Residential Lock Installation in Irvine: Every Door, One Key

How this works in Irvine

Keys are where a house full of new locks either comes together or falls apart. For one key to open every exterior lock, the cylinders have to share a keyway, so mixing a Kwikset deadbolt with a Schlage handleset means two keys unless one gets a compatible cylinder. During residential lock installation we standardize on one keyway, then pin every exterior cylinder to the same combination, either a fresh one or the key you already carry. Interior privacy and passage sets take no keys at all, which is a feature: fewer keyed doors inside means fewer locked-out-of-the-bedroom calls. A few homes need more than keyed alike. An accessory dwelling unit behind the main house usually wants its own key for the occupant while the owner's key opens both, a small master arrangement we can build with standard cylinders. A home office or storage closet might get a different key from the rest of the house. And if you want key control, so copies can't be cut at a hardware store counter, a restricted keyway from a line such as Medeco or Mul-T-Lock is an option for the exterior doors. We lay out those choices before pinning anything.

Work included on a typical visit

• Interior privacy, passage and closet hardware. A keyed lock on an interior door is sometimes the right call: a home office, a room rented to a housemate, a closet holding medication or firearms. Those doors want an entrance-function lever or a keyed deadbolt, keyed differently from the exterior. We'll gently argue against keyed locks on young kids' bedrooms, where they mostly produce frustration and butter-knife repairs.
• Boring and prep on new or undrilled doors. When an old door has holes in the wrong places, from a previous handleset or a lock that sat higher, we deal with them before installing. Options include a glued wood plug and paint, a hardwood dutchman on a stained door, or a decorative wrap plate. Leaving old holes open weakens the edge and looks careless on a finished door.
• Strike, jamb and hinge reinforcement. Hinges are the other half of a sound door. If the top hinge has short screws, the door sags, the latch rubs and the deadbolt starts needing a lift before it locks. We swap at least one screw per hinge leaf for a long one into the stud, which pulls the door back into line and keeps the new hardware aligned.
• Installing hardware you've already bought. Many boxed sets come with three or four random keys and no two boxes alike. Our work isn't finished when the hardware is on the door; it's finished when one key runs every exterior cylinder and the spare copies are cut. If a brand uses a cylinder we can't rekey on site, we'll tell you before you buy more of it.
• Gate, shed and outbuilding locks. Side gates usually close with a gravity latch that anyone can lift from the street side. We install keyed gate locks or lockable latches made for wood and metal gates, keyed to your house key where the hardware allows, and set them to catch without slamming. A gate that closes and latches on its own is safer around pools and dogs.

How Irvine shapes the job

In gated and HOA communities, the exterior look of your front door may fall under architectural guidelines, sometimes down to the hardware finish. Check the rules before switching to matte black or brass on doors visible from the street. Interior hardware and garage entry locks are usually your call. We install to the approved finish and can key your own side gate to the house key.

Townhomes and condos bring shared walls, rated doors into common garages and HOA rules about the front of your unit. The door from a shared or attached garage into your living space may be a fire-rated door, and adding a deadbolt or changing hardware should respect that. Inside the unit, residential lock installation works like any house: privacy sets, passage latches and one finish throughout.

Newer tract homes arrive with builder-grade locks, sometimes keyed in ways the construction crews could still use. Buyers in newer neighborhoods of Irvine commonly replace the whole set with heavier deadbolts and matched levers, or keep the hardware and rekey it. Builder doors tend to be consistent in size, which makes a full residential lock installation predictable, though the stock strikes almost always need longer screws.

Situations this covers

• Say an adult daughter is moving her father, who has arthritis in both hands, into the spare bedroom off the hall. Round knobs on the bathroom, his room and the front door are the daily problem. A practical install would be lever privacy sets inside, a lever and keypad deadbolt at the entry so he never fumbles keys, and a front strike adjusted so the door closes without a hard push.
• Say a family adopts a large dog who learns to paw down the back door lever within a week and lets himself out to chase the neighbor's cat. Swapping that one door to a knob, or adding a deadbolt the family throws when they leave, settles it. We'd keep levers on the other doors for convenience, match the knob's finish to the rest of the house and key the new deadbolt alike.
• A typical call from an older neighborhood: a 1962 ranch house where the original knobs are finally giving out. Halfway through the walk-through, it turns out the front door has a 2-3/4 inch backset while the hall doors are 2-3/8, and one bedroom hides an old mortise latch behind a newer rosette. We'd use adjustable latches where they fit, cover the mortise pocket with a retrofit plate, and quote the extra parts before continuing.
• For instance, a two-year-old who has just learned to press the bathroom lock button, and parents tired of fishing with a butter knife. We'd swap the bathroom and bedroom sets for privacy levers with a simple outside release, leave the release tools on top of the door casings where adults can reach them, and, if asked, add a high slide bolt to the laundry room where cleaning supplies live.

