Replacing the Locks on Your Irvine House, Door by Door

What to know first in Irvine

The smartest house lock replacement isn't always the one that replaces the most locks. We look at each lock and sort it into one of three groups. Replace: hardware that is worn, damaged, discontinued, light-duty on a key entry door, or in a style or finish you want gone. Rekey: hardware in good working order that only needs new keys. Repair or adjust: a sound lock fighting a sagging door or a shifted strike. Exterior entry doors come first, since those are what keep people out. The garage entry door and slider deserve special attention because they're often overlooked. Interior hardware can be done the same day or saved for later, depending on budget. Planning it this way keeps the total in line with what actually needs doing, and you still end up with one key for every exterior lock. We'll explain why each lock lands in its group, and you decide. If you'd rather replace everything for a uniform look, that's a perfectly good reason, and we'll quote it that way.

Work included on a typical visit

• Exterior entry doors keyed alike. Exterior doors are the priority in any house lock replacement. We match each door's bore and backset, install Grade 1 or Grade 2 deadbolts, and set each strike so the bolt slides in easily. A door that needs a shove to lock gets adjusted first.
• Garage-to-house door and garage side door. Burglars like garages because they're out of sight once the overhead door is open. If your garage entry door has only a knob lock, we add a deadbolt during the house lock replacement, reinforce the strike, and make sure the door still swings shut and latches by itself.
• Sliders, French doors and other back-of-house openings. The back of the house is often its soft side, with a sliding patio door, French doors or a rear slider that was never given much of a lock. We replace worn hooks and flush bolts, align the doors so they latch fully, and add a secondary bar or pin where the factory lock is light.
• Side gates, sheds and outbuildings. Sheds, workshops and casitas often hold expensive tools behind a flimsy padlock and hasp. We replace them with sturdier ones, fit a keyed lock where the door allows it, and key what we can to the house so the ring in your pocket gets shorter.
• Interior passage and privacy sets to match. A house lock replacement can include interior doors so every handle in the house matches. We replace bedroom and bathroom privacy locks, closet passage sets and dummy pulls in the same finish and style as the exterior hardware, using the bores already in each door.

How Irvine shapes the job

Large homes in Irvine can have fifteen or twenty openings, including pivot doors, double entries, a guest house and a pool gate. A whole-house lock replacement here is a planning exercise: which openings need high-security cylinders, which need a master key arrangement for staff, and which finishes match custom hardware. We prepare a written key plan, order restricted keyways where wanted and install door by door, so the property ends up with a coherent system rather than a ring of keys.

Houses near campus in Irvine often hold several roommates, each with a key, and turnover that never matches the lease year. For landlords, a whole-house lock replacement between tenants is the cleanest reset: new exterior locks, rekeyed bedroom locks and a log of who holds keys. Tenants should check the lease and ask the landlord before changing anything. We install bedroom locks with proper outside releases and keep the key plan simple enough to hand over.

In commuter neighborhoods around Irvine, houses sit empty for long stretches while everyone is on the road. That makes the quiet doors matter: the garage entry, the side gate and the back slider are all out of sight during the day. A house lock replacement should cover every entry, with keypad or smart options on the doors you use while rushing in and out, plus reliable mechanical backups. We plan the visit around your schedule and our 6:30 a.m. to 11:30 p.m. hours.

Example situations

• For example, a couple closing on a house near Irvine Valley College receives a ring of a dozen keys from the previous owner and no idea who else has copies. We walk the property, count eight locks including the side gate and the shed, replace the two worn knobs, rekey the good deadbolts and pin everything to one key. They move in with a single key and a short list of what's on each door.
• A 1960s ranch near San Joaquin Wildlife Sanctuary has an original brass front knob, a back-door deadbolt from the 1990s, a garage entry lock of unknown age and a gate padlock nobody remembers buying. Four brands and five keys. We sort them, replace two, rekey the deadbolts and fit a padlock that takes the house key. The key ring drops from five keys to one.
• A homeowner's former partner left with keys to the front door, the back door and the garage entry. Rekeying only the front door would have solved a third of the problem. We replace the garage entry lock, which was already loose, rekey the rest and test every key on every door. Only the new key opens anything now.
• A homeowner adds a pool and wants the back yard gate and the patio slider to be hard for small children to open. We fit a self-latching gate latch mounted high, replace the slider lock and add a high secondary latch, then key the gate to the house. Pool barrier rules are set locally, so we suggest confirming details with the building department.

