San Bernardino Lock Installation for Homes, Rentals and Businesses

Lock Installation in San Bernardino: what to expect

Every lock installation follows the same geometry, whether the hardware is basic or premium. On the face of the door, a 2-1/8 inch cross bore holds the lock chassis. From the edge, a 1 inch bore meets it at the backset, the distance from the door edge to the center of the cross bore, which is almost always 2-3/8 or 2-3/4 inches. The latch or bolt faceplate sits in a shallow mortise so it lies flush with the edge. On the jamb, the strike gets its own mortise plus a deeper pocket for the bolt to travel into. When any of these measurements drift by even a sixteenth of an inch, you feel it: a latch that drags, a deadbolt that needs the door pushed, a knob that sags. We use boring jigs and faceplate templates so holes come out square and centered, then check the reveal between door and frame before setting the strike. In San Bernardino, where summer heat and winter rain make wood doors move through the year, we also position the strike so the latch still catches when the door swells a little.

What we can do on-site

• Fresh boring on new and blank doors. Remodels, ADUs and replacement doors often stall because the new slab is blank. We bring hole saws, auger bits and templates to prep it on-site in San Bernardino, including a deadbolt bore spaced correctly above the knob or handleset. Fiberglass and steel get slower, cleaner cuts that protect the skin from chipping.
• Entry locksets, handlesets and deadbolt pairs. Front doors get the hardware people touch most. We install knob-and-deadbolt pairs, lever sets and full handlesets with a thumb-press grip, then adjust the deadbolt so it throws with a fingertip rather than a shoulder. Every cylinder on the door is keyed to one key before we call it finished.
• Grade 1 commercial cylindrical levers. Offices and shops need levers that survive constant daily use. We install heavy-duty cylindrical locks such as the Schlage ND, Sargent 10 Line and comparable Corbin Russwin models with through-bolted trim, choosing the right function for each door: office/entry, storeroom, classroom or passage. The correct function prevents lockouts and keeps exits usable.
• Keying new locks alike or to your existing key. Mixing Schlage and Kwikset on one house normally means two keyways and two keys. We plan around that by choosing one brand for every exterior door, or by selecting hardware that accepts the keyway you already use. Settle that before the install and you end up with a single key instead of a crowded ring.
• Strike installation and frame reinforcement. The strike is the half of the lock most people never think about. During installation we cut a full-depth bolt pocket, add a strike box so the bolt lands in a clean metal cup, and drive screws long enough to bite the framing stud behind the jamb rather than just the thin jamb wood.

How San Bernardino shapes the job

Older commercial buildings in downtown San Bernardino often mix original wood doors, decades-old mortise locks and newer storefront glass. Lock installation in those spaces takes judgment: some vintage mortise pockets can accept a modern Grade 1 mortise body, others need a conversion, and upper-floor office doors may be fire-rated. We assess each door separately and preserve the building's character wherever the owner wants it kept.

Older San Bernardino homes often have 1-3/8 inch exterior doors, 2-3/8 inch backsets, and sometimes original mortise pockets or extra holes left by decades of swaps. Lock installation there is part detective work: we find where solid wood remains, choose hardware whose trim covers old scars, and reinforce jambs that have been rescrewed too many times. Thin doors may need a thin-door kit for a modern deadbolt, and original glass knobs can sometimes stay as decorative pieces beside it.

In apartment buildings, lock installation decisions belong to the owner or manager, and California Civil Code 1941.3 requires a working deadbolt on each unit's main swinging entry door. For San Bernardino property managers, we install consistent Grade 2 hardware across units so parts and keys stay interchangeable, key each unit separately, and keep a record of codes. Tenants who want added hardware should get written permission first, and we'll ask to see it before drilling.

Example situations

A family in a Verdemont tract wants to replace the builder-grade knob and deadbolt on their front door with a Grade 1 Schlage handleset after the old one started sticking every summer. We would measure the bore and backset, confirm the door is 1-3/4 inches thick, fit the new handleset and center the strike. Before leaving, we test it with the door shut and hand over the keys.

• A boutique moving into a strip center near California State University inherits an aluminum storefront with a deadlock nobody has keys for and a broken thumbturn. We install a new narrow-stile deadlock, a mortise cylinder outside and a correctly sized thumbturn inside, then align the hookbolt so it fully engages the jamb. The owner walks into opening day holding the only new keys.
• Say an HOA requires matte black exterior hardware and a homeowner's new front door came with a satin nickel lock. We help pick a compliant handleset and deadbolt that fit the existing 2-1/8 inch bores, install the set, and key it to the side and garage doors, so the change satisfies the architectural committee without a single new hole.
• A typical call: someone orders a Grade 1 lever set online, then discovers its latch is fixed at 2-3/4 inches while the door is bored at 2-3/8. Rather than redrilling a good door, we source the manufacturer's matching latch in the shorter backset, swap it in, deepen the faceplate mortise slightly and set the lever handing. The original holes stay, and the lever works smoothly.