From your call to the finished job

1. Walk the house and list every door. We start by walking the property with you and listing every opening: exterior doors, garage entry, patio doors, interior rooms, closets and gates. For each one we note what it needs to do, whether that's lock with a key, lock from inside only, latch without locking, or simply stay closed. That list becomes the order.
2. Measure doors and check the existing prep. Each door gets measured for thickness, backset, bore size and handing, and we look at the existing strike and edge prep. Most interior doors are 1-3/8 inch with a 2-3/8 inch backset, while exterior doors are usually 1-3/4 inch. Anything outside those sizes changes which hardware will fit.
3. Choose hardware, finish and the key plan. We'll suggest where spending more pays off, usually the exterior deadbolts and the front entry, and where economy hardware is fine, such as closets and hall doors. You get a written quote listing hardware and labor separately, so you can switch a finish or a brand without redoing the whole estimate.
4. Prep the doors and mount the hardware. Installation goes door by door. We bore or enlarge holes with a jig where needed, chisel latch and strike mortises to the right depth, and mount the hardware square to the door. Strikes on exterior doors get 3-inch screws into the framing. Old holes are filled or covered before the new trim goes on.
5. Key alike, adjust and test every door. Testing includes the inside. Privacy sets must release from the hallway with the emergency tool, and exterior doors must open from inside with a simple turn, no key needed, unless you've knowingly chosen a double-cylinder deadbolt. We adjust strikes until every door closes quietly and locks without a push.
6. Hand over keys and paperwork. A key log is worth keeping, especially for landlords and households with helpers. We'll note how many keys were cut and who received them. If you ever lose track, the cylinders we installed can be rekeyed without new hardware, which costs far less than starting over.

How we quote the job

• Hardware tier and who supplies it. Supplying your own hardware lowers the parts cost but doesn't change the labor, and returns are yours to handle if something doesn't fit. Buying through us means we check fit before ordering and handle any exchange. Either way, we quote before drilling, and the number doesn't move without your approval.
• Door prep and repairs. Prep moves the price more than most homeowners expect. Converting a door from a single knob to a handleset plus deadbolt can mean a second bore, a new edge mortise and fresh strike work on the jamb. Swapping the same lock style into existing holes is a much smaller job by comparison.
• Scheduling and distance. We're a mobile service based in San Bernardino, so travel distance to Irvine is part of the quote. Our hours run every day, 6:30 a.m. to 11:30 p.m. Booking a whole-house job early in the day leaves room to finish in one visit.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Irvine.

Mistakes to avoid

• Mixing brands on exterior doors. A Schlage deadbolt in front and a Kwikset set on the garage entry means carrying two keys forever, unless one cylinder gets swapped. Choosing one keyway at the start costs nothing and makes keying the house alike simple.
• Installing a double-cylinder deadbolt on the main exit without thinking about fire. If the key isn't in the lock or hanging right beside the door, anyone inside has to find it in smoke and darkness to get out. Use one only with a clear plan, and never on a bedroom exit.
• Reusing the short strike screws that come in many boxes. Those screws only grab the thin jamb, which is why so many kicked-in doors leave the deadbolt intact and the jamb split in two. Strike screws should reach through the jamb and shims into the framing behind it.

Advice before you book

• Test every lock from inside as well as outside after any installation. Can a child open the front door in an emergency? Can a guest get out of the bathroom if the button sticks? A door that's secure from outside but awkward to exit is the wrong install, however good it looks.
• Choose finishes for the climate. On a sunny south- or west-facing door in Irvine, living finishes and cheap plated coatings fade and spot within a few summers. PVD or lifetime finishes cost more but hold their color. Interior doors are sheltered and can wear any finish you like.
• Check how your doors swing before ordering levers. Most modern levers are reversible, but some designer and handleset models are handed. Stand outside the door facing it: if the hinges are on your left, it's a left-hand door. Write the handing next to each door on your list.
• If you rent out the house, a room or an ADU, insist on rekeyable cylinders. Standard pinned cylinders can be rekeyed between occupants without replacing any hardware, so a tenant change means a short visit instead of a new set of locks. Keep the key plan written down with the property records.

Getting to Irvine

Irvine is about 58 miles from our San Bernardino base, roughly 62 minutes in light traffic via I-215 South to SR-91 West in Riverside, SR-91 West through Corona and Santa Ana Canyon. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Our path into Irvine depends on where the previous job wrapped up. Sometimes that's a straight run via Portola Parkway; other times it's surface streets the whole way. Either way, you get a heads-up call when the technician is close.

About Irvine: Irvine annexed the former Marine Corps Air Station El Toro in late 2003, adding about 7.3 square miles that now hold the Orange County Great Park and new neighborhoods.

New or replacement locks in Irvine?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.