2018 Chevrolet Impala Key Replacement

2018 Impala key specs

The 2014-2020 Impala came two ways. Cars with a key slot use an HU100 flip key with a Philips 46 extended transponder and four or five buttons. Cars with keyless access and push-button start use a proximity fob that looks similar but is a different part, listed under FCC ID OHT05918179. Check the dash before ordering. A 2014-2016 Impala Limited is the previous body and takes the ninth-generation B111 Circle Plus key instead.

What's specific to the 2018 Impala

The 2018 Chevrolet Impala is the fifth of 7 model years in the Impala Tenth generation (Epsilon II) (2014–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 8 years old, a 2018 Chevrolet Impala has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2018 Chevrolet Impala

• Flip (switchblade) key. A flip key folds its blade into the fob on a spring-loaded hinge and swings it out with the press of a button. Inside the body sit the transponder chip and the remote circuit board, which means the metal blade itself carries no electronics. That's good news when the blade snaps. On many flip keys for a Chevrolet Impala, we can cut a new blade to your key code and fit it into your existing fob, with no reprogramming required, because the chip and remote never left the housing. Many flip-key blades are laser-cut, with a groove milled along the side rather than notches on the edge, so they need a code machine built for that profile.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2018 Chevrolet Impala open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Chevrolet immobilizer works on the Impala

• The turn-key flip remote, FCC ID OHT01060512, is shared with the 2010-2015 Camaro, 2011-2015 Cruze and 2013-2016 Malibu.
• Keyless-access Impalas use a proximity fob listed under OHT05918179, which will not work in a key-slot car.
• If your registration reads Impala Limited, the car is the older 2006-2013 design and uses that generation's key.

Programming a 2018 Impala key

Flip keys are cut on a laser machine and programmed over OBD-II, and GM's on-board add works when you already have two recognized keys. Proximity fobs are registered with a programmer and have no on-board option. For all-keys-lost, the programmer registers new keys on either version, and some flip-key cars also accept GM's 30-minute relearn. The emergency blade in a proximity fob is cut to the door lock.

Lost every key to your Impala?

When every key is gone, the route depends on the system. On Passlock and PASS-Key II vehicles we cut a new key from the code or by decoding a lock, add the right resistor pellet where needed, and the vehicle starts with no programming. Circle Plus and HU100 transponder vehicles get a freshly cut key programmed over OBD-II, and GM's own 30-minute relearn also works on many of them, erasing the lost keys in the process. Proximity-fob models need a new fob, an emergency blade cut to the locks and a programmer, often with a long security wait. Global B models and the electric Blazer EV and Equinox EV may need online authorization or the dealer, and we tell you which before starting. Expect to show ID and proof of ownership first.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Impala and your schedule.

Impala key battery

Most fobs for a 2018 Chevrolet Impala open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Impala uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chevrolet Impala keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Impala, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Impala key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Chevrolet Impala is the most involved of all, both in the part itself and in the programming.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Chevrolet system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chevrolet key problems

• On trucks, vans and sedans with a separate remote, the remote cannot start the engine. A new fob fixes the locks, but a no-start with a security message is a key or immobilizer problem, which owners often misread as a remote failure.
• Push-button Chevrolets show a remote-not-detected style message when the fob battery runs low. The owner's manual shows a backup spot, usually in the console or cupholder area, where a weak fob can still be read to start the vehicle.
• A flashing security light with a crank-no-start, or an engine that dies after a few seconds, is the classic Passlock fault on 2000-2005 Impalas, Cavaliers, S-10 Blazers and first-generation Avalanches. The cylinder sensor or its wiring is usually to blame, not the key.
• Global B models such as the 2023 and newer Colorado, the 2025 and newer Equinox and the C8 Corvette use a CR2450 fob battery rather than the CR2032 found in earlier Chevy fobs. The two cells are not interchangeable, so check before buying.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2018 Chevrolet Impala key?

Need a key for your 2018 Chevrolet Impala? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.