Magnetic Lock Installation in San Bernardino

How this works in San Bernardino

A magnetic lock draws power the whole time the door is locked, usually from a 12 or 24 volt DC supply, and that supply becomes the heart of the system. A good install has a regulated, fused supply, suppression on the lock circuit so reader electronics don't pick up noise, and a relay arrangement that lets the fire alarm cut power. Battery backup keeps doors locked through short outages, but batteries age and need replacing every few years. A door-position sensor and a bond sensor, which confirms the magnet is actually seated, tell the system when a door is truly secure. In a sound design the reader or keypad tells the controller to release the lock, but the controller does not hold the only path to the exit. The sensor, the button and the fire alarm each have their own independent route, and that separation keeps the door safe when something fails.

What we can do on-site

• Header-mounted maglocks on outswing doors. On an outswing door with a sound header, the magnet mounts on the frame above the door and the armature plate mounts on the door face directly beneath. This is the cleanest magnetic lock installation: a straight bolt-up, short wiring and good alignment. We check the header for strength and anchor into solid material, not drywall.
• Inswing doors, brackets and offset mounts. Not every door suits a maglock, and inswing doors are where we are most careful. Sometimes a bracket solves it neatly. Sometimes the geometry points toward an electric strike or other electrified hardware instead. We tell you which before anything is drilled.
• Double doors and paired magnets. On a double door, one weak side defeats the whole opening. We match the holding force to the heavier leaf, mount each plate where the door is stiff, and test by pulling at the weakest point. Wiring both locks on a single release makes them behave as one door.
• Exit sensors and push buttons. Sensors can be fooled by drafts, signs and sunlight, and buttons can be placed where nobody notices them. We review the door's surroundings, aim and set the sensor, mount the button at a reachable height with a visible label, and test both from the exit side, where it matters.
• Power supplies, battery backup and surge protection. Battery backup keeps a maglock holding through short outages and brownouts, though the batteries wear out and the door will release once they are exhausted. We size the battery to your preferences, explain the limits, and put a replacement date on the enclosure so the backup is not forgotten.

What's different about San Bernardino

Inland heat stresses power supplies, batteries and plastic parts. A supply in an unvented ceiling can run hot and fail, and backup batteries age faster. Glass and aluminum doors expand in afternoon sun, which can shift plate alignment slightly through the day. We mount supplies where air moves, check alignment hot as well as cool, and put a battery replacement date on the label.

Wind, brushfire and planned power shutoffs are part of life in foothill communities. A maglock releases when power fails, so a long outage can leave a door unlocked unless you plan for it. We add battery backup sized for realistic outages, suggest a mechanical key lock for off-hours security where the rules permit, and explain what the door will do at each stage so you are never surprised.

Warehouse and industrial doors are heavy, often outswing steel on thin frames, and exposed to forklifts, dust and temperature swings. A maglock needs solid anchoring and a plate that stays aligned despite vibration. Many pedestrian doors on industrial sites in San Bernardino County fall under stricter life-safety rules because workers need dependable exits, so we check that early and may recommend a different lock.

Common situations

• A typical call: a small company keeps its network equipment in a closet with a hollow-metal door and a keyed knob that everyone has copied. The manager wants a keypad. We'd mount an inswing bracket kit, run cable above the ceiling, set a short release time, and discuss whether a strike on the existing latch might be a better fit.
• In a two-story office building, a corridor door leads to a stair enclosure, and someone wants card access on it. Stair doors have specific rules because people must be able to leave the stair in an emergency. We'd talk with the property manager and the fire marshal before touching the door, since the right answer may be a different lock or no change at all.
• For example, a fitness studio has double glass doors off a shared hallway near San Bernardino Valley College. Members badge in, and the owner wants evening entry without handing out keys. We'd fit a magnet on each leaf, wire both to a card reader and controller, add sensors and a push button inside, and connect a fire alarm relay with the landlord's alarm contractor.
• Imagine an aluminum storefront in a strip center with a header only a few inches deep. The tenant likes the look of a concealed lock. We'd compare a surface magnet with a backing plate against a shear lock, explain the cost difference and the header depth required, and get the landlord's approval before drilling a frame they own.

