2011 Scion xD Key Replacement

2011 xD key specs

The xD came with three-button remote-head keys: lock, unlock and panic in a small head on a TOY43-profile blade, from the same key family as the Yaris and tC. Catalogs list the xD remote both with a 4D-67 chip and in a chipless version marked without anti-theft, and many US-market cars have no immobilizer, so a properly cut plain key can start the engine. A car that does read a transponder, such as a Canadian-market xD, has to have it programmed. Because the blade and electronics share one head, a cracked key usually calls for a new shell rather than a new remote.

What's specific to the 2011 xD

The 2011 Scion xD is the fourth of 7 model years in the xD XP110 (only generation) (2008–2014), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2011 Scion xD is about 15 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2011 Scion xD

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2011 xD, we open the old key and show you what's broken before recommending anything.
• Basic mechanical key. Before treating a Scion xD key as purely mechanical, we confirm it. Some keys look like plain metal with a rubber or plastic head yet hide a transponder inside, and immobilizers arrived on different trims and model years at different times. If yours truly has no chip, the new key is cut and then tested in the doors, ignition, glove box and trunk where those locks exist. Mechanical blades also show up on newer vehicles as valet keys and as the emergency insert tucked inside a smart fob. Those blades still matter: they're how you get in when a fob battery dies, so they deserve the same careful cutting.

How the Scion immobilizer works on the xD

• Replacement remote-head keys for the 2008-2012 xD are sold under FCC ID MOZB41TG and take a CR2016 battery.
• The same remote-head key family is listed for the Yaris and the 2012-2013 iQ, but chip versions differ, so match the stamp on your blade.
• Shells for the 2014 xD list the newer MOZB52TH remote, so check the FCC ID on your key before ordering.
• If your xD has no immobilizer, re-keying the ignition after a key goes missing is the only way to stop that key from starting it.

Programming a 2011 xD key

On a car without an immobilizer, we cut the blade by duplicating, by code, or by decoding the door lock, then pair the remote buttons. Toyota's on-board add routine, a timed series of door, key and lock-button steps, works on many of these cars, and a programmer handles the rest. If your xD reads a chip, the key is registered through OBD-II instead, with an immobilizer reset when no working key is left.

How we make a Scion key depends on which of three groups the car falls into. On the tC, FR-S and iM, the transponder in the key is registered through the OBD-II port with professional equipment, and the buttons on a remote-head or flip key are synced as a separate step. Push-button editions add a smart fob registered the same way. Toyota's 4D-67 and G systems let us add a key from one working key, and the immobilizer can be reset when none are left, though that reset often includes a security wait. On cars without an immobilizer, which covers many xA, xB, xD and iQ models, the job is mostly mechanical: we cut the TOY43-profile blade by code or by decoding a lock, then pair the remote through Toyota's door-and-ignition routine or a programmer, after testing a cut key in case yours reads a chip. The iA follows Mazda smart-key rules, with fobs that must be new or unlocked. First, we check your ID and registration.

Lost every key to your xD?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Scion xD can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Scion xD, ask us directly and you'll get a plain answer.

xD key battery

Battery details for the 2011 xD: CR2016 (remote-head key). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your xD uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Scion xD keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Scion keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Scion system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a xD key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Scion xD is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Scion system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2011 Scion xD key?

Need a key for your 2011 Scion xD? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.