2012 Subaru Impreza Key Replacement

2012 Impreza key specs

Subaru switched the Impreza to a remote-head key for 2012, and every 2012-2014 car starts with a turn key. Lock, unlock, trunk and panic buttons sit in the head, and the blade is a conventional side-cut instead of the laser-cut key of the previous car. The Crosstrek that arrived for 2013 uses the same key. WRX and STI models of these years kept the older laser key and are covered on their own pages. If a spare you find online has no buttons, it is the wrong generation.

What's specific to the 2012 Impreza

2012 was the first model year of the Impreza GJ/GP (fourth generation). Early-production cars sometimes use different part numbers than later ones, so for a 2012 Subaru Impreza we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2011 Impreza used a transponder (chip) key and a key with a separate remote fob, while the 2012 uses a remote head key. Keys from the older car will not work in this one.

At roughly 14 years old, a 2012 Subaru Impreza has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2012 Subaru Impreza

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2012 Subaru Impreza with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.

How the Subaru immobilizer works on the Impreza

• Supplier listings show two remote-head FCC IDs for this era, CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz, so match the part number on your old key.
• Subaru's key bulletin shows the 2012 and later Impreza remote-head key with a side-cut blade and immobilizer, ending the laser keys of 2008-2011.
• Subaru's bulletin lists the 2012-2014 Impreza master key as part 57497FJ021 and a sub master without remote functions as 57497FJ090.

Programming a 2012 Impreza key

The remote-head key is programmed through the OBD-II port, and the remote buttons are registered in the same session, so there is no separate remote step. The blade is cut on a standard key machine from your key code or by decoding the door lock. Subaru's professional lock-information service supplies the data tied to your VIN, which lets us add a key to your set or replace all of them in one visit. We confirm the FCC ID on your old key before ordering.

Lost every key to your Impreza?

With every key gone, the model year decides the job. A 2000-2004 Subaru, a Baja, or a base model built before its line got an immobilizer just needs a key cut by code or by decoding the door lock. On 4D62 cars from 2005 through 2011 and on remote-head cars of the G-chip years, we cut the blade, erase the missing keys and program new ones in one visit. Keyless Access cars of the G-chip years and every H-chip car are harder: some tools need a working key, so we use dedicated Subaru software or an emulator, and a few cars have to go to the dealer. Brand-new platforms, including the 2026 Outback and Subaru's electric models, are usually dealer jobs for now. We tell you plainly which route your car needs and check ID and proof of ownership before any work.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Impreza can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru Impreza, ask us directly and you'll get a plain answer.

Impreza key battery

If a new CR1620 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Impreza uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru Impreza keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Subaru keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Impreza key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Subaru Impreza is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Subaru smart keys use different emergency blades. Subaru's bulletin lists a 5+4 laser-cut emergency key for the 2014-2015 Forester, the 2014 Crosstrek Hybrid and the 2015 WRX, and a thinner 4+4 key on later cars. Cut the blade to match your fob, not just the model name.
• Used Subaru fobs sold online can arrive already programmed to another car. Ask whether a fob is new or reset to a blank state before you buy, and bring the part number and FCC ID from your old key so we can confirm the fit before programming.
• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• Remote-head key shells tend to crack at the blade root after years on a heavy keyring. The remote board and transponder can usually be moved into a new shell with a freshly cut blade, which often costs less than a complete new key.

Tips from a mobile locksmith

• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2012 Subaru Impreza key?

Need a key for your 2012 Subaru Impreza? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.