2010 Mitsubishi Raider Key Replacement

2010 Raider key specs

Raiders with Chrysler's Sentry Key immobilizer use a Philips ID46 key, either a plain transponder key or a three-button remote-head key with lock, unlock and panic. One supplier lists the remote-head key under FCC ID KOBDT04A with a CR2032 battery and an uncut blade that must be matched to the truck. A non-chip version of a key may also exist for trucks built without the immobilizer, so we test your key before cutting a copy.

What's specific to the 2010 Raider

2010 was the final model year of the Raider Dakota-based (single generation). Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2010 Mitsubishi Raider matches a 2006.

A 2010 Mitsubishi Raider is about 16 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2010 Mitsubishi Raider

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2010 Mitsubishi Raider with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Mitsubishi Raider only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.
• Basic mechanical key. A plain mechanical key has no chip and no electronics, just a cut blade that lines up the wafers inside the lock. If your 2010 Mitsubishi Raider uses one, replacement is mostly a cutting job, but how it's cut matters. Copying a worn key copies its wear, and a duplicate of a duplicate drifts further from spec each time. We prefer to cut by code: we look up or decode the factory bitting, then cut a fresh key to the original depths on a code machine. The result turns smoothly in the doors and ignition instead of needing a jiggle. If the ignition wafers themselves are already worn, we'll point that out too.

How the Mitsubishi immobilizer works on the Raider

Mitsubishi's US key history splits into a handful of eras, and the model year usually tells us which one we're dealing with. Around 2000, the larger models got Texas Instruments transponders: the Diamante, Montero and Montero Sport on the MIT1 key, and the Eclipse and Galant on the MIT6 key, with the chip moving from 4D60 to 4D61 around the middle of 2001. Small cars such as the Mirage and the 2002-2007 Lancer generally kept plain cut keys, although the Lancer Evolution did not. Philips ID46 chips appeared on the redesigned 2004 Galant, remote-head keys followed in 2006, and the blade changed from the straight MIT6 to the shouldered MIT3 during the 2007 model year. The 2007 Outlander and 2008 Lancer introduced FAST-key, Mitsubishi's keyless operation system, which carried on through the Lancer Evolution X and the Outlander Sport. Later Mirage, Eclipse Cross and Outlander Sport smart keys are newer designs that need their own tool coverage, and the Nissan-based 2022-on Outlander uses an AES-encrypted fob. The Dodge Dakota-based Raider pickup follows Chrysler's Sentry Key rules instead.

• One supplier lists the KOBDT04A remote-head key for 2006-2009 Raiders.
• Chrysler built the Raider alongside the Dakota at its Warren Truck plant in Michigan.
• Production ended in June 2009, so 2010-model Raiders are rare.

Programming a 2010 Raider key

On Sentry Key trucks, we cut the key by code or by decoding a lock, then program it through the OBD-II port with the four-digit Chrysler PIN, which our tools can usually read. The remote buttons are learned in the same visit. With two working keys, Chrysler's owner routine can often add another. Trucks without the immobilizer just need an accurate cut. All-keys-lost is a routine on-site job.

Lost every key to your Raider?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mitsubishi Raider can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mitsubishi Raider requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your Raider and your schedule.

Raider key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your Raider uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Mitsubishi keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Mitsubishi system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Raider key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Mitsubishi system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mitsubishi key problems

• Inland Empire heat drains fob batteries faster than the calendar suggests. On FAST-key cars, a key warning on the dash or a fob that only works up close usually means a weak CR2032, an easy fix before it strands you.
• Mitsubishi remotes and smart fobs lock to the first vehicle they're programmed to. A used one from a salvage yard or online seller has to be unlocked or reflashed before it will pair, and some newer fobs cannot be reused at all.
• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2010 Mitsubishi Raider key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Raider in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.