Door Lock Replacement in Ontario: Start With the Door

How this works in Ontario

Four measurements cover most residential door lock replacement. The cross bore is the large round hole through the face of the door; 2-1/8 inches is the standard, and nearly every current knob, lever and deadbolt is built for it. The edge bore is the smaller hole in the door's edge where the latch slides in, usually 1 inch. The backset is the distance from the door's edge to the center of the big hole, almost always 2-3/8 or 2-3/4 inches, and most new latches adjust between the two. The thickness is typically 1-3/8 inches on interior doors and 1-3/4 inches on exterior ones. Add two details: the latch faceplate, which may be square-cornered or rounded, and the strike on the frame. If everything matches, the job is a straight swap. If the old lock left a bigger hole, an adapter plate or trim ring covers it. If the door was never drilled, we bore it with a hole saw and jig so the cuts are straight and square.

What we can do on-site

• Solid wood and solid-core entry doors. A wood door gives us room to work. If the old lock left chewed edges or a hole that has grown, we can fill and redrill it, or cover it with a wider trim plate. Because wood swells and shrinks with the seasons, we check the latch lines up with the strike in both hot and damp weather.
• Interior passage, privacy and dummy sets. Hollow-core interior doors are light and thin, so they take light latches only. We install passage and privacy hardware with a 2-3/8 or 2-3/4 inch latch to suit the door's backset, and we do not put a deadbolt in a door that cannot support one.
• French and double door hardware. A pair of double entry doors with a loose passive leaf can be pushed open from outside. During door lock replacement we check both leaves, replace tired flush bolts and strikes, and add an astragal or edge guard if the doors meet with a wide gap.
• Aluminum-frame, glass and screen doors. Security screen and storm doors use their own latches and keyed handles, and the originals are often light. We replace worn latch sets and keyed cylinders, add a deadbolt-style option where the frame allows, and key it to the house if you want one key for both doors.
• Pocket, barn and other specialty doors. Odd doors usually come with odd hardware: a thumb latch on a gate-style door, a surface bolt on a closet, a rim lock on an antique. We identify the type, source a matching replacement where one exists and tell you early when a custom part is needed.

Local factors in Ontario

For an apartment in Ontario, door lock replacement depends on who owns the lock. California law requires landlords to provide working deadbolts on main entry doors, so a broken one is often their repair. Some buildings keep every unit on a master key system, which limits what hardware can be fitted. Before we replace anything, we confirm who authorizes the work and whether the new lock must match a building key plan. Patio and interior door locks follow similar rules.

Ontario has plenty of older houses where door lock replacement is not plug-and-play. Original doors may carry mortise locks, skeleton-key escutcheons, glass knobs or bores drilled to sizes no longer standard. Thick old wood often takes modern hardware well once the prep is cleaned up, and we can sometimes keep a period knob while updating the mechanism inside. We check the latch mortise, the bore and the frame before we quote, because old doors like to surprise people.

Heat is hard on door hardware across Ontario. West-facing doors can get hot enough to expand and bind the bolt, plastic parts in cheap locks warp and lubricants dry out. Keypad and smart locks also suffer in extreme temperatures. When we plan a door lock replacement in a hot climate, we choose metal-bodied hardware, check the door for expansion clearance and recommend dry lubricants. If a lock only fails on hot afternoons, the door may need adjusting more than the lock needs replacing.

Common situations

• A 1950s wood door has an old mortise lock, and the only key was lost decades ago. The family wants to keep the look but needs a working lock. We open it, remove the mortise body, check the pocket in the door edge and either rebuild the lock with a new cylinder or convert to a modern bored lock, whichever the door and the owners prefer.
• For example, a homeowner in Ontario Ranch says the back-door deadbolt turns only if she lifts the door by the handle. The wood has swelled a little and the bolt rubs the lower edge of the strike. We reset the strike and ease the mortise, and the original deadbolt works smoothly again. Door lock replacement wasn't needed, so she kept her keys and her budget.
• A keypad lock on a rear door stopped responding after leaking batteries corroded its contacts. The old unit can't be cleaned back to life. We replace it with a new keypad deadbolt that fits the existing holes, set fresh codes, key the backup cylinder to the house key and show the owner where the low-battery warning appears.
• A typical call: a bedroom privacy lock with a push button has jammed with a small child inside. We use the outside release to open the door, then find the latch spring has broken. We replace the set with a privacy lock that has a reliable emergency release, check the strike and confirm the door closes quietly. The child is fine, and the hall now has one matching set.

