2014 Chevrolet Impala Key Replacement

2014 Impala key specs

The 2014-2020 Impala came two ways. Cars with a key slot use an HU100 flip key with a Philips 46 extended transponder and four or five buttons. Cars with keyless access and push-button start use a proximity fob that looks similar but is a different part, listed under FCC ID OHT05918179. Check the dash before ordering. A 2014-2016 Impala Limited is the previous body and takes the ninth-generation B111 Circle Plus key instead.

What's specific to the 2014 Impala

2014 was the first model year of the Impala Tenth generation (Epsilon II). Early-production cars sometimes use different part numbers than later ones, so for a 2014 Chevrolet Impala we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2013 Impala used a transponder (chip) key and a key with a separate remote fob, while the 2014 uses a flip key and a smart proximity key with push-button start. Keys from the older car will not work in this one.

At roughly 12 years old, a 2014 Chevrolet Impala has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit. Smart-key cars like the 2014 Impala can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2014 Chevrolet Impala

• Flip (switchblade) key. A flip key folds its blade into the fob on a spring-loaded hinge and swings it out with the press of a button. Inside the body sit the transponder chip and the remote circuit board, which means the metal blade itself carries no electronics. That's good news when the blade snaps. On many flip keys for a Chevrolet Impala, we can cut a new blade to your key code and fit it into your existing fob, with no reprogramming required, because the chip and remote never left the housing. Many flip-key blades are laser-cut, with a groove milled along the side rather than notches on the edge, so they need a code machine built for that profile.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2014 Chevrolet Impala open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Chevrolet immobilizer works on the Impala

• The turn-key flip remote, FCC ID OHT01060512, is shared with the 2010-2015 Camaro, 2011-2015 Cruze and 2013-2016 Malibu.
• Keyless-access Impalas use a proximity fob listed under OHT05918179, which will not work in a key-slot car.
• If your registration reads Impala Limited, the car is the older 2006-2013 design and uses that generation's key.

Programming a 2014 Impala key

Flip keys are cut on a laser machine and programmed over OBD-II, and GM's on-board add works when you already have two recognized keys. Proximity fobs are registered with a programmer and have no on-board option. For all-keys-lost, the programmer registers new keys on either version, and some flip-key cars also accept GM's 30-minute relearn. The emergency blade in a proximity fob is cut to the door lock.

Programming a Chevrolet key starts with identifying the system. PASS-Key II keys are never programmed; we measure the resistor value and cut a blank with the matching pellet. Passlock keys only need cutting, though the theft module may need GM's timed relearn after cylinder work. Circle Plus and HU100 transponder keys are added through the OBD-II port with a key programmer, and GM's owner's manuals also describe an on-board add when you already hold recognized keys. Separate keyless-entry remotes are learned as their own step. Proximity fobs on Global A models, such as the 2016-2024 Camaro and the 2018-2024 Equinox, are registered over OBD-II with no on-board shortcut. Global B vehicles need a tool with a live online connection, and some jobs still require dealer software. Before any of it, we check your ID and registration so we know the vehicle is yours.

Lost every key to your Impala?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Chevrolet Impala can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2014 Chevrolet Impala we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Impala key battery

Most fobs for a 2014 Chevrolet Impala open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Impala uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chevrolet Impala keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chevrolet keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Chevrolet system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Impala key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Chevrolet system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2014 Chevrolet Impala key?

Need a key for your 2014 Chevrolet Impala? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.