2007 Mitsubishi Raider Key Replacement

2007 Raider key specs

Raiders with Chrysler's Sentry Key immobilizer use a Philips ID46 key, either a plain transponder key or a three-button remote-head key with lock, unlock and panic. One supplier lists the remote-head key under FCC ID KOBDT04A with a CR2032 battery and an uncut blade that must be matched to the truck. A non-chip version of a key may also exist for trucks built without the immobilizer, so we test your key before cutting a copy.

What's specific to the 2007 Raider

The 2007 Mitsubishi Raider is the second of 5 model years in the Raider Dakota-based (single generation) (2006–2010), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2007 Mitsubishi Raider is about 19 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2007 Mitsubishi Raider

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Mitsubishi Raider means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Transponder (chip) key. There are two ways to give a new transponder key the right identity. Cloning reads the chip in a working key and writes that same ID onto a special cloneable chip, so the car can't tell the two apart. Programming adds a brand-new key ID to the immobilizer's memory through the OBD-II port, sometimes after entering a security PIN tied to the VIN. Cloning is handy when you have a working key and the chip family supports it. Programming is the better choice when keys are lost, because it also lets us remove keys you no longer control from the car's memory. For your Mitsubishi Raider, we'll explain which method fits and why.
• Basic mechanical key. Before treating a Mitsubishi Raider key as purely mechanical, we confirm it. Some keys look like plain metal with a rubber or plastic head yet hide a transponder inside, and immobilizers arrived on different trims and model years at different times. If yours truly has no chip, the new key is cut and then tested in the doors, ignition, glove box and trunk where those locks exist. Mechanical blades also show up on newer vehicles as valet keys and as the emergency insert tucked inside a smart fob. Those blades still matter: they're how you get in when a fob battery dies, so they deserve the same careful cutting.

How the Mitsubishi immobilizer works on the Raider

Mitsubishi's US key history splits into a handful of eras, and the model year usually tells us which one we're dealing with. Around 2000, the larger models got Texas Instruments transponders: the Diamante, Montero and Montero Sport on the MIT1 key, and the Eclipse and Galant on the MIT6 key, with the chip moving from 4D60 to 4D61 around the middle of 2001. Small cars such as the Mirage and the 2002-2007 Lancer generally kept plain cut keys, although the Lancer Evolution did not. Philips ID46 chips appeared on the redesigned 2004 Galant, remote-head keys followed in 2006, and the blade changed from the straight MIT6 to the shouldered MIT3 during the 2007 model year. The 2007 Outlander and 2008 Lancer introduced FAST-key, Mitsubishi's keyless operation system, which carried on through the Lancer Evolution X and the Outlander Sport. Later Mirage, Eclipse Cross and Outlander Sport smart keys are newer designs that need their own tool coverage, and the Nissan-based 2022-on Outlander uses an AES-encrypted fob. The Dodge Dakota-based Raider pickup follows Chrysler's Sentry Key rules instead.

• One supplier lists the KOBDT04A remote-head key for 2006-2009 Raiders.
• Chrysler built the Raider alongside the Dakota at its Warren Truck plant in Michigan.
• Production ended in June 2009, so 2010-model Raiders are rare.

Programming a 2007 Raider key

On Sentry Key trucks, we cut the key by code or by decoding a lock, then program it through the OBD-II port with the four-digit Chrysler PIN, which our tools can usually read. The remote buttons are learned in the same visit. With two working keys, Chrysler's owner routine can often add another. Trucks without the immobilizer just need an accurate cut. All-keys-lost is a routine on-site job.

Lost every key to your Raider?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Mitsubishi Raider can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mitsubishi Raider requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2007 Mitsubishi Raider we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Raider key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your Raider uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Raider, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Raider key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Raider came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Mitsubishi key problems

• Remote-head keys and smart fobs take different coin cells: the remote-head keys use a thin CR1620, while FAST-key and smart fobs use a CR2032. A cell of the wrong thickness may not make good contact, so read the old battery before buying.
• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.
• The 2007 Outlander used a one-year FAST-key fob, FCC ID OUCG8D-640M-KEY-N, that differs from the OUC644M-KEY-N fob used from 2008 on. Ordering by model name alone often brings the wrong part.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2007 Mitsubishi Raider key?

Need a key for your 2007 Mitsubishi Raider? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.