2016 Chevrolet Impala Key Replacement

2016 Impala key specs

The 2014-2020 Impala came two ways. Cars with a key slot use an HU100 flip key with a Philips 46 extended transponder and four or five buttons. Cars with keyless access and push-button start use a proximity fob that looks similar but is a different part, listed under FCC ID OHT05918179. Check the dash before ordering. A 2014-2016 Impala Limited is the previous body and takes the ninth-generation B111 Circle Plus key instead.

What's specific to the 2016 Impala

The 2016 Chevrolet Impala is the third of 7 model years in the Impala Tenth generation (Epsilon II) (2014–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 10 years old, a 2016 Chevrolet Impala has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2016 Impala can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2016 Chevrolet Impala

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Chevrolet Impala, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2016 Impala and which we don't.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Chevrolet Impala Tenth generation (Epsilon II), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Chevrolet immobilizer works on the Impala

Chevrolet key systems since 2000 fall into a handful of families, and the model year usually tells us which one a car or truck carries. The 2000-2002 Camaro still used PASS-Key II, where a resistor pellet in the key blade was the only electronic check. Most trucks, vans and many cars of that period, including the Cavalier, the 2000-2005 Impala, the S-10 Blazer and the first Avalanche, used Passlock instead: the sensor sits in the ignition cylinder and the key holds no chip. The C5 Corvette was an early PASS-Key 3 car with a transponder in the key head. From about 2006, Circle Plus keys carrying a Philips 46 chip spread across the lineup, from the Cobalt and Impala to the Avalanche and Express. The 2010s brought HU100 laser-cut blades and flip keys, then proximity fobs with push-button start. Starting with the 2020 Corvette, newer models moved to GM's Global B electrical architecture, where key programming needs online authorization, and the Blazer EV and Equinox EV use it too. Two outliers follow their builders: the Korean-engineered Aveo and the Nissan-built City Express.

• The turn-key flip remote, FCC ID OHT01060512, is shared with the 2010-2015 Camaro, 2011-2015 Cruze and 2013-2016 Malibu.
• Keyless-access Impalas use a proximity fob listed under OHT05918179, which will not work in a key-slot car.
• If your registration reads Impala Limited, the car is the older 2006-2013 design and uses that generation's key.

Programming a 2016 Impala key

Flip keys are cut on a laser machine and programmed over OBD-II, and GM's on-board add works when you already have two recognized keys. Proximity fobs are registered with a programmer and have no on-board option. For all-keys-lost, the programmer registers new keys on either version, and some flip-key cars also accept GM's 30-minute relearn. The emergency blade in a proximity fob is cut to the door lock.

Lost every key to your Impala?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Chevrolet Impala can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Chevrolet Impala requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Chevrolet Impala, ask us directly and you'll get a plain answer.

Impala key battery

Most fobs for a 2016 Chevrolet Impala open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Impala uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chevrolet Impala keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chevrolet keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Impala, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Impala key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Impala came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chevrolet key problems

• Used fobs bought online are frequently locked to another vehicle. Some Global A fobs can be unlocked or reflashed before programming, but many newer GM fobs cannot be reused at all, so ask us before ordering one.
• Flip keys on the Camaro, Cruze, Equinox and Impala tend to break at the hinge, leaving the blade floppy or unable to lock open. The transponder and circuit board usually survive, so a new shell often avoids programming a whole new key.
• On trucks, vans and sedans with a separate remote, the remote cannot start the engine. A new fob fixes the locks, but a no-start with a security message is a key or immobilizer problem, which owners often misread as a remote failure.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2016 Chevrolet Impala key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Impala in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.