Rekey Door Locks in Irvine Without Replacing Hardware

How this works in Irvine

Each kind of door hardware hides its cylinder in a different spot, and that drives how long the job takes. A deadbolt is the simplest: two screws release the interior thumbturn and the exterior cylinder slides out. Knobs and levers use a small release catch, and the cylinder comes out of the knob body. On a handleset, the key almost always lives in the deadbolt section above the grip, while the thumb latch below has no cylinder at all. Older front doors with mortise locks use a threaded cylinder held by a set screw on the edge of the door, and that screw is sometimes buried under decades of paint. Rim cylinders, common on gate locks and some older back doors, come out from the inside with two long screws. French doors and many fiberglass entry doors with multipoint locks use euro profile cylinders, which we normally replace with a new cylinder keyed to match rather than re-pin. Patio sliders and storm doors are the wild cards: many use inexpensive wafer locks that can't be re-pinned, so we swap in a better lock or add a secondary one.

Work included on a typical visit

• Knob and lever entry locks. Levers take far more force than knobs, and on busy doors the spring cassette inside eventually weakens, leaving a lever that droops. Rekeying won't fix that. If a lever on a door you want rekeyed is sagging, we may suggest replacing that one handle and keying it to match, while re-pinning the healthy locks elsewhere in the house.
• Handlesets and gripsets. On a typical handleset, the grip and thumb latch below are only for opening the door; the key works the deadbolt section on top. So rekeying a handleset usually involves one cylinder, not two. We remove the interior trim, slide out the deadbolt cylinder, re-pin it and confirm the thumb latch still releases smoothly afterward.
• Garage entry and garage side doors. The door between the garage and the house matters more than people think. Many households leave the overhead door up while they're in the yard or driveway, which makes that inner door a front door in practice. We rekey its knob and deadbolt to the house key and check that the door still closes and latches on its own.
• Security screen and storm doors. Storm doors use lighter latch hardware with a small keyed handle, often a wafer lock that can't be re-pinned. If the storm door needs to be on your key, we look for a keyed replacement handle that fits the door's hole pattern. If not, many owners simply leave the storm door unkeyed and rely on the entry door behind it.
• Kwikset SmartKey locks. Matching SmartKey locks to your other doors is simple when everything in the house is Kwikset, since they share a keyway. The challenge is a house with SmartKey on some doors and Schlage on others. We can key the Kwikset doors together and replace the odd ones out, or swap hardware so a single key covers everything.

Local factors in Irvine

Busy family homes tend to have keys scattered everywhere: grandparents, babysitters, carpool neighbors, a teenager who lost theirs twice. Rekeying resets all of that in one visit. Many families key the front, back and garage entry alike for simplicity, then give older kids and helpers a keypad code instead of a metal key, so access can be removed later without paying for another rekey.

Apartment door locks follow the lease. Renters should get the landlord's written approval before any door is rekeyed, and many leases require giving management a copy of the key. Landlords handling a turnover usually want the entry deadbolt and knob rekeyed while mailbox and common-area keys stay with management. We'll rekey door locks inside the unit, cut keys for both tenant and owner, and note the change for your records.

Condos and townhomes often split responsibility: the owner controls the unit's entry door, while the HOA handles common doors, pool gates and garage gates. Before we rekey door locks on a condo, glance at your CC&Rs for rules on exterior hardware finishes or management key access. Most allow rekeying without fuss since nothing visible changes. An attached garage with an interior door into the unit deserves its own lock check too.

Situations this covers

• For example, a homeowner off Jamboree Road asks us to rekey door locks including the patio slider, whose key went missing years ago. On inspection, the slider's cylinder is a wafer design that can't be re-pinned. Rather than charging for a pointless attempt, we'd show them why, then offer a keyed replacement that fits the slider's cutout or a sturdy foot lock that secures it from inside.
• A typical ADU setup: a converted garage behind a house in Irvine now has its own entry door with a lever and a deadbolt. The owners rent it to a relative and want their house key to open it, but they don't want the ADU key opening the main house. We'd explain a small master key arrangement, pin the ADU door accordingly, and write down which keys go to whom.
• For example, a homeowner realizes the steel security screen door has a key nobody has seen in a decade, so the screen just stays unlocked. We'd pick or decode the screen door cylinder, then check whether it accepts the house keyway. If it does, it gets re-pinned to the house key. If it's a proprietary cylinder, we'd quote a compatible replacement before doing anything else.
• Say the front door wears a Schlage Encode while the back and garage doors still have their original Kwikset knobs and deadbolts. The owner wants one key. Because the brands use different keyways, we'd re-pin the Encode's Schlage cylinder, replace the Kwikset hardware on the other doors with Schlage keyed to match, and then reset the Encode's codes and app users as a separate step.

