2006 Subaru Impreza Key Replacement

2006 Impreza key specs

Most second-generation Imprezas, including the 2.5i, 2.5RS, TS wagon and Outback Sport, use a plain cut key with no chip. Turbocharged models are the exception: the STi got an immobilizer and a 4D62 transponder key starting in 2005, and the WRX followed for 2006 and 2007. A 2002-2005 WRX and the 2004 STi still have plain keys. Keyless entry came as a separate fob in every case, with a two-button design common on 2005-2007 cars, so expect two pieces on your keyring.

What's specific to the 2006 Impreza

The 2006 Subaru Impreza is the fifth of 6 model years in the Impreza GD/GG (second generation) (2002–2007), so it shares its key system with the rest of that run, which makes replacement parts easy to source. A 2006 Subaru Impreza is about 20 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

If a newly cut key turns the 2006 Impreza's ignition but the engine cranks and dies, the transponder isn't recognized yet; that's a programming step, not a cutting problem, and it's handled at the car.

Key options for the 2006 Subaru Impreza

• Basic mechanical key. Before treating a Subaru Impreza key as purely mechanical, we confirm it. Some keys look like plain metal with a rubber or plastic head yet hide a transponder inside, and immobilizers arrived on different trims and model years at different times. If yours truly has no chip, the new key is cut and then tested in the doors, ignition, glove box and trunk where those locks exist. Mechanical blades also show up on newer vehicles as valet keys and as the emergency insert tucked inside a smart fob. Those blades still matter: they're how you get in when a fob battery dies, so they deserve the same careful cutting.
• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2006 Subaru Impreza that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.
• Key with separate remote fob. Pairing a separate remote to a 2006 Subaru Impreza is a different job from programming the ignition key. Some vehicles accept new remotes through an on-board sequence of key turns and button presses; others need a scan tool connected to the OBD-II port. On many of them, entering remote programming mode clears every remote the car already knows, so any remote you want to keep has to be present and re-paired during the same session. Before we start, gather every remote that belongs to the vehicle. Leaving one in a kitchen drawer is a classic way to end up with a remote that quits the day after a new one is added.

How the Subaru immobilizer works on the Impreza

• Subaru's immobilizer chart lists only the STi for 2005 and the WRX and STi for 2006-2007; other Imprezas of these years have none.
• The 2005-2007 two-button remote, FCC ID NHVWB1U711 (part 88036-FE041), is shared with the 2005-2008 Forester.

Programming a 2006 Impreza key

On chipless cars, we cut the key by code or by decoding a lock and you drive away. For a 2005-2007 STi or a 2006-2007 WRX, we cut the blade and then register the transponder through the OBD-II port, using Subaru's immobilizer data for your VIN, so a key can be made from one working key or from none. Separate fobs pair through their own routine or a scan tool. Tell us the trim when you call, because it changes the job.

Lost every key to your Impreza?

With every key gone, the model year decides the job. A 2000-2004 Subaru, a Baja, or a base model built before its line got an immobilizer just needs a key cut by code or by decoding the door lock. On 4D62 cars from 2005 through 2011 and on remote-head cars of the G-chip years, we cut the blade, erase the missing keys and program new ones in one visit. Keyless Access cars of the G-chip years and every H-chip car are harder: some tools need a working key, so we use dedicated Subaru software or an emulator, and a few cars have to go to the dealer. Brand-new platforms, including the 2026 Outback and Subaru's electric models, are usually dealer jobs for now. We tell you plainly which route your car needs and check ID and proof of ownership before any work.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Impreza can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru Impreza, ask us directly and you'll get a plain answer.

Impreza key battery

Most fobs for a 2006 Subaru Impreza open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2025, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Impreza uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru Impreza keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Subaru keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Impreza key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Impreza came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Remote-head keys from 2012 through at least 2022 mostly run on a CR1620 cell, while Keyless Access fobs from 2014 on take a CR2032. The 2024 remote-head key moved to a thicker CR2025. Inland Empire summer heat shortens coin-cell life, and shrinking range is the usual warning.
• Remote-head key shells tend to crack at the blade root after years on a heavy keyring. The remote board and transponder can usually be moved into a new shell with a freshly cut blade, which often costs less than a complete new key.
• Remote-head keys sold under FCC ID CWTB1G077 look alike but differ inside. The 2018-2019 Legacy and Outback versions carry the older G chip, while the 2017-2020 Impreza, Crosstrek, Forester and Ascent versions carry the H chip. Match the part number and pod color, not just the FCC ID.
• If a Keyless Access fob battery dies, the car can usually still be started with the backup method in the owner's manual, which uses the fob and the start button. The emergency blade hidden in the fob opens the driver's door.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2006 Subaru Impreza key?

Don't wait until the last key disappears. If your Subaru Impreza is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.