Exit Device Installation in San Bernardino: From Hardware Schedule to Inspection

What to know first in San Bernardino

A good exit device installation begins with measurements most people never think to take. We note which way the door swings and which side the hinges are on, then measure thickness (commercial doors are usually 1-3/4 inches), leaf width and height, and the width of the stile on glass doors. We identify the frame, whether hollow metal, wood or aluminum, and look at what's already cut into the door: old lock bores, hinge gaps, closer holes. We look for a fire label on the hinge edge, check the head of the frame for rod and closer clearance and check the floor where a rod device would catch. For pairs, we measure the gap between the leaves. Photographs go in your job file. The result is a short list of what the opening can accept and what it needs first, so the quote you receive reflects the real door in San Bernardino instead of the one on the drawing.

Work included on a typical visit

• Function and trim selection. We help you decide who needs to come in from outside and how: exit-only with no handle, a fixed pull, a key-operated lever or a thumbpiece with a cylinder. Each choice changes the parts on the outside face of the door, and trim is the item most often chosen wrongly on a rushed order.
• Door preparation for steel, wood and aluminum. Old preps are the hidden work in retrofits. A door that held a lever lockset has holes in the wrong places, and one that held another exit device has a different pattern. We use filler plates, cover plates and fresh templates so the finished door looks planned rather than patched.
• Closer, hinge and coordinator checks. Hinges carry the door's weight, and a new device adds several pounds. Sagging hinges let the door drop so the latch misses its strike by a quarter inch. We tighten, shim or replace hinges, set the reveal evenly and confirm the swing clears walls and stops.
• Pairs, astragals and meeting-stile alignment. Many existing pairs have one leaf bolted shut. Whether that is acceptable depends on the egress width the building needs, and your plan checker decides that. Where both leaves must open, we install a device on each and set the closers and coordinator so they latch in order.
• Final adjustment, testing and documentation. We leave you the information that inspectors and maintenance staff ask for later: device brand and series, finish, cylinder type, the fire label if there is one and the installation date. Photos of the finished door help if you ever need to match parts.

How San Bernardino shapes the job

Older multi-story buildings near the center of San Bernardino tend to mix rated stair doors, tall wood doors and aluminum storefront entries, all installed in different decades. A device that suits one will not fit the next, so we survey door by door and match finishes to existing or historic hardware when the owner requires it. We also work with the building engineer so tenants upstairs aren't disturbed by noise, dust or a door left unlatched.

Warehouses and tilt-up industrial buildings in San Bernardino usually have steel man doors beside roll-up docks, with forklifts and pallet jacks passing close to the frame. Those doors take abuse, so we favor Grade 1 devices, heavy-gauge strikes and a closer sized for a door that gets shoved open by a loaded cart. Our survey includes checking the frame for impact damage, because a device screwed into a bent frame never latches cleanly, however good the hardware is.

Inland summers in San Bernardino push door surfaces past what bare hands can touch, and heat warps frames, thins closer fluid and fades finishes. We check closer settings in the afternoon, when doors behave worst, choose finishes that resist fading and suggest early start times. We open at 6:30 a.m. every day, so most installations finish before the worst heat. Shaded interior corridors are easier on hardware than sun-baked exterior doors.

Situations this covers

• An example from a small precision machine shop in San Bernardino: the only rear door is a steel leaf with a surface bolt added after a break-in. The owner wants the crew to leave quickly and a delivery driver to enter with a key. We install an exit device with a key-retractable outside lever, remove the bolt, and rekey the cylinder to the shop's existing keys.
• A warehouse office in San Bernardino gets a new glass-and-aluminum entry door. The tenant's contractor ordered a standard exit device, which is too wide for the narrow stile. We swap in a narrow-stile model, reposition the strike on the aluminum frame and fit a cylinder that matches the building's keys so the property manager's master key still works.
• A restaurant remodel in San Bernardino moves the kitchen's back door six feet over. The new door is a stock hollow metal unit delivered without hardware, and it opens onto a shared corridor. We confirm the door's label allows a listed fire exit device, install it, then reset the closer so the door latches against the pull of the kitchen exhaust fans.
• A children's learning center signs a lease in a San Bernardino strip plaza. The fire marshal wants the front door to open outward with a device that releases under light pressure, and the existing door swings in. Reversing a swing is a door-and-frame job, so we coordinate with the owner's contractor and install the exit device once the new door is hung.

