2014 Mercedes-Benz CLS Key Replacement

2014 CLS key specs

The C218 kept a fob that plugs into a dash ignition switch, and Keyless-Go cars use a start button in the same slot that pulls out when needed. The CLS550, CLS400 and CLS63 AMG share the layout. Partway through this generation Mercedes switched from FBS3 to FBS4 keys, and since early and late fobs look almost the same, the VIN is what tells us which one your car has. Each fob contains an emergency key.

What's specific to the 2014 CLS

The 2014 Mercedes-Benz CLS is the third of 7 model years in the CLS C218 (2nd generation) (2012–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 12 years old, a 2014 Mercedes-Benz CLS has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2014 CLS can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2014 Mercedes-Benz CLS

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2014 CLS, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Mercedes-Benz CLS C218 (2nd generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Mercedes-Benz immobilizer works on the CLS

• The CLS Shooting Brake wagon of this generation was not sold in the US.
• Early and late fobs look nearly identical, so appearance alone won't tell you which key system a car uses.
• A dealer can block a lost key from starting the car.

Programming a 2014 CLS key

On an FBS3 build, we can usually make a spare by reading the ignition switch and calculating the key password from a working fob, and all-keys-lost may be possible with the switch on the bench. On an FBS4 build, keys are produced by Mercedes-Benz for the VIN and ordered through a dealer, and we don't originate them. We check the VIN before quoting, then handle whichever parts of the job are ours.

How we make a Mercedes key depends on that era. FBS3 cars don't learn keys through a simple OBD-II menu. We read the electronic ignition switch, through the diagnostic port when the car allows it or with the switch removed and on the bench, use data from a working key to calculate the key password, and write a new key into one of the switch's free positions. Once written, a Mercedes key is tied to that car, so a used key from another vehicle generally can't be reused. FBS4 keys, found on most models from about 2015 on, are built by Mercedes-Benz for a single VIN and ordered through a dealer, and we don't make them. Keys for the oldest pre-FBS3 cars usually come the same way. Whatever the year, we check your ID and registration, confirm the system by VIN, and tell you before starting which parts of the job are ours.

FBS3 builds can usually get spare keys from us; FBS4 builds need a dealer-ordered key, confirmed by VIN.

Lost every key to your CLS?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Mercedes-Benz CLS, ask us directly and you'll get a plain answer.

CLS key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare replacement at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your CLS uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Mercedes-Benz system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a CLS key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your CLS came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Mercedes-Benz system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2014 Mercedes-Benz CLS key?

Don't wait until the last key disappears. If your Mercedes-Benz CLS is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.