From your call to the finished job

1. Tell us how many doors and why. When you call, tell us roughly how many doors are involved and why you want them changed: a move, a break-in, worn hardware, a remodel. A rough count is fine, because the walk-through usually finds more. We give an honest arrival estimate for Irvine and tell you what to gather beforehand.
2. Verify you live at or own the house. Our license is LCO7891 from the Bureau of Security and Investigative Services, and you can check it at search.dca.ca.gov. California's Locksmith Act is the law behind it. We ask for ID, confirm ownership or residency, and then begin the walk-through.
3. Walk the property and build the plan. This step keeps whole-house jobs from getting messy. By the end of the walk-through you know the count, the condition and the recommended action for every lock. If a door is unusual, we tell you what we'd need to order before promising a one-visit finish.
4. Approve one quote for the whole job. We don't start with a vague number and adjust upward. After the walk-through, the quote is firm for the work listed. If we find something hidden behind a door, such as rotted framing, we stop and discuss it with you before adding anything.
5. Work exterior first, then the rest. Where a door needs adjusting, we do it as part of this step: easing a strike, resetting a hinge, trimming a sticky edge. A lock that lines up with its strike lasts longer, and the doors close without the shove many owners have learned to live with.
6. Key everything alike, test it and leave a record. Once the hardware is in, we pin the cylinders to one key, then try every key in every lock, from both sides, several times. Anything that sticks gets fixed before we leave. You get a full set of keys and the old hardware if you'd like it.

What affects the cost

• How many locks, and how many are replaced versus rekeyed. The count is the largest factor, and the split matters. Replacing a lock costs more than rekeying one, so a house where most hardware is sound costs less than one where everything is worn. We sort every lock at the walk-through and price each choice separately.
• Special openings: sliders, French doors and gates. Not every opening uses a standard bored lock. Slider latches, multipoint French door locks and outdoor gate hardware are separate products with their own prices, and some need adjustment of the door or gate as well. We list them separately from the standard doors.
• One visit versus phased work, and timing. Distance from our San Bernardino base is part of the quote, and a larger house job needs more time on site. Sharing the door count when you call helps us book enough time, so the work finishes the same day instead of spilling over.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Irvine.

What not to do

• Forgetting the quiet doors. The garage entry, the garage side door, the slider and the side gate are where old keys keep working long after the front door is fixed. A whole-house job should list every opening before anyone buys a single lock.
• Replacing every lock by default. A house lock replacement doesn't mean tossing hardware that still works. A sound Grade 1 deadbolt only needs new keys. Replace what's worn, damaged or weak, rekey the rest, and put the savings toward reinforcement or a better garage entry lock.
• Changing locks one door at a time over a long stretch. Meanwhile an old key still opens whichever doors haven't been done. If you must phase the work, do the exterior doors in one visit and rekey the rest to the same key right away.

What to do before we arrive

• Pick one finish for the exterior doors before you choose styles. Satin nickel, matte black and oil-rubbed bronze are common choices, and mixing them looks accidental. Judge them from one spot where the front door, porch light and garage are all visible at once.
• Photograph each door's new lock and store the images with the receipt. If you later need a matching lock for an addition, a repair or an insurance conversation, you'll know the brand, model and finish without hunting for them. Add a note of which key fits which door.
• Think about the garage. Its entry door gets the least attention and the most traffic, and a forgotten side-door lock or a shared keypad code is a common weak point. Include them in any lock job, and change the keypad code if one is used.
• Do the exterior doors first if you must phase the work. Front, back, garage entry and slider protect the house; interior passage sets mostly affect looks and comfort. Doing the entries first, and keying them alike, buys the most security for the first money spent.

Reaching Irvine

Irvine is about 58 miles from our San Bernardino base, roughly 62 minutes in light traffic via I-215 South to SR-91 West in Riverside, SR-91 West through Corona and Santa Ana Canyon. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Commercial jobs on busy stretches like I-5 sometimes need a parking plan, especially for storefront doors or roll-up gates. Let us know about loading zones, red curbs or parking structures before we arrive.

About Irvine: The city is named for James Irvine, whose family's Irvine Ranch once stretched from the Pacific coast to the Santa Ana Mountains.

New or replacement locks in Irvine?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.