2017 Subaru Impreza Key Replacement

2017 Impreza key specs

The fifth-generation Impreza was the first Subaru with the 128-bit H chip. Lower trims typically have a four-button remote-head key with a side-cut blade, while upper trims, including the Limited, start with a button and use a Keyless Access smart fob. The remote-head key changed internally during the run: 2017-2018 keys use a black button pod and later keys a gray one, even under the same FCC ID. Smart fobs hide an emergency blade for the driver's door.

What's specific to the 2017 Impreza

2017 was the first model year of the Impreza GK/GT (fifth generation). Early-production cars sometimes use different part numbers than later ones, so for a 2017 Subaru Impreza we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. The key looks similar to the 2016 model's, but the chip moved from Texas 80-bit Subaru G (4D82) to Texas DST-AES 128-bit Subaru H, so an older key is not a substitute.

At roughly 9 years old, a 2017 Subaru Impreza has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit. Smart-key cars like the 2017 Impreza can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2017 Subaru Impreza

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2017 Impreza, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Subaru Impreza GK/GT (fifth generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Subaru immobilizer works on the Impreza

• Supplier listings tie the black-pod CWTB1G077 remote-head key, part 57497-FL00A, to 2017-2018 Imprezas and a gray-pod version to 2019 and later.
• The smart fob for this generation, FCC ID HYQ14AHK, operates at about 434 MHz and takes a CR2032 battery.
• Subaru's bulletin lists a thin 4+4 laser-cut emergency key for the smart-key Imprezas of this generation.

Programming a 2017 Impreza key

With at least one working key, adding a remote-head key or smart fob over OBD-II is routine; the remote is registered at the same time. All-keys-lost on H-chip cars is harder. Some programmers still can't do it on bladed keys, so we use dedicated Subaru software or an emulator, and on a few cars the job means reading a module on the bench. We confirm the method from your VIN before quoting.

A Subaru built before its line got an immobilizer only needs a correctly cut key. We cut from the key code, which Subaru releases by VIN through its lock information service (a paid site for professional locksmiths), or by decoding a lock. Transponder Subarus from 2005 through the G-chip years are programmed through the OBD-II port, and Subaru's own procedure relies on an immobilizer security ID that is released along with the key code. Remote-head keys are normally registered as transmitters in the same session on 2012 and later cars, while the separate fobs of earlier years have their own routines. H-chip cars accept an added key readily when a working key is present, but all-keys-lost needs dedicated Subaru software, an emulator or bench work, and Keyless Access fobs must be new or reset to blank. Bring every key you still have, and expect us to check ID and registration first.

Spare keys are routine. All-keys-lost needs specialized Subaru software or an emulator, and a few cars may need dealer help.

Lost every key to your Impreza?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Subaru Impreza requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2017 Subaru Impreza we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Impreza key battery

Battery details for the 2017 Impreza: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Impreza uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Subaru keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Impreza key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Impreza came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2017 Subaru Impreza key?

The quickest route to a working key for a 2017 Subaru Impreza starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.