Mitsubishi Eclipse Key Replacement

Eclipse keys by generation

Fourth-generation Eclipses use a remote-head key: four buttons (lock, unlock, trunk, panic) on top of a blade with a Philips ID46 chip. Cars built through about early 2007 have a straight MIT6 blade, and later cars use a shouldered MIT3 blade, so the 2007 model year can go either way. Both versions carry FCC ID OUCG8D-620M-A, though OUCG8D-625M-A also appears on some 2007-2008 cars, and take a CR1620. A plain ID46 transponder key without buttons is available as a spare. The Spyder, which returned for 2007, uses the same keys. The transponder and the remote buttons are both programmed through the OBD-II port with a programmer and the vehicle PIN, and supplier listings show no owner programming for this remote. Used remote-head keys must be unlocked before reuse. For all-keys-lost, we decode the door lock to cut the right blade, then register at least two keys at the car, which also removes the lost ones.

Third-generation Eclipses and Spyders start with a plastic-head transponder key on the straight MIT6 blade. Supplier references list a Texas 4D60 chip for 2000 and early-2001 builds and a 4D61 chip from mid-2001 through 2005, so we read the chip before cutting. Keyless entry came as a separate remote: a two- or three-button HYQ12ABA unit on 2000-2001 cars and, from 2002, a two-, three- or four-button OUCG8D-525M-A remote. All of these remotes take a CR2032. The Spyder uses the same key and remotes as the coupe. Chip keys are registered through the OBD-II port with a programmer and the immobilizer PIN; the routine erases and relearns every key, so bring all of them. The separate remotes pair on board through a jumper routine at the diagnostic connector. If every key is lost, we decode a lock, cut new MIT6 keys on the right chip blank and register them at the car.

Mitsubishi key security

Mitsubishi's US key history splits into a handful of eras, and the model year usually tells us which one we're dealing with. Around 2000, the larger models got Texas Instruments transponders: the Diamante, Montero and Montero Sport on the MIT1 key, and the Eclipse and Galant on the MIT6 key, with the chip moving from 4D60 to 4D61 around the middle of 2001. Small cars such as the Mirage and the 2002-2007 Lancer generally kept plain cut keys, although the Lancer Evolution did not. Philips ID46 chips appeared on the redesigned 2004 Galant, remote-head keys followed in 2006, and the blade changed from the straight MIT6 to the shouldered MIT3 during the 2007 model year. The 2007 Outlander and 2008 Lancer introduced FAST-key, Mitsubishi's keyless operation system, which carried on through the Lancer Evolution X and the Outlander Sport. Later Mirage, Eclipse Cross and Outlander Sport smart keys are newer designs that need their own tool coverage, and the Nissan-based 2022-on Outlander uses an AES-encrypted fob. The Dodge Dakota-based Raider pickup follows Chrysler's Sentry Key rules instead.

Most Mitsubishi transponder keys and FAST-key fobs are registered through the OBD-II port with a programmer that supplies the vehicle's security PIN, which professional tools can often retrieve and dealers release by VIN to verified owners. On many models the registration routine clears every stored key and relearns only the ones present, so bring all the keys you want to keep. Separate keyless remotes from the early 2000s can usually be paired on board with a jumper across pins 1 and 4 of the diagnostic connector, but remote-head keys and smart fobs from 2006 onward need a programmer. Used Mitsubishi remotes lock to the first car they learn, so a secondhand one has to be unlocked or renewed before it will pair, and some newer fobs can't be reused at all. The 2022-and-later Outlander and Outlander PHEV follow Nissan-style procedures that may need a gateway bypass or a dealer step. We check your ID and registration before any of this.

All Eclipse keys lost

If every key to your Mitsubishi is gone, the first job is a working blade. We decode the driver's door lock or cut from a key code the dealer releases by VIN with proof of ownership. Then the immobilizer PIN is obtained and new keys are registered at the car, at least two, which also drops the lost keys from memory. FAST-key and newer smart-key cars need a new fob plus its emergency insert, and remote-head keys need the blade cut and the buttons paired. Most turn-key and older FAST-key models are handled where they sit. Newer smart keys on some Mirage, Eclipse Cross and Outlander Sport builds, plus the 2022-and-later Outlander and Outlander PHEV, may need a dealer PIN or a dealer visit, and we tell you before you commit. Expect to show ID first.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Mitsubishi Eclipse requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Mitsubishi Eclipse, ask us directly and you'll get a plain answer.

How the job works

1. Identify the exact key your Eclipse uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Eclipse, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Eclipse key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Mitsubishi Eclipse is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Eclipse key types explained

• Transponder (chip) key. Transponder chips come in families, such as Texas Instruments 4C and 4D, Philips 46, Megamos 48 and the newer 128-bit AES types, and a Mitsubishi Eclipse only accepts the one its immobilizer was built around. That's why a hardware-store blank that looks right often won't start the car. We match the blank to the vehicle's chip and keyway before cutting. One more practical note: the chip lives in the plastic head, and when that head cracks, the chip can fall out or shift away from the antenna. If the car starts some days and not others, a damaged head is a frequent reason, and replacing the key before it quits entirely costs less than an all-keys-lost visit.
• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2012 Mitsubishi Eclipse with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Key with separate remote fob. Pairing a separate remote to a 2012 Mitsubishi Eclipse is a different job from programming the ignition key. Some vehicles accept new remotes through an on-board sequence of key turns and button presses; others need a scan tool connected to the OBD-II port. On many of them, entering remote programming mode clears every remote the car already knows, so any remote you want to keep has to be present and re-paired during the same session. Before we start, gather every remote that belongs to the vehicle. Leaving one in a kitchen drawer is a classic way to end up with a remote that quits the day after a new one is added.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.

Common Mitsubishi key problems

• Remote-head keys on the 2006-2007 Eclipse, Galant and Endeavor came with either a straight MIT6 blade or a shouldered MIT3 blade depending on build date. Check which one your old key has before ordering, because the two are not interchangeable.
• Mitsubishi remotes and smart fobs lock to the first vehicle they're programmed to. A used one from a salvage yard or online seller has to be unlocked or reflashed before it will pair, and some newer fobs cannot be reused at all.
• Remote-head keys and smart fobs take different coin cells: the remote-head keys use a thin CR1620, while FAST-key and smart fobs use a CR2032. A cell of the wrong thickness may not make good contact, so read the old battery before buying.
• Key registration on many Mitsubishis wipes every stored key and relearns only the ones present. A spare left at home during the appointment stops working afterward, so gather every key you want to keep before we start.
• The 2007 Outlander used a one-year FAST-key fob, FCC ID OUCG8D-640M-KEY-N, that differs from the OUC644M-KEY-N fob used from 2008 on. Ordering by model name alone often brings the wrong part.
• Mirage hatchbacks built before about March 2014 use the same FAST-key fob as the Outlander, while later Mirage fobs are a different design. The build date on the driver's door-jamb label settles which one you need.
• Inland Empire heat drains fob batteries faster than the calendar suggests. On FAST-key cars, a key warning on the dash or a fob that only works up close usually means a weak CR2032, an easy fix before it strands you.
• Eclipse and Galant models built in 2000 and early 2001 use a Texas 4D60 key, while later 2001 cars use 4D61. A key stamped R on the blade is the early type and one stamped N is the later type, and the wrong chip will turn the locks but not start the engine.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.