothly in the doors and ignition instead of needing a jiggle. If the ignition wafers themselves are already worn, we'll point that out too.
• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your vehicle, we'll explain which method fits and why.
• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your vehicle, we open the old key and show you what's broken before recommending anything.
• Key with separate remote fob. Separate remotes are easy to find online, which is exactly why they cause trouble. A listing can show the same shell as your vehicle remote while hiding a different FCC ID, frequency or internal chip, and some used remotes are locked to the first vehicle they were paired with. We're glad to look at one you've already bought, and we'll tell you honestly whether it can be paired before charging you to try. If the remote side of your setup has become unreliable, it's also worth asking whether a fresh remote and a newly cut key, matched together, would cost less than chasing repairs on aging parts.
• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a vehicle, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your vehicle and which we don't.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your vehicle , we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.
• Key card. Adding a key card to a vehicle is usually done inside the vehicle's own menus, and the car typically asks for an already-authorized key, card or phone to approve the new one. That's a deliberate security choice by the manufacturer, and it shapes what any locksmith can do. If you still have a working key, we can walk you through pairing a new card and help if you end up locked out. If every authorized key is gone, the manufacturer's service center generally has to restore access, and we'll tell you so plainly rather than charge for a visit that can't solve the problem. That honesty saves you a wasted afternoon.
• Phone as key. Phone keys fail in ordinary ways: a dead battery, an app that logs you out after an update, Bluetooth switched off, or a new phone that hasn't been set up yet. That's why every vehicle with a phone key, including a vehicle, should have a working physical backup, whether that's a key card, a fob or a keypad code. Some phones keep a power reserve that lets the wallet key work for a while after the screen goes dark, but don't count on it in a parking garage. Where your platform allows a locksmith to program a backup fob or card, we can do that on-site; where it doesn't, we'll explain the dealer path.

How the job works

1. Identify the exact key your vehicle uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two vehicle keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your vehicle and your schedule.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.