2020 Ford Explorer Key Replacement

2020 Explorer key specs

The rear-drive-based 2020 Explorer moved to Ford's newer electrical architecture. Retail trucks start with a button and use slim Hitag Pro fobs: a four-button 315 MHz version (FCC ID M3N-A2C931423) and a five-button 902 MHz version with remote start (FCC ID M3N-A2C931426). From about 2022, a newer fob family, FCC ID M3N-A3C054339, appears in catalogs, and some 2024 trucks use the 434 MHz fob of the refreshed model. Ford's flip key is also listed for early trucks built with a turned ignition.

What's specific to the 2020 Explorer

2020 was the first model year of the Explorer Sixth generation, U625. Early-production cars sometimes use different part numbers than later ones, so for a 2020 Ford Explorer we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2019 Explorer used a flip key and a smart proximity key with push-button start, while the 2020 uses a smart proximity key with push-button start and a flip key. Keys from the older car will not work in this one.

A 2020 Ford Explorer is about 6 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2020 Ford Explorer

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2020 Ford Explorer is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.
• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Ford Explorer, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2020 Explorer and which we don't.

How the Ford immobilizer works on the Explorer

• These Explorers share their platform and much of their key hardware with the 2020-2024 Lincoln Aviator.
• Fobs from the 315 MHz, 902 MHz and newer M3N-A3C054339 families are separate parts and don't substitute for each other.

Programming a 2020 Explorer key

Fobs are added through the OBD-II port with a programmer that supports this architecture, and the emergency blade is cut on a laser-style machine. A spare is routine with a working fob present. All-keys-lost on these trucks commonly needs an alarm bypass cable, and some builds need an online security step, so we check your VIN against current coverage before quoting.

Nearly all Ford key programming runs through the OBD-II port. On turn-key Fords from roughly 2000 to 2014, our programmer requests PATS security access, often a timed wait of about ten minutes, and then adds a key or erases and rebuilds the key list. If you already have two working keys, many of these vehicles also accept Ford's owner procedure, where each good key is switched on in turn, followed by the newly cut key. A fixed-code 4C key can simply be cloned. Most separate remotes from that era pair when the ignition is cycled eight times in quick succession, while integrated remote-head keys usually learn their buttons along with the chip. Hitag Pro flip keys and every push-button fob are registered with a programmer. On many 2015-and-later models an active alarm means an emulator or bypass cable for all-keys-lost work, and some 2020-and-later models add an online authorization step. We check your ID and registration or title before we start.

Spares are routine; all-keys-lost often needs a bypass cable or an online step, confirmed by VIN first.

Lost every key to your Explorer?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Ford Explorer can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ford Explorer requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Ford Explorer, ask us directly and you'll get a plain answer.

Explorer key battery

Battery details for the 2020 Explorer: CR2450 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Explorer uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ford Explorer keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ford keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Explorer, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Explorer key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Explorer came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2020 Ford Explorer key?

Locked out, keyless, or just tired of a fob that only works half the time? Julian's Locksmith can help with your Explorer in Southern California. Have your registration and photo ID ready, call (951) 903-3193, and we'll give you an honest answer about what we can do on-site and what it will cost before we head your way.