One Key for Every Door: Same Key for All House Locks in Redlands

What to know first in Redlands

Every pin tumbler lock in your house has a plug that turns only when the pins inside it line up at the shear line. Each key's cuts lift a stack of key pins and driver pins to exactly that line. To give you the same key for all house locks, a locksmith removes each plug, dumps the old key pins, and loads new ones whose lengths match the cuts on one chosen key. Springs and driver pins usually stay, although we replace tired springs and corroded pins as we go. Five-pin residential cylinders such as Kwikset KW1 and Schlage SC1 take only a few minutes each once the lock is off the door; handlesets, mortise cylinders and smart deadbolts take longer because there's more to disassemble. The new combination comes from a key we cut by code, not from copying one of your old keys, so wear doesn't carry forward. When every cylinder is back on the door, we test each one with every new copy, from outside and inside, with the door open and then closed against the strike. Your previous keys stop working at all of those doors at once.

Work included on a typical visit

• Security screen door deadbolts. Security screen doors in Redlands take a beating from afternoon sun, slamming and dust. Before we rekey the lock to your house key, we check that the bolt throws fully into the frame and that the cylinder isn't packed with grit. A gritty cylinder gets cleaned and treated with a dry lubricant so the new key turns easily.
• Garage entry and side door locks. Garages are often where mismatched keys hide: a knob-only lock on the house-to-garage door, a builder-grade knob on the side door, maybe a padlock on a storage cabinet. We bring the passage doors onto your house key and recommend adding a deadbolt where there's only a knob. The overhead door handle usually stays separate.
• Gates, sheds and padlocks. A side gate, shed or pool equipment enclosure can join the house key if the lock has a rekeyable cylinder. Many keyed gate latches and commercial-grade padlocks do; cheap blister-pack padlocks usually don't. Where a lock can't be re-pinned, we suggest a rekeyable replacement that takes your keyway, if one exists for your brand, and set it up to match.
• Cutting and testing your new keys. Before we leave, every new key opens every door it should, and every old key you hand us fails in every lock. We check both directions. It's the only way to be sure no cylinder got missed, which matters with a one-key plan, because a single unmatched door means carrying a second key again.
• Matching new hardware to your existing key. Once the house runs on one key, a new deadbolt or replacement knob doesn't have to break the system. Buy hardware in the same brand and keyway, or let us supply it, and we key the new cylinder to your existing combination during installation. You won't need a second key, and the pattern stays intact.

What's different about Redlands

Busy households are where one key pays off most. Kids coming home from school, a parent leaving early, a grandparent watching the children after work: nobody wants to explain which key opens the side door. In the family neighborhoods of Redlands, rekeying the front, back and garage entry doors to one key means every family member carries the same key and gets inside on the first try.

Older homes in Redlands often carry decades of hardware layers: an original knob, a deadbolt added later, a mortise lock on the front door, maybe a rim night latch nobody uses anymore. Getting one key for that mix starts with sorting what can be rekeyed, what accepts a standard cylinder and what has to be replaced. Original mortise bodies are often worth keeping, because many accept a modern threaded cylinder in your house keyway.

Foothill homes often have more exterior doors than flatland houses: walkout lower levels, side doors onto decks and gates on steep paths. In wildfire country there's another reason for one key. When an evacuation order comes and you're grabbing what you can, a single key that locks every door is one less thing to sort out on the way down the hill.

Common situations

• Say an older Spanish-style home near San Bernardino County Museum still has its original mortise lock on the front door, plus a newer deadbolt above it. The owner wants both on one key along with the back door. If the mortise body is sound and accepts a standard threaded mortise cylinder, we'd fit one in the house keyway and key it to match the deadbolt and back door.
• For example, a house off Tennessee Street has a steel security screen door whose deadbolt uses a different key from the wood door behind it, so every trip inside takes two keys. After confirming the screen door's cylinder is a standard KW1 type, we'd rekey it and the entry deadbolt to the same new key, then adjust the screen door's strike, which had been catching on every close.
• Picture a grandmother who's started having trouble telling her keys apart, especially at dusk. Her family asks for one key across the house. We'd rekey the front, back and garage doors to match, cut a key with a large rubber head that's easy to grip, and check that each deadbolt turns with light pressure, adjusting a strike that had been forcing her to shove the door.
• A typical call: the front door has a Schlage deadbolt and handleset, the back door a Kwikset knob and deadbolt left from an old repair, and the garage entry a Schlage knob. The owner wants one key. Since three of the five cylinders are already Schlage, we'd rekey those, replace the two Kwikset pieces with Schlage hardware, and set everything to one fresh combination.