Step by step with Julian's Locksmith

1. Measure the door and confirm authorization. Tenants are welcome to book a lock installation, but drilling a door changes the landlord's property, so we ask for the owner's or manager's written OK first. Owners show ID along with a deed, tax bill or utility statement. Then the tape measure comes out.
2. Choose hardware that fits the door and the job. With measurements in hand, we go over function, grade, brand, finish and keyway. If you've already bought hardware, we check it against the door. If you haven't, we bring options or order what you choose, explaining what each grade actually adds for the money.
3. Prep the door: bore, edge bore and mortises. Fiberglass and steel get slower speeds and sharp bits, hollow-core doors get checked for their lock block, and older wood doors get inspected for buried nails or old filler. Chips and dust are vacuumed out of the bore so the chassis seats cleanly.
4. Set and reinforce the strike. On hollow-metal frames we use the frame's existing strike cutout or a strike designed for it. On wood jambs in San Bernardino homes, we often add a reinforcement plate where an old strike left the wood chewed up, so the new bolt lands in solid material.
5. Mount, adjust and key the hardware. Lever handing, spring tension, thumbturn orientation and cylinder alignment all get set during mounting. For keyed-alike installs, we test every key in every lock. A lock that only turns with jiggling isn't finished, so we keep adjusting until it turns cleanly.
6. Test with the door closed and hand over. Testing means more than turning a key. We check that the latch catches on a gentle close, the deadbolt slides without drag, the inside lever releases freely for a quick exit and the strike doesn't rattle. Then you get your keys and any leftover parts.

How we quote the job

• Hardware grade and who supplies it. Supplying your own lock is fine, and we'll install it. We'll also point out if it's missing parts, has the wrong backset or the wrong function before we start, because those surprises are much cheaper to catch in the driveway than halfway through cutting a door.
• Door material and condition. Doors in San Bernardino take a beating from heat, sprinklers and seasonal rain. Swollen edges, peeling finish and loose hinges are common on doors facing west or south. Correcting alignment and sealing raw wood after boring adds a little time, but it keeps the new lock working when the weather turns.
• Strike and frame reinforcement. Long strike screws are inexpensive; rebuilding a split jamb is more involved. On French doors, the flush bolts and their head and sill receivers add parts, and sliding doors may need auxiliary locks. We itemize each piece so you can decide what to do now and what can wait.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in San Bernardino.

Mistakes to avoid

• Boring a door freehand with a hole saw and a steady hand. Without a jig, the cross bore drifts off square, the edge bore misses center, and the latch drags against the chassis forever after. A few minutes clamping a jig saves a door from permanent sloppy prep.
• Mounting new hardware on a sagging door and enlarging the strike opening until the bolt fits. The door locks, but the bolt sits loose in a gaping hole and the latch rattles. Tightening the hinges with longer screws or a shim first fixes the cause instead of hiding it.
• Putting the cheapest Grade 3 lock on the back or side door because nobody sees it. Doors out of view from the street are exactly where a forced entry happens with less chance of being noticed. Those doors deserve the same grade and strike reinforcement as the front.

Advice before you book

• Keep the paperwork that comes with a new lock: the instruction sheet, the key code card if there is one, and any spare parts like an alternate latch or strike. They make future rekeys, repairs and matching purchases much easier, so tape them inside a cabinet door near the entry.
• Before ordering hardware for a commercial door near San Bernardino International Airport or anywhere else, look at the hinge edge or the frame for a fire label. A labeled door limits what can be drilled and which hardware is allowed, and finding that out after the order arrives costs time.
• Buy the same brand for every exterior door if you want one key. Kwikset and Schlage use different keyways, and a key cut for one physically won't enter the other. Choosing one brand up front avoids carrying two keys or paying to swap hardware later.
• Measure your backset before buying anything: it's the distance from the door edge to the center of the round hole, and it's almost always 2-3/8 or 2-3/4 inches. Check door thickness too. Most residential locks fit 1-3/8 to 1-3/4 inch doors, and anything thicker needs a special kit.

Reaching San Bernardino

San Bernardino is our home base, so most addresses in town are a short drive. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Rush hour on Kendall Drive can stretch a drive considerably. We'd rather give you a realistic arrival window than an optimistic one, and we'll call you if a closure or a crash changes the plan.

About San Bernardino: Brothers Richard and Maurice McDonald opened their original restaurant on E Street in 1940, the beginning of what became the McDonald's chain.

New or replacement locks in San Bernardino?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.