Electronic Door Lock Installation in San Bernardino

How this works in San Bernardino

The door check takes less time than the install and prevents most callbacks. We start with thickness, because nearly all electronic locks are designed around doors between 1-3/8 and 1-3/4 inches. Then the bores: a 2-1/8 inch hole through the face for the lock body and a 1 inch hole into the edge for the latch. Then backset, the distance from the door's edge to the center of the big hole, usually 2-3/8 or 2-3/4 inches, which most latches adjust to cover. Then material: solid wood, fiberglass skin over foam, steel skin over foam, hollow core or aluminum. Last comes the two-finger test. With the old lock out and the door closed, the bolt should slide into the strike with fingertip pressure. If it needs a shove, the hinges or frame need work before motorized hardware is added. A door that's slightly out of true may have lived with a manual deadbolt for twenty years, but a small motor will complain about it every day.

What we can do on-site

• Hollow-core and interior doors. Hollow doors flex, so latch and strike must line up exactly or the lever feels gritty. We shim and align until the latch glides, add a reinforced strike if the jamb is soft, and set the auto-lock to a sensible delay so nobody gets shut out of their own room.
• Fingerprint and touchscreen locks. Touchscreen locks stay tidy only if the glass does. On busy doors, smudges reveal which digits get pressed, so some models let you press extra digits before or after your code, and others rely on a quick wipe habit. Screens also respond differently to rain and gloves, so we test before we leave.
• Card and fob locks on small-business doors. For a back office or storage room, a standalone card lock can be the right level. Each lock holds its own list, so every door is managed separately. We label each door, record which cards belong where, and leave you a simple sheet. The paperwork matters more than people expect.
• Doors that sag, stick or swell. Motorized bolts are far less forgiving than your hand. A door that sags a quarter inch is fine with a manual deadbolt but can make a motor stall. We tighten hinge screws, swap short ones for 3 inch screws into the framing, and adjust the strike until the bolt travels freely before the lock goes in.
• Aluminum storefront, glass and double doors. Glass doors present the opposite problem: no edge to drill and no mounting surface. Options include a patch-fitting lock, a keyed lock with an electrified strike, or a frame-mounted device. Some of these involve wiring, so a low-voltage contractor may share the job. We'll sort out who does what.

How San Bernardino shapes the job

Older homes in San Bernardino come with doors that have been painted, planed and re-hung many times. Original solid wood slabs are often thicker than 1-3/4 inches, bored for lock sets no longer made, or hung in frames that have shifted. Some carry mortise locks, which need different electronic hardware than a bored door. Near Shandin Hills we measure, check the frame for squareness and repair what is loose before recommending anything. A good old door deserves careful work, not a rushed swap.

Apartment entry doors are often fire-rated slabs hung in metal frames, and management usually controls what goes on them. If you rent in San Bernardino, ask for written approval before buying a lock, and ask how the manager keeps access. We install what is allowed, keep the original hardware so it can be restored at move-out, and verify that you live there before we begin. Never drill a rated door without checking its label first.

Foothill homes face dry heat, Santa Ana winds and dust, all of which punish exterior electronics and door fit. Wind-driven grit gets into keypads and strike pockets, and hillside structures can shift a little over time. Near California State University, we choose weather-sealed hardware, clear dust from the latch bore and recheck the door if it begins to rub after a windy season. Homeowners upgrading to fire-resistant doors should tell us, because rated slabs limit what we can drill.

Common situations

• At a small dental or accounting office near National Orange Show Events Center, the back door staff use all day needs a credential that can be cancelled when someone leaves. We would install a battery card lock on the solid-core door, enroll the cards, and confirm the door still opens freely from inside for exit. Anything the lock cannot do, such as keeping a log of every entry, we would flag.
• Consider French doors between a dining room and a patio. The owner wants a code lock on the active leaf. We would measure the clearance to the glass, check the flush bolts on the inactive leaf, choose a narrow-backplate model, and mount the lock with both doors closed so the bolt meets the strike exactly. The inactive door gets bolted top and bottom before we leave.
• A west-facing door near San Bernardino International Airport takes full afternoon sun, and the keypad lock it replaces faded, glitched and drained its batteries each summer. For this door we would pick a model with a stated operating temperature range, fit the gasket under the exterior plate, and suggest a simple shade fix such as an awning or a tall planter. The hardware matters, and so does where the sun lands.
• A typical call: a family in University District buys a fingerprint deadbolt for a steel front door that has been repainted a few times. The edge bore has dried paint in it and the latch face sits proud of the surface. We would scrape and true the bore, set the faceplate flush, seat the strike deeper in the jamb, and only then mount the lock so the bolt throws smoothly instead of grinding.

