2021 Toyota Mirai Key Replacement

2021 Mirai key specs

The second-generation Mirai uses a four-button smart key with lock, unlock, trunk and panic buttons; catalogs list FCC HYQ14FLA under Toyota parts 8990H-62030 and 8990H-62140, powered by a CR2032. Entry is by touching a door handle, and the car starts with the POWER button whenever the fob is inside the cabin. An emergency blade slides out of the fob for the driver's door. This is a different fob from the first-generation car's, so the two generations can't share keys.

What's specific to the 2021 Mirai

2021 was the first model year of the Mirai JPD20 (2nd generation). Early-production cars sometimes use different part numbers than later ones, so for a 2021 Toyota Mirai we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. The key style carried over from the previous generation, but immobilizer data and part numbers can still differ, so a key from a 2020 is not a safe substitute.

A 2021 Toyota Mirai is about 5 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up. Smart-key cars like the 2021 Mirai can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2021 Toyota Mirai

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2021 Toyota Mirai is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Toyota immobilizer works on the Mirai

• Key suppliers list the HYQ14FLA fob as not reusable, so it should be bought new rather than taken from another car.
• Toyota continued the second-generation Mirai through the 2026 model year, still sold new primarily in California.
• First-generation HYQ14FBA fobs will not work on these cars, even though both generations use a four-button layout.

Programming a 2021 Mirai key

New fobs must be registered with professional equipment; there is no on-board method. On current tools, adding a fob to this generation usually involves online data for Toyota's 128-bit smart system, and some cars need a direct connection at the smart key ECU. All-keys-lost is less widely supported than on high-volume Toyotas, so we confirm by VIN first and will tell you plainly if a Toyota dealer that services fuel-cell vehicles is the better route.

Spare fobs can be added on many cars with current tools. All-keys-lost support is limited on this low-volume car, and some cases need the dealer.

Lost every key to your Mirai?

Losing every Toyota key is solvable in most cases, but the method depends on the system. On 4D-67 and G-chip cars, our equipment resets the immobilizer through OBD-II, usually after a built-in security wait, and then registers new keys. H-chip and 8A smart key cars usually need an emulator or a direct connection at the immobilizer or smart key box, which can mean removing a panel under the dash. Older 4C cars and early smart key systems may need the module's memory read on the bench. Toyota's newest BA and Hitag AES systems have aftermarket all-keys-lost coverage on many models but not all, and the BMW-built GR Supra is a dealer job. We confirm your VIN before driving out, verify ID and ownership on site, and program at least two keys.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Toyota Mirai can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Toyota Mirai requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2021 Toyota Mirai we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Mirai key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Mirai uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Toyota keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Toyota system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Mirai key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Toyota key problems

• A used Toyota smart key bought online is already locked to its first car. Many 2004-2020 fobs can be professionally reset for reuse, but fobs from the newest systems may not be resettable, so buying used can waste money.
• Toyota chip keys are easy to mix up. Many later keys are stamped near the head with D for the 4D-67 chip, G for the 80-bit G chip or H for the 128-bit H chip, and a key ordered by looks alone often won't program.
• Toyota fob batteries vary by family. The 2009-2012 Camry-style smart key takes a CR1632, many 2016-2022 fobs take a CR2032, and larger 2022-and-later fobs take a CR2450. Most remote-head keys use a CR2016, while older separate remotes use a CR2032.
• Many newer Toyota fobs have a battery-saving mode, switched on by holding lock and pressing unlock twice. Afterward the car ignores the fob in your pocket until a button is pressed, which owners often mistake for a dead key.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2021 Toyota Mirai key?

Don't wait until the last key disappears. If your Toyota Mirai is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.