How the visit works

1. Survey the door, header and exit path. Before choosing a magnet, we check what you're attaching it to. A header that flexes, a door that sags or a closer that slams will undermine any lock. We note the problems and, if necessary, fix them before the lock goes in.
2. Design the release path and quote. We decide which magnet or magnets, which brackets and which release devices the door needs: sensor, button, fire alarm relay and credentials. The written quote shows each piece and flags anything that needs an electrician, fire alarm contractor or building official before work begins.
3. Mount the magnet and armature plate. We mark the layout, drill and anchor the bracket or backing plate into solid material, and mount the magnet square to the door. The plate goes on the door with through-bolts and a flexible bushing so it can seat flat against the magnet face, and we tighten everything to specification.
4. Run the power, sensors and fire alarm release. Wiring decides reliability. We use wire of the right gauge for the distance, land connections on terminals instead of twisting wires together, and fuse the supply. Exit devices get their own path, so one failed component can't trap anyone.
5. Program credentials and set the timers. We enter cards, fobs or codes, set the release time and schedules, and decide what happens if someone holds the door open. A short release time discourages tailgating; a longer one helps people carrying loads. We choose a sensible compromise for your door and write it down.
6. Test every release and hand over. Testing covers power on, power off, credential, push button, motion sensor and fire alarm release, with the door pulled hard against the magnet. We also test the batteries, if installed, and show you how to check the system monthly.

What affects the cost

• Door type and mounting hardware. A steel outswing door with a solid header is the simplest mounting. Glass doors need clamp brackets, inswing doors need offset kits, and aluminum storefronts may need backing plates or a concealed shear lock. Mounting hardware is often the biggest single part of the price, so we choose it first.
• Cable route and header access. Where power comes from affects cost as much as hardware. A supply close to the door is cheap; one across the building means heavier wire and more labor. Sometimes moving the supply saves more than any other decision. We look for the nearest ceiling space or closet during the survey.
• Permits, inspections and timing. Life-safety changes may require a permit, plan review or inspection by the fire marshal or building department. Those steps add time and sometimes fees that we do not control. We tell you what we expect and work to the schedule your reviewer sets.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in San Bernardino.

Common errors that cost time and money

• Wiring the exit button through the controller only. If the controller hangs or loses power to its logic, the button does nothing. The push button should interrupt lock power directly, so the door opens even if the access system is dead.
• Powering the lock from a cheap plug-in adapter. Adapters sag, overheat and fail, and when they do the door opens or the lock buzzes. Use a fused, regulated supply with suppression, in a ventilated spot, with labeled wiring. Voltage that sags under load also weakens the magnet, long before the supply fails outright.
• Using a maglock where the door must stay latched. Fire-rated doors, some stairwells and other openings need hardware that latches positively, which a maglock does not do. Ask your building department before you specify one. If you are not sure how your door is classified, look for a label on the edge of the door or frame.

Advice before you book

• Take photos of the top of the door, the header above it and the edge of the door. Include any glass stops, closers or conduit in view. With those we can often pick the bracket kit and the mounting approach before we arrive.
• Aim the exit sensor with care. It should see people approaching from inside, not passers-by outside or sunlight on a glass door. Seal gaps at the bottom of the door and keep paper, signs and decorations out of its view.
• Keep banners, window film and signs off the header and away from the lock. Heat and adhesive can affect the magnet face and the sensor, and a sign can hide the release button. A tidy, visible door is a safer door.
• Think about off-hours security. A maglock lets go when power fails, so a blackout can leave a door unlocked. If that matters overnight, consider battery backup, a separate keyed lock where exit rules allow it, or an electric strike. Each has tradeoffs, and we will walk through them.

Service in San Bernardino

San Bernardino is our home base, so most addresses in town are a short drive. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

We plan the drive the way a delivery route gets planned: freeway first, Tippecanoe Avenue where it makes sense, then the side streets you describe. A landmark or the color of your building helps the technician spot you.

About San Bernardino: Cal State San Bernardino opened in 1965 and anchors the University District in the northwest part of the city, below the mountains.

Business lock or door work in San Bernardino?

Call (951) 903-3193 with the address, the doors or hardware involved and when the site is open. We'll quote the job before any work starts and book a time within our hours that suits your schedule.