Keyed-Both-Sides Deadbolts in Mentone: Where They Fit and Where They Don't

What to know first in Mentone

A standard single-cylinder deadbolt has a key cylinder outside and a thumbturn inside. A double cylinder replaces the thumbturn with a second key cylinder, keyed alike so one key works both faces. The bolt, housing and strike are the same; the difference is that nobody can open the door from inside without a key. That is the whole point, and also the whole risk. The attack it defends against is specific: a burglar breaks glass in the door, a sidelight or a nearby window, reaches in and turns the thumbturn. If no glass sits within arm's reach of the thumbturn, a double cylinder adds nothing against kicking, prying or drilling, and it adds a lock-in hazard. In Mentone, we start every double cylinder deadbolt installation by measuring where the glass is, what the door is used for, and whether the bolt and strike behind it are strong enough to deserve the upgrade.

What we can do on-site

• Double cylinder deadbolt installation on glass-panel doors. For doors with glass in the panel or beside the lock, we fit a keyed-both-sides deadbolt after checking exits and stile width. The new lock goes into a standard bore where possible, keyed alike on both faces, with a heavy strike behind it. We talk through the key plan before leaving.
• Workshops, detached garages and outbuildings. Detached garages, workshops, pool houses and barns often have glass-panel doors and nobody sleeping inside. A double cylinder deadbolt works well there. We install it on a reinforced strike, key it alike with your other outbuilding locks if you like, and suggest keeping a spare key inside the main house.
• Swapping a double cylinder for a single cylinder. If you inherited a double cylinder deadbolt, lost the key or recognized the exit risk, we can replace it with a single-cylinder deadbolt keyed to your house key. The bores are the same, so it's a quick swap, and we'll point out ways to protect the glass instead.
• Keying, spare keys and the key plan. Because one key does everything, how you store it matters as much as the lock. We suggest a spot near the door but away from the glass, and a spare in a separate place. For households with kids or older relatives, we plan more carefully so nobody has to hunt in an emergency.
• Strike, jamb and frame reinforcement. Glass doors often sit in lighter frames than solid entries. Our installation includes checking frame condition, replacing short strike screws and adding reinforcement where needed. We explain what each addition does and what it costs before we do it, and nothing gets added without your say-so.

Local factors in Mentone

Older homes in Mentone frequently have wood doors with divided glass panes close to the lock, and some already carry a double cylinder from a previous owner. These doors are often the main exit, so we usually recommend a strong single-cylinder deadbolt and laminated glass in the pane nearest the lock. For a rear door that isn't the main route, a double cylinder can make sense. We check stile width before drilling, since old wood can split.

Hillside and foothill homes near Mentone face wildfire evacuation risk and sometimes steep exterior stairs, so a quick exit matters. Smoke and darkness make the seconds a key hunt takes dangerous. A double cylinder on the main exit is a poor trade. We recommend a standard deadbolt on main exits and keep any keyed-both-sides locks for outbuildings that aren't part of an evacuation route.

On larger properties around Mentone, outbuildings such as workshops, equipment sheds and guest cottages often have glass-panel doors far from the house. A double cylinder deadbolt suits those buildings when nobody sleeps inside. We install it on a reinforced frame, key several buildings alike and keep the ring manageable. Long driveways make break-ins easy to miss, so the lock and strike should be heavy.

Example situations

• The owner of a boutique has a glass-panel rear door with a thumbturn within reach of the pane. Employees use that door to leave, and it opens onto an alley. A double cylinder would slow an emergency exit. We install a Grade 1 single-cylinder deadbolt with a heavier strike, keep the thumbturn, and suggest security film on the glass so the front and alley doors keep their exit capacity.
• An owner buys a double cylinder deadbolt online for a 2-1/4-inch solid door, and the key turns but the bolt doesn't move. The tailpiece is too short for the thickness. We switch to a thick-door kit with longer tailpieces and screws, check that the stile can hold the 2-1/8-inch bore, and set the strike for the extra door thickness so the bolt lands cleanly.
• A man in Crafton keeps a table saw and a bench full of tools in a detached garage with a glass-panel side door. Nobody sleeps there, and a roll-up door offers a second way out. A double cylinder deadbolt fits well. We install it on a box strike, key it to match his house key, and he carries the key on his ring with a spare kept in the kitchen.
• A seller in Mentone learns during escrow that the buyer's inspector flagged the double cylinder on the front door as a safety concern. The key has been missing for years. We replace the lock with a single-cylinder deadbolt of the same brand, rekey it to match the garage entry, and give the agent a short note of what changed. The sale carries on without the issue.