How the visit works

1. Tell us which door and what it's doing. Describe the symptom in plain words: the key goes in but will not turn, the knob turns without pulling the latch, the door needs a shove to lock. We ask a few questions about the door's age and material, then give you an honest arrival estimate for Ontario and what we expect to carry.
2. Confirm who you are, then look at the door. California's Locksmith Act is administered by the Bureau of Security and Investigative Services, and our license, LCO7891, can be checked at search.dca.ca.gov. We ask for ID and proof of residence or ownership, then look over the door, frame and strike before anything comes off.
3. Read the door and match the hardware. We check the door's material and thickness, measure the cross bore, edge bore and backset, and note the latch faceplate and handing. Those numbers decide whether a new lock drops in or needs an adapter. Then we pick a function and grade that suits the door's job.
4. Agree the quote, then take the old lock off. Once we know what the door needs, we give you a quote covering the lock, any parts and the labor. You decide before we start. When you approve, we remove the old hardware carefully and keep it handy so you can compare parts or take it with you.
5. Fit, align and make it close properly. Exterior doors get extra attention: a reinforced strike, screws that reach the framing and a look at the hinge side. If the door has weatherstripping or a closer, we confirm both still work properly with the new latch in place.
6. Key it, test it and hand it over. If the new lock should match your other locks, we key it to your existing key or rekey a group of doors together. Then we test each key in each lock, so nobody discovers later that the back door key does not work.

Pricing factors

• The door and the lock type. Where the lock sits changes the work too. A thin steel or fiberglass door needs gentler handling than solid wood, and a glass door with a narrow stile takes specialized hardware. We explain how the door itself affects both the parts and the labor.
• Grade, brand and finish. Locks come in grades. Grade 3 suits light residential use, Grade 2 is a solid choice for most front and back doors, and Grade 1 is the heaviest-duty option. Brand and finish move the price too, so we show you the trade-offs between them.
• Repairs the door or frame needs. A lock is only as secure as the wood or metal holding it. Reinforcement plates, longer screws, a new strike or a repaired door edge add to the quote, but they are often what separates a lock that holds from one that loosens within months.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Ontario.

Advice before you book

• Rethink where the spare key lives. If the old spare is under a mat or a fake rock, the new lock hasn't really changed anything. Give a spare to a neighbor or relative, or choose a keypad code you can change, and make sure everyone switches to the new key.
• Measure four things before you shop: the cross bore, the edge bore, the backset and the door thickness. A tape measure is enough. Write the numbers on your phone. Even if you let us do the work, knowing them lets you compare quotes honestly.
• Choose levers over knobs where hands matter. A lever opens with an elbow or a pushed palm, which is easier for children, older relatives and anyone carrying something. They work well on bathroom and bedroom doors. Knobs are still fine on closets and other rarely used doors.
• Remember that wood doors move with the seasons. A lock that binds in humid weeks and runs freely in dry ones is usually reacting to a swollen door. Adjusting the strike or a hinge fixes it more reliably than a new lock, and we are happy to check before you replace anything.

What not to do

• Choosing the style before measuring. A handsome lever set can turn out to need a different bore, thickness or backset than your door has, and learning that with the door half dismantled is a bad moment. Measure the door first, then pick the style, and door lock replacement stays a simple swap.
• Testing the new lock only with the door open. Many bolts bind only when the door is shut, because the bolt meets the strike at a slight angle. Test with the door closed, from both sides, but keep a key in your pocket and a way back inside until you are sure it works every time.
• Replacing a lock that was never the problem. When a door sticks, the bolt misses the strike or the key works only when you lift the handle, the cause is often a sagging hinge, a shifted strike or seasonal swelling. A new lock in the same spot misses the same way.

Getting to Ontario

Ontario is about 25 miles from our San Bernardino base, roughly 33 minutes in light traffic via I-215 North to the I-15 junction at Devore. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Stuck on the shoulder or in a parking lot along Vineyard Avenue? Get somewhere safe, turn on your hazards, and give us the nearest exit or business so we can find the car without guessing.

About Ontario: Toyota Arena opened in late 2008 and hosts the AHL's Ontario Reign, while ONT Field opened in 2026 as home of the Dodgers' Single-A Ontario Tower Buzzers.

New or replacement locks in Ontario?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.