Step by step with Julian's Locksmith

1. Walk the openings. If you can't be there, we start by phone and photos. You tell us how many doors there are, what they're made of and what your plans or inspector say, and we sketch a plan for the visit so nothing about the doors is a surprise when we arrive with tools.
2. Choose the hardware and approve the quote. Fire-rated and electrified doors get an extra check here. We confirm the device's listing fits the door's label, that any required power and wiring exist and who is responsible for each piece, before the quote is final. Surprises on those doors are expensive, so we look for them first.
3. Stage the parts and plan the day. Common devices are often on the van. Special lengths, finishes and electrified models come from suppliers, and we tell you the lead time honestly. Then we schedule the installation around your business hours, deliveries and tenants, so the work doesn't collide with your busiest stretch.
4. Prepare the door and frame. We mark the template, drill and cut the door, install reinforcement or sleeves where the door needs them, and prep the frame for the strike. Cut edges get touched up so bare metal doesn't start rusting, and the template is checked twice before the first hole is drilled.
5. Mount, align and connect. Electrified models get their wiring and switches connected, usually in coordination with your security contractor. We test the mechanical side first, then each electrical function one at a time, so any fault is easy to trace back to one part of the installation.
6. Test, document and hand over. You receive the device information, cylinder details and keys, along with simple upkeep tips such as keeping floor strikes clean and testing the pad monthly. We note anything we noticed on neighboring doors so you can plan ahead for the next budget cycle.

How we quote the job

• Grade and series of the device. Exit devices are built to different duty levels. Grade 1 hardware stands up to heavy daily traffic in schools, retail stores and warehouses, while Grade 2 suits lighter use. The harder a door is used, the more the higher grade tends to pay for itself in fewer repair calls over the life of the building.
• Lead time and special orders. Discontinued or unusual doors can mean hunting for adapter plates or custom parts. We tell you up front when a job needs components we don't carry, so a delayed shipment never surprises you after the door is already open. Sometimes a modest door repair beats chasing a rare part for weeks.
• Schedule, access and site conditions. Tight access, ladders for high doors, an alley with no parking and work scheduled around business hours all affect time on site. Early starts, which we offer from 6:30 a.m. every day, can keep the work ahead of your customers, and evening slots until 11:30 p.m. suit businesses that close at night.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in San Bernardino.

What not to do

• Laying new flooring after the device is set. A thicker floor raises the finished surface, and the door may then drag, a bottom rod may miss its strike or the latch may no longer line up. Finish the floor first, or plan an adjustment visit once the new surface is in.
• Ordering devices from the schedule without field-measuring the doors. Real leaves vary in width, hand and thickness from the drawing, and walls get framed a half inch off. A device ordered from a sheet and shipped to a door that doesn't fit becomes a return, a re-order and a missed inspection date.
• Forcing a new case onto the old prep with washers, shims or oversized screws. A case that doesn't seat flat twists, binds the pad and wears out early. Proper filler plates and a fresh template take a little longer on installation day and last for years longer than a quick workaround.

Advice before you book

• If an architect or hardware consultant prepared a hardware schedule, send us the page for your doors. When what arrived on site differs from the schedule, fixing it before installation day costs far less than discovering the mismatch with the door already cut. We'll compare the two lines before anyone drills.
• Choose the finish with neighboring hardware in mind. A satin chrome device beside oil-rubbed bronze lever handles looks like an afterthought. Sending us a photo of nearby hardware lets us suggest a finish that blends in or deliberately matches your building standard, which helps when a landlord must approve the work.
• Warn your alarm company before we test door contacts or electric hardware. A monitored door that opens during testing can trigger a dispatch. A quick call to put the system on test status avoids false alarms and the fees that sometimes follow them, and it keeps your relationship with the monitoring center friendly.
• Keep the paperwork that ships with the device: template sheets, installation instructions, the strikes and any spare keys. Put them in your building file with our invoice. Years from now, a maintenance person will thank you for knowing exactly which series is on that door and where to find matching parts.

Getting to San Bernardino

San Bernardino is our home base, so most addresses in town are a short drive. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Our path into San Bernardino depends on where the previous job wrapped up. Sometimes that's a straight run via Tippecanoe Avenue; other times it's surface streets the whole way. Either way, you get a heads-up call when the technician is close.

About San Bernardino: Norton Air Force Base operated on the city's east side from 1942 until 1994, and the site is now San Bernardino International Airport and a large logistics district.

Lock or door hardware trouble in San Bernardino?

Call (951) 903-3193 with the address and what the door or lock is doing. We'll quote the repair before any work starts.