Planning New Lock Installation in Irvine? Start Here

What to know first in Irvine

Timing decides how good the finished job looks. Drywall dust gets into latch mechanisms, paint fills strike mortises and glues faceplates to door edges, and new flooring changes the gap under a door that's already hung. So we prefer to install after paint and flooring, then return for touch-ups if needed. Codes matter too. Building codes expect a home's required exit door to open from the inside without a key or special effort, which rules out some keyed-both-sides arrangements. The door between an attached garage and the house is expected to be solid or rated and to close on its own. Accessible commercial spaces call for hardware operable with one hand and no tight grasping or twisting, which is why levers dominate. California rental dwellings need working deadbolts on main entry doors. A new building also keeps moving: framing dries, doors swell and shrink, and strikes that lined up in March can drift by fall. We plan a quick check for that settling period instead of calling it a defect.

Work included on a typical visit

• Builder-grade hardware swaps before move-in. Production builders buy thousands of identical sets, so tract homes in Irvine often come with plain knobs and thin plating that wear quickly. We replace them with Grade 2 or Grade 1 deadbolts and levers before you move in, match the finish on every door and key the exterior locks alike.
• Locks for remodels, additions and new door slabs. Additions bring doors nobody planned for: French doors to a patio, a pocket door to a new bath, a side entry off the laundry. We list each opening, pick a function, and reinforce the framing behind the strike while walls are still easy to reach, then install once painting is done.
• Keying plans designed from scratch. Every lock in a keyed-alike group has to share a keyway. A Kwikset deadbolt and a Schlage handleset won't share a key unless a cylinder is swapped. We standardize on one brand or specify cylinders that fit, so a single key works across the doors that should share it.
• Gates, sheds, workshops and new outbuildings. Gates are a distinct job: pedestrian latches, drop rods on double drive gates, key switches for electric openers. We match the lock's throw to the frame and key it with your house when possible. Motorized gate controls belong to the gate installer, and we coordinate with them.
• Added locks on windows and sliding doors. New lock installation isn't only about swinging doors. Sliding glass doors often ship with a small latch a screwdriver can defeat, and many windows have only a thumb latch. We add pin locks, secondary bolts or track bars, chosen to leave the door usable and the window openable for emergency exit.

What's different about Irvine

New multifamily buildings and unit renovations in Irvine need hardware that handles hard use: Grade 1 or Grade 2 deadbolts, durable levers and a key structure that lets managers rekey at turnover without replacing anything. We recommend interchangeable cores or rekeyable cylinders, a master for the manager and a clear chart. Fire-rated unit doors and corridor doors have specific hardware requirements, and we install listed parts that preserve the rating.

Gated communities usually come with architectural guidelines covering what you can change on the street side of the house. Front-door hardware, finish and sometimes the style of lever or handleset may need approval before you buy. Send the committee a model number and a photo, wait for a written yes, then call us. Guard houses add a step: give us the visitor details in advance so we're expected at the gate when we reach Irvine.

Large custom homes tend to have far more openings than the plan suggests: guest wings, wine rooms, offices, pool houses, service entries and gates. New lock installation here starts with a thorough schedule and a key system with real structure, often a master with sub-masters by wing. Thick solid doors may need extension kits or mortise locks, and finishes must match the architectural hardware. Restricted keyways stop copies from being cut without authorization.

Common situations

• For example, a landlord completes a new duplex in Northwood. Each unit needs its own key group, the shared laundry needs a third, and the owner wants one master key that opens everything. We'd lay out a simple master-keyed system, pin every cylinder, and give the owner a chart. Tenant keys won't open the neighbor's front door, and the master stays with the owner.
• A typical rural example: a new steel workshop sits at the back of a property off Culver Drive, with a man door and an overhead door. The owner wants a deadbolt, a shrouded padlock on the roll-up door's side latch, and one key that also fits the barn gate. We'd bolt hardware through the steel instead of trusting thin screws, and key every lock into the same system.
• Say a café is opening in a shopping center off Irvine Center Drive. The lease gives the tenant access shortly before opening day, and the contractor still has trim painting to finish. We'd walk the suite, order a storefront deadlock, a back-door deadbolt and a lever for the restroom, install the week the painters leave, and hand the owner keys once the inspector signs off.
• Picture a homeowner building a family room addition onto the back of a 1980s house. The framers leave a pair of French doors with an inactive leaf and no flush bolts. A good plan settles hardware before the doors are painted: flush bolts for the inactive leaf, a keyed deadbolt on the active leaf, solid blocking behind the strike, and a keying plan that matches the front door.