How the visit works

1. Describe the door, not just the lock. Photos help a great deal. Have a few on your phone of the door edge, the old lock, the strike and any label on the hinge edge, and we'll talk through what to look for when you call. They let us spot a fire rating, a mortise lock or an oversized bore before we load the van.
2. Measure and test the door on site. If the box and the door disagree, this is where we find out. We compare the lock's template with the actual holes, check which adapters came in the box and confirm the strike will reach solid framing. If anything is incompatible, we explain the options before drilling, and you decide how to proceed.
3. Prepare the door and set the latch and strike. On new or unbored doors we use a jig so the cross bore and edge bore meet cleanly, drilling from both sides to avoid splintering the face. Fiberglass and steel get bits and hole saws suited to the skin. Clean, square bores let a lock sit true and run quietly.
4. Mount the lock and route the cable. The exterior assembly goes on first, with its spindle or tailpiece lined up with the latch. We thread the cable through the door without bending it sharply, because a pinched or kinked cable causes flaky keypads. The interior half mounts over it, and we tighten the screws evenly instead of cranking them.
5. Program credentials and teach the lock the door. We enter each person's credential in front of you and test it from outside. You choose the codes, not us; we only help you avoid weak ones. For a rental or business we label each credential, so removing one later is quick and nobody has to guess which was which.
6. Test the backup and hand it over. Handover includes a short walkthrough and a written note: the lock's model, battery type, where the programming code is stored, and the list of users. Keep the override key somewhere you can reach it, not under a planter. We'll write up a record of the visit if you'd like one for your files.

What affects the cost

• Door material, rating and opening type. Solid wood and steel are straightforward. Fiberglass needs care so it doesn't crack. Hollow-core takes a lock but little reinforcement. Fire-rated doors limit what we may drill, and glass or aluminum storefront doors need purpose-made hardware. The more specialized the opening, the more thought goes into the job, and the quote reflects that.
• Who supplies the lock and how the override is keyed. Some online listings are open-box, refurbished or imported units that lack the right adapters, firmware or even the programming card. We look at what you bought before we quote and tell you if something is missing. A missing part is much easier to solve before we're standing at your door.
• Travel, timing and add-ons. Access can matter as much as distance. A gated community, a locked office suite or a building that requires coordination with management adds steps. Tell us about gate codes, parking and who will be on site to let us in, and we'll plan the visit around it.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in San Bernardino.

Advice before you book

• Exercise the override cylinder. Once a season, turn the key in it and puff a little dry graphite or PTFE lubricant into the keyway. A cylinder that sits unused for years can seize with dust and heat, and you'll discover it on the one day you need it. Never use oil-based sprays in a lock.
• Decide who needs access before the install. List the household, a cleaner, a dog walker, a neighbor, a contractor coming next month. Each gets a separate credential that can be deleted later. Building that list while the lock is half programmed is far harder than planning it ahead.
• Check the gaps around the slab. With the door closed, the reveal should look even on all sides. Tighter at the latch corner means rubbing. Slide a business card around the edge; wherever it pinches, a motorized bolt will struggle. Fixing a rubbing door first often makes the new lock quieter and longer-lived.
• New weatherstripping and door sweeps change how the door meets the strike. A thicker seal pushes the slab away from the frame, and the latch may then fall short. If you're replacing seals near the time of the install, tell us, and we'll set the strike for the finished seal.

What not to do

• Testing with the door open and trusting the result. A bolt can throw perfectly in the air and then miss the strike once the door is shut. Always test with the door closed, latched and the weight of your hand on the handle, and do it several times by hand before any batteries go in.
• Treating a sticking door as a battery problem. Slow motors, half-throws and error beeps get blamed on weak cells, and owners keep swapping batteries. When a bolt drags, look at hinges, strike alignment, paint and seasonal swelling first. Electronics rarely fix a mechanical problem, and fresh cells just drain faster fighting it.
• Buying first and measuring later. A lock that doesn't suit your thickness or backset can't be returned once you've drilled the door. Measure thickness, bore sizes and backset, and photograph the old lock before you order. If you're unsure, call us with the numbers and we'll check them against the model you're considering.

Reaching San Bernardino

San Bernardino is our home base, so most addresses in town are a short drive. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Stuck on the shoulder or in a parking lot along I-215? Get somewhere safe, turn on your hazards, and give us the nearest exit or business so we can find the car without guessing.

About San Bernardino: The National Orange Show began in 1911 to celebrate the region's citrus industry and still lends its name to the events center on E Street.

Smart lock help in San Bernardino?

Call (951) 903-3193 with the lock's brand and model and what it's doing, or what you'd like installed. We'll tell you what can be done on-site and quote it before any work starts.