Genesis G90 Key Replacement

G90 keys by generation

The second-generation G90 uses a seven-button smart fob (FCC ID TQ8-FOB-4F53U) with lock, unlock, trunk, panic, remote start and forward and reverse Remote Smart Parking Assist buttons. It carries a Hitag 3 (ID47) chip and a CR2450 battery. The car also supports Genesis Digital Key on compatible phones. Its flush door handles hide a cover over the mechanical keyhole, which is revealed when the handle is pulled out, and a small emergency blade lives inside the fob. We confirm coverage for your VIN before the visit. When supported, new fobs register through the OBD-II port using the VIN-based PIN, with all keys present because the session may relearn the key list. All-keys-lost on this flagship can involve extra steps or a dealer-supplied fob, and Digital Key credentials are always managed through the owner's Genesis account rather than by a locksmith.

All first-generation G90s use a four-button smart fob (lock, unlock, trunk, panic) and push-button start. Suppliers list two fobs: base part 95440-D2000 (FCC ID SY5HIFGE04), shared with the 2017-2020 G80, and part 95440-G9000 (TQ8-FOB-4F16), listed for 2019-2020 cars. Both take a CR2032 cell and hide an emergency blade for the driver's door. Cars built after the 2020 refresh may differ again, so we match yours by part number before ordering anything. G90 fobs register through the OBD-II port with the VIN-based PIN, and every key you want to keep should be programmed in the same session. Spare keys are routine when a working fob is present. All-keys-lost is often possible too, but parts for this flagship are less common, so we confirm the fob and tool coverage by VIN first. Pressing the start button with the fob starts the car when the fob battery is dead.

Genesis key security

Genesis became a stand-alone luxury brand in the US with the 2017 model year, and every Genesis sold here starts with a push button and a smart proximity fob. There is no turn-key ignition anywhere in the lineup. The immobilizer and smart key system come from Hyundai Motor Group engineering, so the logic is familiar to anyone who programs late-model Hyundai and Kia vehicles: the car only starts when it reads a registered fob, and registering a fob generally requires a PIN tied to the VIN. The fob hardware has changed in steps. The first G80 and G90 used four-button fobs on CR2032 cells, and the early G70 followed with a similar four-button design. Six- and eight-button fobs with remote start, headlight and Remote Smart Parking Assist buttons arrived on the GV80, the redesigned G80 and the GV70, built around a Hitag 3 (ID47) transponder. The second-generation G90 and the GV60 use larger CR2450 cells. The refreshed GV80 and later G70 builds moved to five- and seven-button fobs with Hitag AES (4A) chips. Newer models also offer Genesis Digital Key, which turns a phone into a key, and the GV60 adds face recognition and a fingerprint reader. Those credentials live in the owner's Genesis account. A locksmith programs the physical fob; you or the dealer set up the phone side.

Genesis fobs are registered through the OBD-II port with a professional key programmer. The tool asks for the vehicle's immobilizer PIN, which registered locksmiths request by VIN through the NASTF Vehicle Security Professional registry or, on some models, obtain by other methods the tool supports. Without that PIN the car will not enter learn mode, so we confirm the VIN and your paperwork before ordering parts. Some Hyundai-group systems relearn the whole key list during registration, so bring every fob you own and expect them all to be programmed in the same session. A fob left out may stop starting the car afterward. That relearn is also the cleanest way to shut off a fob that was lost or stolen. Match a replacement by part number and FCC ID, not by looks. Two fobs for the same model year can differ in buttons, remote start, parking-assist functions and chip type. The hidden emergency blade is cut separately, by key code or by decoding the door lock.

All G90 keys lost

Losing every key to a Genesis is a bigger job than adding a spare, but it doesn't automatically mean a tow to the dealer. Because Genesis programming depends on the VIN-based PIN rather than on an existing working key, the all-keys-lost procedure on many models looks a lot like adding a key: we open the car, connect through the OBD-II port, enter the PIN and register new fobs, then cut the emergency blade from the key code. Coverage is less certain on the newest builds. Fobs with Hitag AES chips and recently refreshed models are where aftermarket tool support is most likely to lag, and phone keys always run through the Genesis account. We check coverage by VIN before driving out, verify your ID and registration on arrival, and tell you on the phone if your car needs the dealer instead.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Genesis G90 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Genesis G90, ask us directly and you'll get a plain answer.

How the job works

1. Identify the exact key your G90 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Genesis G90 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Genesis keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your G90, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a G90 key

• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

G90 key types explained

• Smart proximity key (push-to-start). A smart or proximity key lets a 2026 Genesis G90 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.
• Phone as key. Phone keys fail in ordinary ways: a dead battery, an app that logs you out after an update, Bluetooth switched off, or a new phone that hasn't been set up yet. That's why every vehicle with a phone key, including a Genesis G90, should have a working physical backup, whether that's a key card, a fob or a keypad code. Some phones keep a power reserve that lets the wallet key work for a while after the screen goes dark, but don't count on it in a parking garage. Where your platform allows a locksmith to program a backup fob or card, we can do that on-site; where it doesn't, we'll explain the dealer path.

Why a spare key pays for itself

• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.

Common Genesis key problems

• Weak fob batteries cause most Genesis key complaints. A key-not-detected message or shrinking remote range usually means the CR2032 or CR2450 cell is fading, and a car parked in inland summer heat drains it faster.
• Ordering a fob by model year alone often goes wrong. Genesis used several fobs per model with different buttons, chips and batteries, so the part number and FCC ID printed on your current fob are what count.
• Used or refurbished fobs bought online are a gamble. They can arrive locked to another vehicle, with the wrong part number or with a worn case, and a fob that can't be programmed to your car is money wasted.
• Owners often leave a spare at home. Some Hyundai-group systems relearn the whole key list during registration, so a fob that isn't in the car for the session may stop starting it afterward. Bring every fob you own.
• Plenty of drivers have never seen their emergency blade. It slides out of the fob, and on several models the driver's door keyhole hides under a cap or cover on the handle that has to come off first.
• Phone keys fail when the phone does. A dead phone battery, a signed-out Genesis account or a new handset can leave Digital Key users stuck, so keep a physical fob where you can reach it.
• On the GV60 and the Electrified models, a drained 12-volt battery can make the car ignore a perfectly good fob. We test that small battery before anyone spends money on a new key.
• Buttons that work only sometimes after a drop or a trip through the washing machine usually point to board damage inside the fob. A fresh coin cell won't fix that; a new programmed fob will.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.