From your call to the finished job

1. Send photos and a count of your locks. Tell us what's on the ring now: how many different keys, which doors they open, and whether any lock has no key at all. That last detail matters, since a lock without a working key needs picking or decoding before it can be rekeyed with the others.
2. Gather a working key for each lock. Locks that no one has a key for, like a back door that's always been bolted from inside, aren't a dead end. We can usually open them without damage and rekey them with the rest. Just mention them ahead of time so the schedule allows for the extra work.
3. Verify ownership and confirm the plan. This is the moment to raise anything you're unsure about: whether the gate should be included, how many keys to cut, or whether a tired knob should be replaced. We'd rather settle those questions now than halfway through, and the quote reflects the final list.
4. Pick the new key combination. The new key is cut by code first and becomes the pattern for every cylinder. Starting from a fresh, code-cut key avoids inheriting wear from an old copy, which matters because every lock in the house will be pinned to it.
5. Rekey and reinstall each cylinder. Knobs, levers, deadbolts and handlesets each come apart differently, and smart locks need their interior units removed and reconnected. We work carefully around finishes, keep track of every small part, and lubricate each cylinder lightly before reassembly.
6. Test every door and hand over the keys. With all locks back on, we test each new key in every door from outside, with the door closed so the bolt has to drive into the strike. Your old keys get tried too, and they should fail everywhere. Then you get your copies, and we count them with you.

How we quote the job

• How many cylinders you're matching. Counting locks before you call keeps the quote honest. People often forget the garage side door or a lock on the security screen, then add them during the visit. That's fine, since we'll requote on the spot, but a complete count from the start lets you budget accurately.
• Missing keys and stuck locks. A working key for each lock keeps the job simple. A lock with no key has to be opened first, by picking or decoding, before it can be rekeyed. That's usually still cheaper than replacing it, but it adds labor, so let us know in advance which locks have no key.
• Timing, travel and combined work. Combining jobs on one visit saves a second service call. If you also need a new deadbolt installed, a smart lock set up or a broken knob replaced, mention it when booking. We can key everything to the same new combination during that single trip to Redlands.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Redlands.

Common errors that cost time and money

• Giving copies of the one key to every contractor, cleaner and neighbor who asks. Each copy opens every door you own. Track who has keys, use keypad codes or a separate key for limited access, and collect copies when the work ends.
• Assuming a smart lock removes the need for a matching key. Every keypad with a backup cylinder still has a physical key, and dead batteries are a real possibility. If that cylinder isn't keyed to the house, you'll be hunting for a separate key at the worst possible time.
• Spraying oil into stiff cylinders right before the rekey. Oily residue holds dust and grit, which makes pins sluggish and can hide wear we'd otherwise spot. If a lock is sticking, leave it alone and mention it; we'll clean it properly during the visit.

What to do before we arrive

• Ask for the new key to be cut by code, and keep the invoice that records the keyway. Future copies made from the code will match perfectly, while copies made from worn copies gradually lose accuracy and can leave one door that only opens with a wiggle.
• Bundle the one-key rekey with any other lock work you've been putting off. Replacing a wobbly knob, adding a deadbolt or installing a smart lock during the same visit means everything gets keyed to the new combination at once, instead of paying for a second trip later.
• Check that each deadbolt turns easily with the door closed. If you have to push or pull the door to throw the bolt, the strike is misaligned. Get that fixed during the visit, because a dragging bolt strains the key, and with one key in use everywhere, a bent key affects every door.
• If you rent, get the landlord's written permission before any rekey, and plan to give them a copy of the new key if your lease requires it. Many landlords are happy to approve one-key keying, especially when the tenant covers the cost and the work is done by a licensed locksmith.

Getting to Redlands

Redlands is about 19 miles from our San Bernardino base, roughly 25 minutes in light traffic via Belmont Ave and Palm Ave to I-215 South. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Traffic matters more than mileage. We check conditions on SR-210 and its connecting routes before quoting you a time, and we don't pretend a long drive through heavy congestion is a short one.

About Redlands: Esri, the geographic information systems company Jack Dangermond founded in 1969, is headquartered in Redlands and ranks among the city's largest employers.

Planning a rekey in Redlands?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.