2004 Scion xB Key Replacement

2004 xB key specs

The first-generation xB uses a Toyota-style metal key on the TOY43 profile, with lock, unlock and panic on a separate three-button remote. That remote is the same design Toyota used on several early-2000s models, from the Highlander and RAV4 to the Tacoma and Tundra, so replacements are easy to find. Installer reports say most US xBs of these years have no built-in immobilizer, so a properly cut key normally starts one. We confirm by inspecting your key and testing a cut key on the car before quoting anything beyond cutting and remote pairing.

What's specific to the 2004 xB

2004 was the first model year of the xB XP30 (first generation). Early-production cars sometimes use different part numbers than later ones, so for a 2004 Scion xB we confirm the exact key from the VIN or the old key's FCC ID before cutting anything.

A 2004 Scion xB is about 22 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob.

Key options for the 2004 Scion xB

• Basic mechanical key. A plain mechanical key has no chip and no electronics, just a cut blade that lines up the wafers inside the lock. If your 2004 Scion xB uses one, replacement is mostly a cutting job, but how it's cut matters. Copying a worn key copies its wear, and a duplicate of a duplicate drifts further from spec each time. We prefer to cut by code: we look up or decode the factory bitting, then cut a fresh key to the original depths on a code machine. The result turns smoothly in the doors and ignition instead of needing a jiggle. If the ignition wafers themselves are already worn, we'll point that out too.
• Key with separate remote fob. Pairing a separate remote to a 2004 Scion xB is a different job from programming the ignition key. Some vehicles accept new remotes through an on-board sequence of key turns and button presses; others need a scan tool connected to the OBD-II port. On many of them, entering remote programming mode clears every remote the car already knows, so any remote you want to keep has to be present and re-paired during the same session. Before we start, gather every remote that belongs to the vehicle. Leaving one in a kitchen drawer is a classic way to end up with a remote that quits the day after a new one is added.

How xB keys work on this generation

• Replacement remotes for the 2004-2006 xB are sold under FCC IDs HYQ12BAN and HYQ12BBX and run on a CR2032 cell.
• Because the remote is separate, losing the fob doesn't stop the car from starting, and losing the key doesn't mean buying a new remote.
• There was no 2007 xB, so parts for these cars are listed under 2004-2006 and the next generation starts at 2008.

Cutting a 2004 xB key

Most first-generation xB key jobs are mechanical. We duplicate a working key, cut a new one from the key code, or decode the driver's door lock when nothing is left. The separate remote can usually be paired on board: Toyota's routine uses a timed sequence of door opening and closing, key insertions and lock-button presses to put the system into add mode. If your car turns out to read a transponder, we program the new key through OBD-II instead.

Lost every key to your xB?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2004 Scion xB we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

xB key battery

Battery details for the 2004 xB: CR2032 (separate remote). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
2. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Scion keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
3. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a xB key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Scion key problems

• On a first-generation tC, a spare that was cut but never programmed will turn the ignition and crank the engine, yet the car won't start until the 4D-67 chip is registered. Owners sometimes mistake this for a fuel or starter fault.
• The separate remote on the first-generation xB is a common Toyota design shared with early-2000s Highlander, RAV4 and Tacoma models, so replacements are easy to find and can usually be paired on board without a computer.
• Toyota marks chipped blades with a stamped dot (4D-67), G or H near the head. Replacement remote-head keys for the tC, xB, xD and iQ come in chipped and chipless versions that look alike, so match the stamp and FCC ID before buying one online.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2004 Scion xB key?

The quickest route to a working key for a 2004 Scion xB starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.