How the visit works

1. Tell us what's new and when it's due. Call (951) 903-3193 and describe the project: new build, remodel, addition, ADU or business suite. Tell us how many doors, who else is working on site and when you need to move in or open. Plans, a door schedule or a handful of phone photos all help us get started.
2. Build the door and key schedule. We list every opening with a number, location, door material and thickness, swing, glass near the latch and the function needed. Next to that go the finish and the key group. It can start from your photos and finish with a quick site visit, then becomes the ordering list and the checklist.
3. Order, check and stage the hardware. Once you approve the schedule, we order from one source so finishes and keyways match. Lead times vary for special finishes and commercial hardware, and we tell you the real number before you commit. When boxes arrive, we open each, confirm the model and parts, and stage them by door number.
4. Install after the messy trades finish. We schedule the install after paint, flooring and drywall are done, so finishes stay clean. Each door gets bored or checked, the faceplate mortised, the strike set into solid framing and the hardware mounted. We mask finishes, vacuum shavings as we go and leave nothing on the floor.
5. Key, test and tune every opening. Cylinders are pinned on site to the plan you approved. Then every key is tried in every lock it should open, and in every lock it should not. We cycle each latch and bolt with the door closed, check the exit from the inside, and adjust until it works with a finger, not a shoulder.
6. Hand over keys, records and a settling-in check. Before we pack up, we walk the property with you: demonstrate each lock, show where the emergency releases are and explain how to add or cancel keys later. If a contractor or property manager needs keys, we hand them over in a separate, labeled set.

What affects the cost

• Number of openings and their functions. We price each opening on the schedule so you can see where the money goes. If the budget needs trimming, you can decide door by door: sturdier hardware on the exteriors, standard sets inside, and anything you can postpone left for later.
• Hardware tier, finish and who supplies it. Grade matters more than price tags suggest. Grade 1 hardware tolerates heavy use and abuse, while Grade 3 suits a closet door and little else. We recommend the grade by location: strongest on exterior doors, solid mid-grade on busy interior doors, basic where a door rarely moves.
• Key plan: alike, separate or master. Extra keys cost little when cut at the time of pinning and more when ordered later from a code. Decide the count up front. Keys for a contractor, a cleaner, a property manager and an emergency set at a neighbor's house add up faster than anyone expects.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Irvine.

What to do before we arrive

• Store the key record somewhere better than a kitchen drawer. A photo on your phone and a copy with your home papers is enough. Don't write the key code on the key itself or on a tag that travels with it, because anyone who finds it can cut a copy.
• Test your exit routes yourself. Every exterior door should open from inside with one motion and no key, including the garage entry and the patio door. If anyone in the house struggles with a knob or a thumb turn, tell us before installation so we can choose differently.
• Schedule the install after painting and flooring are done but before furniture, appliances and boxes crowd the doors. That window lets us work freely, protect finishes and test every door closed. If painting has to finish after, mask the hardware so paint doesn't harden in the latch.
• Check handing before opening any boxes. Stand outside the door, note the hinge side and swing, and compare them with the box label. Some levers and mortise sets are handed and can't be flipped. A label reading right hand on a left-hand door means a return.

What not to do

• Installing locks before the painters finish. Paint fills strike mortises, glues faceplates to door edges and hardens inside latches. Scraping it off damages finishes and wears mechanisms. Either schedule hardware afterward or remove and bag every piece before painting starts.
• Skipping the pre-wire. Deciding on a keypad, access reader or electric strike after drywall means fishing cable through finished walls or patching them. A pull string and a short conduit run before the walls close cost almost nothing and leave every future choice open.
• Mixing brands and finishes across the same group of doors. Two satin nickel sets from different manufacturers rarely match exactly, and two keyways mean two keys. Choosing one platform and one finish gives a tidy result and a simpler key ring. A single order from a single source helps.

Getting to Irvine

Irvine is about 58 miles from our San Bernardino base, roughly 62 minutes in light traffic via I-215 South to SR-91 West in Riverside, SR-91 West through Corona and Santa Ana Canyon. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Once the evening commute thins out on SR-133, drive times usually shrink. That makes an evening call before closing a practical option for non-urgent jobs that you couldn't fit into the workday.

About Irvine: Irvine Station on Barranca Parkway is served by Metrolink's Orange County and Inland Empire-Orange County lines and by Amtrak's Pacific Surfliner.

New or replacement locks in Irvine?

Call (951) 903-3193 and tell us which doors and what kind of hardware you have in mind. If you already bought the lock, keep the box handy so we can check it fits the door, and we'll quote the install before any work starts.