2018 Subaru Impreza Key Replacement

2018 Impreza key specs

The fifth-generation Impreza was the first Subaru with the 128-bit H chip. Lower trims typically have a four-button remote-head key with a side-cut blade, while upper trims, including the Limited, start with a button and use a Keyless Access smart fob. The remote-head key changed internally during the run: 2017-2018 keys use a black button pod and later keys a gray one, even under the same FCC ID. Smart fobs hide an emergency blade for the driver's door.

What's specific to the 2018 Impreza

The 2018 Subaru Impreza is the second of 7 model years in the Impreza GK/GT (fifth generation) (2017–2023), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 8 years old, a 2018 Subaru Impreza has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2018 Subaru Impreza

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Subaru Impreza means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Subaru Impreza GK/GT (fifth generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Subaru immobilizer works on the Impreza

• Supplier listings tie the black-pod CWTB1G077 remote-head key, part 57497-FL00A, to 2017-2018 Imprezas and a gray-pod version to 2019 and later.
• The smart fob for this generation, FCC ID HYQ14AHK, operates at about 434 MHz and takes a CR2032 battery.
• Subaru's bulletin lists a thin 4+4 laser-cut emergency key for the smart-key Imprezas of this generation.

Programming a 2018 Impreza key

With at least one working key, adding a remote-head key or smart fob over OBD-II is routine; the remote is registered at the same time. All-keys-lost on H-chip cars is harder. Some programmers still can't do it on bladed keys, so we use dedicated Subaru software or an emulator, and on a few cars the job means reading a module on the bench. We confirm the method from your VIN before quoting.

Spare keys are routine. All-keys-lost needs specialized Subaru software or an emulator, and a few cars may need dealer help.

Lost every key to your Impreza?

With every key gone, the model year decides the job. A 2000-2004 Subaru, a Baja, or a base model built before its line got an immobilizer just needs a key cut by code or by decoding the door lock. On 4D62 cars from 2005 through 2011 and on remote-head cars of the G-chip years, we cut the blade, erase the missing keys and program new ones in one visit. Keyless Access cars of the G-chip years and every H-chip car are harder: some tools need a working key, so we use dedicated Subaru software or an emulator, and a few cars have to go to the dealer. Brand-new platforms, including the 2026 Outback and Subaru's electric models, are usually dealer jobs for now. We tell you plainly which route your car needs and check ID and proof of ownership before any work.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Impreza can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Subaru Impreza requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2018 Subaru Impreza we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Impreza key battery

Battery details for the 2018 Impreza: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Impreza uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Subaru keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Impreza key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Subaru Impreza is the most involved of all, both in the part itself and in the programming.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Subaru system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Remote-head key shells tend to crack at the blade root after years on a heavy keyring. The remote board and transponder can usually be moved into a new shell with a freshly cut blade, which often costs less than a complete new key.
• Used Subaru fobs sold online can arrive already programmed to another car. Ask whether a fob is new or reset to a blank state before you buy, and bring the part number and FCC ID from your old key so we can confirm the fit before programming.
• Subaru smart keys use different emergency blades. Subaru's bulletin lists a 5+4 laser-cut emergency key for the 2014-2015 Forester, the 2014 Crosstrek Hybrid and the 2015 WRX, and a thinner 4+4 key on later cars. Cut the blade to match your fob, not just the model name.
• Remote-head keys sold under FCC ID CWTB1G077 look alike but differ inside. The 2018-2019 Legacy and Outback versions carry the older G chip, while the 2017-2020 Impreza, Crosstrek, Forester and Ascent versions carry the H chip. Match the part number and pod color, not just the FCC ID.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2018 Subaru Impreza key?

Need a key for your 2018 Subaru Impreza? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.