2015 Chevrolet Impala Key Replacement

2015 Impala key specs

The 2014-2020 Impala came two ways. Cars with a key slot use an HU100 flip key with a Philips 46 extended transponder and four or five buttons. Cars with keyless access and push-button start use a proximity fob that looks similar but is a different part, listed under FCC ID OHT05918179. Check the dash before ordering. A 2014-2016 Impala Limited is the previous body and takes the ninth-generation B111 Circle Plus key instead.

What's specific to the 2015 Impala

The 2015 Chevrolet Impala is the second of 7 model years in the Impala Tenth generation (Epsilon II) (2014–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 11 years old, a 2015 Chevrolet Impala has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2015 Impala can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2015 Chevrolet Impala

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Chevrolet Impala, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2015 Impala and which we don't.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2015 Chevrolet Impala open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Chevrolet immobilizer works on the Impala

• The turn-key flip remote, FCC ID OHT01060512, is shared with the 2010-2015 Camaro, 2011-2015 Cruze and 2013-2016 Malibu.
• Keyless-access Impalas use a proximity fob listed under OHT05918179, which will not work in a key-slot car.
• If your registration reads Impala Limited, the car is the older 2006-2013 design and uses that generation's key.

Programming a 2015 Impala key

Flip keys are cut on a laser machine and programmed over OBD-II, and GM's on-board add works when you already have two recognized keys. Proximity fobs are registered with a programmer and have no on-board option. For all-keys-lost, the programmer registers new keys on either version, and some flip-key cars also accept GM's 30-minute relearn. The emergency blade in a proximity fob is cut to the door lock.

Lost every key to your Impala?

When every key is gone, the route depends on the system. On Passlock and PASS-Key II vehicles we cut a new key from the code or by decoding a lock, add the right resistor pellet where needed, and the vehicle starts with no programming. Circle Plus and HU100 transponder vehicles get a freshly cut key programmed over OBD-II, and GM's own 30-minute relearn also works on many of them, erasing the lost keys in the process. Proximity-fob models need a new fob, an emergency blade cut to the locks and a programmer, often with a long security wait. Global B models and the electric Blazer EV and Equinox EV may need online authorization or the dealer, and we tell you which before starting. Expect to show ID and proof of ownership first.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Chevrolet Impala can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Impala and your schedule.

Impala key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Impala uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chevrolet Impala keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Chevrolet system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Impala key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Impala came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chevrolet key problems

• Flip keys on the Camaro, Cruze, Equinox and Impala tend to break at the hinge, leaving the blade floppy or unable to lock open. The transponder and circuit board usually survive, so a new shell often avoids programming a whole new key.
• Inland Empire heat is hard on fob batteries and on the plastic heads of older transponder keys. A cracked head can let the chip shift or fall out, which typically leaves you with a key that turns the ignition but will not start the engine.
• Global B models such as the 2023 and newer Colorado, the 2025 and newer Equinox and the C8 Corvette use a CR2450 fob battery rather than the CR2032 found in earlier Chevy fobs. The two cells are not interchangeable, so check before buying.
• A flashing security light with a crank-no-start, or an engine that dies after a few seconds, is the classic Passlock fault on 2000-2005 Impalas, Cavaliers, S-10 Blazers and first-generation Avalanches. The cylinder sensor or its wiring is usually to blame, not the key.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2015 Chevrolet Impala key?

Don't wait until the last key disappears. If your Chevrolet Impala is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.