2025 Toyota Mirai Key Replacement

2025 Mirai key specs

The second-generation Mirai uses a four-button smart key with lock, unlock, trunk and panic buttons; catalogs list FCC HYQ14FLA under Toyota parts 8990H-62030 and 8990H-62140, powered by a CR2032. Entry is by touching a door handle, and the car starts with the POWER button whenever the fob is inside the cabin. An emergency blade slides out of the fob for the driver's door. This is a different fob from the first-generation car's, so the two generations can't share keys.

What's specific to the 2025 Mirai

The 2025 Toyota Mirai is the fifth of 6 model years in the Mirai JPD20 (2nd generation) (2021–2026), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At 1 year old, a 2025 Toyota Mirai is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Key options for the 2025 Toyota Mirai

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2025 Toyota Mirai is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Toyota immobilizer works on the Mirai

Toyota phased in transponder immobilizers model by model, so two Toyotas from the same year can need very different keys. Starting with the 1998 model year, the Camry, Avalon, 4Runner, Sienna and Land Cruiser used a fixed-code Texas 4C chip, while US Corollas, the Echo and other economy models kept plain mechanical keys into the mid-2000s. Between 2003 and 2005, depending on the model, the encrypted Texas 4D-67 chip took over. Around 2010 came the 80-bit G chip, and from about 2014 the 128-bit H chip, also called 8A. Many of these later keys carry a stamped D, G or H on the blade. Smart keys spread to US Toyotas with cars like the 2004 Prius, 2005 Avalon and 2007 Camry, moved to 128-bit fobs in the 2010s, and since about 2022 Toyota has used a newer generation: Texas 8A BA-type fobs in models such as the bZ4X and Crown, and NXP Hitag AES, often called 4A, in the Corolla, Corolla Cross and 2025 Camry. Partner-built cars follow their partner's rules, so the 86 and GR86 use Subaru systems and the GR Supra uses BMW's. The letter on your blade, the FCC ID on your fob and your VIN tell us which system we are working with.

• Key suppliers list the HYQ14FLA fob as not reusable, so it should be bought new rather than taken from another car.
• Toyota continued the second-generation Mirai through the 2026 model year, still sold new primarily in California.
• First-generation HYQ14FBA fobs will not work on these cars, even though both generations use a four-button layout.

Programming a 2025 Mirai key

New fobs must be registered with professional equipment; there is no on-board method. On current tools, adding a fob to this generation usually involves online data for Toyota's 128-bit smart system, and some cars need a direct connection at the smart key ECU. All-keys-lost is less widely supported than on high-volume Toyotas, so we confirm by VIN first and will tell you plainly if a Toyota dealer that services fuel-cell vehicles is the better route.

Spare fobs can be added on many cars with current tools. All-keys-lost support is limited on this low-volume car, and some cases need the dealer.

Lost every key to your Mirai?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Toyota Mirai can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Toyota Mirai, ask us directly and you'll get a plain answer.

Mirai key battery

Most fobs for a 2025 Toyota Mirai open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Mirai uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Toyota keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Mirai, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Mirai key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Toyota key problems

• Toyota chip keys are easy to mix up. Many later keys are stamped near the head with D for the 4D-67 chip, G for the 80-bit G chip or H for the 128-bit H chip, and a key ordered by looks alone often won't program.
• Older Toyotas came with black master keys and gray valet keys. The valet key starts the car but can't be used for Toyota's on-board method of adding keys, so a car with only valet keys left needs programming equipment.
• Toyota smart keys look alike across models but carry different FCC IDs and board numbers. Suppliers warn, for example, that a 2007-2010 fob with an E board won't substitute for one with a numbered 0140 board.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2025 Toyota Mirai key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Mirai in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.