2024 Toyota Mirai Key Replacement

2024 Mirai key specs

The second-generation Mirai uses a four-button smart key with lock, unlock, trunk and panic buttons; catalogs list FCC HYQ14FLA under Toyota parts 8990H-62030 and 8990H-62140, powered by a CR2032. Entry is by touching a door handle, and the car starts with the POWER button whenever the fob is inside the cabin. An emergency blade slides out of the fob for the driver's door. This is a different fob from the first-generation car's, so the two generations can't share keys.

What's specific to the 2024 Mirai

The 2024 Toyota Mirai is the fourth of 6 model years in the Mirai JPD20 (2nd generation) (2021–2026), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At 2 years old, a 2024 Toyota Mirai is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Smart-key cars like the 2024 Mirai can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2024 Toyota Mirai

• Smart proximity key (push-to-start). A smart or proximity key lets a 2024 Toyota Mirai open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Toyota immobilizer works on the Mirai

• Key suppliers list the HYQ14FLA fob as not reusable, so it should be bought new rather than taken from another car.
• Toyota continued the second-generation Mirai through the 2026 model year, still sold new primarily in California.
• First-generation HYQ14FBA fobs will not work on these cars, even though both generations use a four-button layout.

Programming a 2024 Mirai key

New fobs must be registered with professional equipment; there is no on-board method. On current tools, adding a fob to this generation usually involves online data for Toyota's 128-bit smart system, and some cars need a direct connection at the smart key ECU. All-keys-lost is less widely supported than on high-volume Toyotas, so we confirm by VIN first and will tell you plainly if a Toyota dealer that services fuel-cell vehicles is the better route.

Spare fobs can be added on many cars with current tools. All-keys-lost support is limited on this low-volume car, and some cases need the dealer.

Lost every key to your Mirai?

Losing every Toyota key is solvable in most cases, but the method depends on the system. On 4D-67 and G-chip cars, our equipment resets the immobilizer through OBD-II, usually after a built-in security wait, and then registers new keys. H-chip and 8A smart key cars usually need an emulator or a direct connection at the immobilizer or smart key box, which can mean removing a panel under the dash. Older 4C cars and early smart key systems may need the module's memory read on the bench. Toyota's newest BA and Hitag AES systems have aftermarket all-keys-lost coverage on many models but not all, and the BMW-built GR Supra is a dealer job. We confirm your VIN before driving out, verify ID and ownership on site, and program at least two keys.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Toyota Mirai can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2024 Toyota Mirai we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Mirai key battery

Most fobs for a 2024 Toyota Mirai open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Mirai uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Toyota keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Toyota system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a Mirai key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Toyota Mirai is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Toyota key problems

• Toyota chip keys are easy to mix up. Many later keys are stamped near the head with D for the 4D-67 chip, G for the 80-bit G chip or H for the 128-bit H chip, and a key ordered by looks alone often won't program.
• Older Toyotas came with black master keys and gray valet keys. The valet key starts the car but can't be used for Toyota's on-board method of adding keys, so a car with only valet keys left needs programming equipment.
• Toyota smart keys look alike across models but carry different FCC IDs and board numbers. Suppliers warn, for example, that a 2007-2010 fob with an E board won't substitute for one with a numbered 0140 board.
• Many newer Toyota fobs have a battery-saving mode, switched on by holding lock and pressing unlock twice. Afterward the car ignores the fob in your pocket until a button is pressed, which owners often mistake for a dead key.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2024 Toyota Mirai key?

Need a key for your 2024 Toyota Mirai? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.