One Key for Every Door: Same Key for All House Locks in Devore

What to know first in Devore

Every pin tumbler lock in your house has a plug that turns only when the pins inside it line up at the shear line. Each key's cuts lift a stack of key pins and driver pins to exactly that line. To give you the same key for all house locks, a locksmith removes each plug, dumps the old key pins, and loads new ones whose lengths match the cuts on one chosen key. Springs and driver pins usually stay, although we replace tired springs and corroded pins as we go. Five-pin residential cylinders such as Kwikset KW1 and Schlage SC1 take only a few minutes each once the lock is off the door; handlesets, mortise cylinders and smart deadbolts take longer because there's more to disassemble. The new combination comes from a key we cut by code, not from copying one of your old keys, so wear doesn't carry forward. When every cylinder is back on the door, we test each one with every new copy, from outside and inside, with the door open and then closed against the strike. Your previous keys stop working at all of those doors at once.

What we can do on-site

• Rekeying same-brand locks to one key. Same-brand houses are the easy case. A home fitted throughout with Kwikset, or throughout with Schlage, can usually be brought to one key using only pins, springs and a code-cut key. No hardware gets replaced, the trim stays as it is, and the visit mostly consists of disassembly, re-pinning and careful testing at each door.
• Smart locks and keypads on the house key. Keypad and app locks still have a key cylinder for dead batteries, and that cylinder can usually share your house key. Kwikset's Halo and SmartCode models use SmartKey on the KW1 keyway; Schlage's Encode and Connect models take a Schlage C cylinder. We re-pin or reset that backup cylinder so the emergency key matches everything else.
• Matching new hardware to your existing key. Once the house runs on one key, a new deadbolt or replacement knob doesn't have to break the system. Buy hardware in the same brand and keyway, or let us supply it, and we key the new cylinder to your existing combination during installation. You won't need a second key, and the pattern stays intact.
• Fixing worn or sticky locks along the way. There's no point matching a lock that fights its key. While each cylinder is apart, we check pins for wear, springs for fatigue and the plug for grit. Worn parts get replaced, the cylinder gets a dry lubricant, and a lock that was sticky before turns cleanly with the new key.
• Two-key and master key options. Sometimes one key for everything isn't the right fit. A casita, home office or garage apartment may need its own key while you keep one that opens all. A small residential master key arrangement can do that, though it takes extra planning and isn't possible on every lock. Kwikset SmartKey cylinders, for example, can't be master keyed.

How Devore shapes the job

Older homes in Devore often carry decades of hardware layers: an original knob, a deadbolt added later, a mortise lock on the front door, maybe a rim night latch nobody uses anymore. Getting one key for that mix starts with sorting what can be rekeyed, what accepts a standard cylinder and what has to be replaced. Original mortise bodies are often worth keeping, because many accept a modern threaded cylinder in your house keyway.

On larger lots with workshops, barns, pump houses and equipment gates, the number of keys multiplies fast. Rekeyable padlocks and door locks in the same keyway as the house can bring them onto one key, but think about whether ranch hands or neighbors need yard access without house access. A two-key plan, one for the house and one for outbuildings, often suits rural properties better.

If you leave before dawn and return after dark, fumbling through keys at an unlit door is a daily annoyance. One key for every door lets you lock the back door, the garage entry and the front in seconds. Since our hours start at 6:30 a.m. every day, we can often schedule the rekey before you head out on Palm Avenue or as you get home.

Example situations

• Picture a grandmother who's started having trouble telling her keys apart, especially at dusk. Her family asks for one key across the house. We'd rekey the front, back and garage doors to match, cut a key with a large rubber head that's easy to grip, and check that each deadbolt turns with light pressure, adjusting a strike that had been forcing her to shove the door.
• A typical call: the front door has a Schlage deadbolt and handleset, the back door a Kwikset knob and deadbolt left from an old repair, and the garage entry a Schlage knob. The owner wants one key. Since three of the five cylinders are already Schlage, we'd rekey those, replace the two Kwikset pieces with Schlage hardware, and set everything to one fresh combination.
• Say a homeowner installed a Schlage Encode on the front door last year and still carries an old Kwikset key for the back door and garage. Because the Encode takes a Schlage cylinder, the fix would be swapping the two Kwikset locks for Schlage hardware and keying them, plus the Encode's backup cylinder, to one key, so a dead battery never sends anyone hunting for a different key.
• For example, a remodel leaves a Devore home with a handsome new front door and a designer handleset still keyed to its factory combination, while the rest of the house runs on one Kwikset key. If the handleset accepts a KW1 cylinder, we'd swap or re-pin it to match; if it uses its own keyway, we'd check whether a compatible cylinder is available before suggesting anything else.