Step by step with Julian's Locksmith

1. Tell us which doors and what's on them. Call (951) 903-3193 and list the doors you want rekeyed: front, back, garage entry, side door, slider, screen, gate. Tell us the brand if you can read it on the latch face or a key head. Kwikset, Schlage and other makers take different parts, so the more we know, the better stocked we arrive.
2. Confirm you're authorized. Verification protects you more than it protects us. The same rule that has you showing ID also stops a stranger from having your locks rekeyed while you're at work. It takes a minute, and we do it every time, including for a single-door job on a quiet afternoon.
3. Check each door before touching the lock. This is also when we confirm which locks can be rekeyed and which can't. A cheap slider cylinder, a worn-out knob or a proprietary smart lock cylinder gets flagged now, with options and prices, so nothing changes once we're halfway through the house.
4. Re-pin each cylinder, one door at a time. While each plug is out, we clean old graphite, dust and grit from the cylinder, check the springs and replace any that are weak or rusted. A rekeyed lock should feel smoother than it did before we arrived. If it doesn't, we keep working on it until it does.
5. Test from both sides. Smart locks get an extra round of checks. We confirm the motor still throws the bolt fully after the cylinder goes back in, then run the keypad or app once more. A rekey should never leave a smart lock half-working or out of calibration.
6. Hand over keys and a door list. You get the agreed number of keys, and we suggest counting them in front of us. We also leave a simple list of which doors take which key, useful later when a cleaner, contractor or relative asks for access and you need to decide what to hand over.

What affects the cost

• What kind of hardware each door has. Labor rises with how a cylinder is mounted, not with how expensive the lock looks. A plain Kwikset deadbolt and a polished Baldwin deadbolt re-pin in much the same way, but a painted-in mortise cylinder or a smart lock that has to be unmounted first takes noticeably more time.
• Whether you have working keys. A working key for each door makes rekeying faster, because the plug can be turned to release the cylinder. Without a key, the lock has to be picked, decoded or occasionally drilled before it can be re-pinned. That extra step is the most common reason a phone quote changes on-site.
• Keys and scheduling. Grouping doors into one visit costs less than rekeying a door now and another next month, because the trip and setup are paid once. If you suspect you'll want the garage or side door done eventually, ask for both prices now and decide with the numbers in front of you.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Irvine.

Advice before you book

• Clear a path to each door, especially the garage entry and the slider. Boxes stacked against a garage door or a couch pushed up to a slider slow the work and make it hard to test the door's swing. Ten minutes of moving things keeps the visit efficient.
• If your deadbolt needs a push or a pull before it turns, say so when you book. That's a door alignment problem rather than a key problem, and it's best fixed while the lock is apart. Left alone, the binding grinds down the new pins exactly as it did the old ones.
• Hold on to the key code or the first key we cut. Copies made from copies drift a little each time, and eventually a duplicate won't turn smoothly. A key cut to the code is accurate, so treat it as your master copy and make future duplicates from it.
• Skip the spray oil before we arrive. Household lubricants leave a film that collects dust in the pins, and a cylinder soaked in oil is messier to re-pin. If a lock is stiff, leave it alone; we'll clean it properly and finish with a dry lubricant made for locks.

Mistakes to avoid

• Hiring whoever answers first from an online listing without checking for a license. California requires locksmith companies to be licensed through BSIS. Ours is LCO7891, and you can confirm it at search.dca.ca.gov. A legitimate locksmith also gives you a price before touching any door.
• Rekeying one door from a keyed-alike group without thinking it through. That door will then need a different key from the rest. That may be exactly what you want, or it may leave you carrying two keys you never asked for. Decide before any pins come out.
• Buying a DIY rekey kit for the wrong brand. Kits are keyway-specific, and the pins, springs and follower in a Kwikset kit won't help with a Schlage cylinder. Even with the right kit, one slipped follower can launch drivers and springs across the floor and leave the door unusable.

Getting to Irvine

Irvine is about 58 miles from our San Bernardino base, roughly 62 minutes in light traffic via I-215 South to SR-91 West in Riverside, SR-91 West through Corona and Santa Ana Canyon. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Rush hour on Portola Parkway can stretch a drive considerably. We'd rather give you a realistic arrival window than an optimistic one, and we'll call you if a closure or a crash changes the plan.

About Irvine: Irvine annexed the former Marine Corps Air Station El Toro in late 2003, adding about 7.3 square miles that now hold the Orange County Great Park and new neighborhoods.

Planning a rekey in Irvine?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.