2013 Ford Explorer Key Replacement

2013 Explorer key specs

The 2011 Explorer became a unibody crossover, and its keys split by trim. Base and XLT models usually start with an 80-bit remote-head key, FCC ID CWTWB1U793, in three- and four-button versions, including remote-start keys. Limited models, and later the Explorer Sport, have Intelligent Access with push-button start and a 315 MHz smart fob, FCC ID M3N5WY8609, with an 8-cut emergency blade. A truck built with one system won't accept keys from the other.

What's specific to the 2013 Explorer

The 2013 Ford Explorer is the third of 5 model years in the Explorer Fifth generation, U502 (2011–2015), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 13 years old, a 2013 Ford Explorer has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2013 Ford Explorer

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2013 Explorer, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2013 Ford Explorer is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.
• Transponder (chip) key. A transponder key carries a small chip in its head, usually a glass capsule or a carbon wafer, with no battery of its own. When you turn the key in a 2013 Ford Explorer that uses one, an antenna ring around the ignition energizes the chip and asks for its code. If the answer matches what the immobilizer has stored, the engine is allowed to run. If it doesn't, you get the classic symptoms: the engine cranks but won't fire, or it fires and dies after a second, and the security light on the dash flashes or stays lit. That's why a perfectly cut copy without a programmed chip will open the doors but won't start the car.

How the Ford immobilizer works on the Explorer

Ford's immobilizer is PATS, the Passive Anti-Theft System, sold under the SecuriLock name. A transponder sealed in the key head, or built into the fob on push-button models, answers a coded challenge from a coil around the ignition or from antennas in the cabin, and the engine won't run until the powertrain computer accepts the answer. Across 2000-2026 the chip changed in clear steps. Pickups, big SUVs and the Crown Victoria used a fixed-code Texas 4C chip into the early 2000s, and the Excursion kept it through 2005. The first Escape and early Focus used a Texas 4D60. Between 2000 and 2004 most of the lineup moved to the encrypted Texas 4D63, with 80-bit versions becoming the norm around 2011, while most catalogs list the E-Series van with chip keys only from 2008. NXP Hitag Pro arrived with the 2013 Fusion, reached the F-150 for 2015 and now covers nearly the whole lineup. Remote-head keys appeared in the mid-2000s, Intelligent Access push-button fobs around 2010, and long-range 902 MHz fobs came with remote start. Recent models use 434 MHz fobs, and the Mustang Mach-E and F-150 Lightning added Phone As A Key.

• The smart fob, M3N5WY8609, is shared with the 2011-2014 Edge and the 2013-2019 Flex and Taurus.
• The three-button remote-head key, Ford 164-R8070, is also listed for the 2011-2014 F-150 and 2011-2016 Super Duty.

Programming a 2013 Explorer key

Remote-head keys are programmed at the OBD-II port after the timed security access, and their buttons learn along with the chip; Ford's two-key owner routine also works. Smart fobs are registered with a programmer, and the emergency blade is cut to the door lock. All-keys-lost is a single visit for either system: we decode the lock, cut a blade, erase the missing keys and program two.

Lost every key to your Explorer?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Ford Explorer can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ford Explorer requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Ford Explorer, ask us directly and you'll get a plain answer.

Explorer key battery

Most fobs for a 2013 Ford Explorer open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your Explorer uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ford keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ford system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of an Explorer key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your Explorer came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ford key problems

• On high-mileage trucks and SUVs from the 2000s, a key that sticks or won't turn usually points to worn ignition wafers or a key copied from a copy. A key cut fresh to factory code often turns smoothly again, and badly worn cylinders can be rebuilt.
• Many Fords carry a SecuriCode keypad on the driver's door or pillar. The five-digit factory code is printed on a wallet card in the owner's packet, and if that card is lost, the code can usually be read with a scan tool.
• MyKey, which spread across the lineup from about 2010, lets an admin key limit top speed and audio volume on another key. A newly programmed key carries no restrictions until you set MyKey up again in the vehicle menu.

Tips from a mobile locksmith

• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2013 Ford Explorer key?

Need a key for your 2013 Ford Explorer? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.