Step by step with Julian's Locksmith

1. Send photos and a count of your locks. Tell us what's on the ring now: how many different keys, which doors they open, and whether any lock has no key at all. That last detail matters, since a lock without a working key needs picking or decoding before it can be rekeyed with the others.
2. Gather a working key for each lock. Before we arrive, find a key that opens each lock, even if it's a worn copy. With a working key, the plug comes out in moments. Without one, we pick or otherwise open the cylinder first, which adds time but is usually still cheaper than replacing the lock.
3. Verify ownership and confirm the plan. Rekeying changes who can get into a house, so we confirm identity and residence first. Renters should have the landlord's permission in hand. Once that's settled, we go door to door, agree on which locks join the one-key plan, and quote the total.
4. Pick the new key combination. We generate a fresh combination for your house rather than reusing any old key, so nobody who held a previous copy can open anything. The cuts are checked against the maker's maximum adjacent cut specification, which keeps neighboring depths close enough for the key to slide in and out smoothly.
5. Rekey and reinstall each cylinder. Door by door, we remove the cylinder, slide the plug out with a follower, replace the key pins to fit the new key and add fresh springs where needed. Each cylinder is tested on the bench before it goes back in, then again once it's mounted on the door.
6. Test every door and hand over the keys. Before we leave, you try the key yourself at every door. If anything feels stiff, we fix it then and there. We note the brand and keyway on your invoice so future locks can be bought to match, and we take the old pins away with us.

Pricing factors

• How many cylinders you're matching. Each lock you add to the one-key plan adds a little labor and a set of pins. Small homes with three or four locks are quick; larger homes with outbuildings take longer. If budget is tight, start with exterior doors and the garage entry, then add the shed or gate later, keyed to the same combination.
• Smart lock and high-security cylinders. Smart locks take longer to rekey because the interior unit, cables and sometimes the whole lock come off the door before the cylinder can be reached. That extra labor shows up in the quote. Retrofit units mounted over an existing deadbolt add little, since the cylinder underneath is an ordinary one.
• Number of key copies. With one key for everything, it's tempting to hand copies to everyone who might ever need one. Every extra copy adds a little to the bill and a little to your exposure. We'll cut what you ask for, but most families are better served by fewer keys and a clear record of who holds them.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Devore.

What to do before we arrive

• Look at the head of each key. Most residential keys carry the brand name or a blank code such as KW1 or SC1. If every key on your ring says the same thing, getting one key for the whole house will probably be a straightforward rekey without any new hardware.
• Use a dry lubricant made for locks, such as a graphite or PTFE product, once or twice a year. Oil-based sprays attract dust and gum up pins over time, especially in hot, dusty inland summers, and a sticky cylinder is the first thing that makes a one-key setup feel unreliable.
• Consider giving workers a code instead of a key. A keypad deadbolt on a side or garage door lets a cleaner, pet sitter or contractor in without handing over the one key that opens everything, and you can delete the code the day the job ends.
• Don't forget the door between the garage and the house. People rekey the front door and overlook the one entry that a stolen garage remote can lead straight to. If the garage entry has only a knob, ask about adding a deadbolt keyed to the same key while we're there.

Mistakes to avoid

• Rekeying most of the doors but skipping one, often the garage side door or a back door nobody uses. That forgotten lock still opens with an old key, which defeats the security reason for rekeying and keeps a second key on your ring.
• Forcing a SmartKey reset with the wrong tool or without a working key. The SmartKey process only works when the current key turns the cylinder properly. Forcing it can jam the sliders and leave the lock unusable until a locksmith resets or replaces it.
• Filing or grinding a key so it fits a lock with a different keyway. A modified key can get stuck or snap inside the cylinder, and it still won't operate the lock reliably. A different keyway needs a different cylinder, not a reshaped key.

Service in Devore

Devore is about 8 miles from our San Bernardino base, roughly 14 minutes in light traffic via Kendall Drive or Palm Avenue to I-215 North, through the Devore junction onto I-15 North, exit Kenwood Avenue for Devore Heights. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Rush hour on Devore Road can stretch a drive considerably. We'd rather give you a realistic arrival window than an optimistic one, and we'll call you if a closure or a crash changes the plan.

About Devore: A two-story Santa Fe depot served Devore as a railroad station from 1908 to 1930 and was demolished around 1958.

Planning a rekey in Devore?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.