How the visit works

1. Talk through the door and the reason. We begin by listening: what happened or what worries you, how the household uses the door, who lives there. Break-in history, kids, older relatives and guests all matter. Then we give an honest arrival estimate and explain what we'll check when we get there.
2. Check exits, glass and the people involved. We measure how far the glass is from the lock, test whether a hand could reach it, and note who uses the door. That tells us whether the double cylinder really adds security or only adds risk. You get a plain recommendation and the reasoning behind it.
3. Measure, quote and choose the hardware. We measure door thickness, backset and stile width, then pick a deadbolt that fits: standard thickness, a thick-door kit or a narrow-stile alternative. You see grade and finish options and get a quote before any hole is drilled.
4. Prepare the door. We use a drill jig to cut the face and edge bores square, protecting the glass and finish with tape and padding. If the door is already bored, we clean and check the holes. A crooked bore makes the key bind, so we take care here.
5. Fit both cylinders, key them and set the strike. The two cylinders are tightened evenly, the bolt is adjusted for the backset and the keying is matched to your existing key or a new one. A heavy strike goes into the jamb, and we check the hinge side, because glass doors often give way at the hinges.
6. Test the lock and plan the key. The visit ends with an actual drill: door locked, key at the planned spot, you walking from the far side of the room. If that feels slow, we rethink the plan or the lock. We hand over keys and note the keyway and brand for your records.

How we quote the job

• Lock grade and brand. Fewer models are made in double cylinder form than single, so the selection is narrower. Kwikset, Schlage and heavier commercial lines all offer them. Grade and finish drive cost, and restricted-key models from Medeco or Mul-T-Lock rise further. We tell you what is in stock before we quote.
• Keys and keying. One key operates both cylinders, so keying is simple. Matching your existing keys adds a few minutes. Extra copies, spare keys for other household members and restricted-key blanks each add a small amount. We confirm the count before pinning, and you choose how many.
• Number of doors and scheduling. Costs scale with doors. A single workshop door is a simple job, while four doors across a property with a shared key plan take longer but share the setup. Give us the full list on the first call and we'll quote it as one visit.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Mentone.

Common errors that cost time and money

• Installing one in a rental without telling the landlord. Leases usually restrict lock changes, and a double cylinder raises exit-safety concerns for the owner. Tenants may be asked to remove it at their own cost. Ask in writing, and propose a heavier strike or protected glass instead.
• Leaving the key in the lock all day. It feels safe because you can always get out, but a key in the interior cylinder can be turned by anyone who breaks the glass and reaches in. If the key lives in the lock, you've paid for a double cylinder and kept the weakness.
• Putting a double cylinder on the main exit and hiding the key far away. In a fire, that costs seconds nobody has. Households do it because a pane of glass worries them. Protect the glass instead and keep a normal thumbturn on the door your family relies on to leave.

What to do before we arrive

• Review the setup every year. Kids grow, guests come and go, and keys get moved. Walk through the exit drill again, check that the spare still works and make sure the key hook is where you left it. A small annual check keeps the lock from turning into a hazard.
• Check your insurance and local rules before installing. Policies, leases and HOA rules differ, and we can't speak for your carrier. A short call to your insurer and to the local building or fire department can prevent trouble at renewal, at inspection or when you sell the house.
• Tell every adult in the household, and any regular visitors, where the key lives. A babysitter, a house guest or an older relative who has never seen the lock should be shown on arrival. A note taped inside a cabinet door can help, as long as it isn't visible from outside.
• Practice getting out. With the door locked, walk from the farthest room to the door in the dark and use the key. Do it with children and guests too. If it takes more than a moment, rethink the plan or the lock. Repeat the drill whenever the household changes.

Service in Mentone

Mentone is about 20 miles from our San Bernardino base, roughly 27 minutes in light traffic via I-215 South to SR-210 East through Highland, exit San Bernardino Avenue in Redlands. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Homes and businesses just off SR-210 are routine stops for us. Give the suite or unit number and any gate instructions, and say whether the van can park out front or should pull into a side lot.

About Mentone: Seven Oaks Dam, a 550-foot earth and rock embankment built by the U.S. Army Corps of Engineers between 1993 and 2000, holds back Santa Ana River floods in the canyon above Mentone.

New or replacement locks in Mentone?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.