2018 Ford Explorer Key Replacement

2018 Explorer key specs

The 2016 refresh moved the Explorer to Hitag Pro keys and the side-milled HU101 blade. Base trucks start with a turned key and a three-button flip key (Ford 164-R8130, FCC ID N5F-A08TAA). Most others use Intelligent Access fobs: for 2016-2017, a four-button fob in 315 MHz form (FCC ID M3N-A2C31243800) or 902 MHz remote-start form (FCC ID M3N-A2C31243300); for 2018-2019, Ford's slimmer fob, FCC ID M3N-A2C93142300, or its 902 MHz counterpart, M3N-A2C931426.

What's specific to the 2018 Explorer

The 2018 Ford Explorer is the third of 4 model years in the Explorer Fifth generation refresh (2016–2019), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At roughly 8 years old, a 2018 Ford Explorer has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2018 Explorer can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2018 Ford Explorer

• Flip (switchblade) key. A flip key folds its blade into the fob on a spring-loaded hinge and swings it out with the press of a button. Inside the body sit the transponder chip and the remote circuit board, which means the metal blade itself carries no electronics. That's good news when the blade snaps. On many flip keys for a Ford Explorer, we can cut a new blade to your key code and fit it into your existing fob, with no reprogramming required, because the chip and remote never left the housing. Many flip-key blades are laser-cut, with a groove milled along the side rather than notches on the edge, so they need a code machine built for that profile.
• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2018 Ford Explorer is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Ford immobilizer works on the Explorer

• The 2016-2017 fobs take a CR2032, while the slimmer 2018-2019 fobs take a CR2450.
• Catalogs list the three-button flip key, Ford 164-R8130, for Explorers from 2016 through 2022, so one key style covers the base trim of two generations.

Programming a 2018 Explorer key

Flip keys and fobs are programmed through the OBD-II port with a programmer that covers Ford's Hitag Pro system, after a timed security access. We cut the HU101 blade or emergency insert on a laser-style machine. Spares are routine from one working key. With every key lost, an active alarm can call for an emulator or bypass cable, so we confirm coverage by VIN before quoting.

Spare keys are routine; all-keys-lost on these Hitag Pro Explorers can need an emulator or bypass cable, which we confirm by VIN first.

Lost every key to your Explorer?

When every key to a Ford is gone, older models are usually a single visit. We cut a working key from the factory key code or by decoding a door lock, then erase the missing keys from PATS and program new ones, so a lost key that turns up later won't start the vehicle. Ford's procedure expects at least two keys after an erase, so plan on two. Push-button Fords get new fobs plus freshly cut emergency blades through the same port. On push-button Fords from about 2015 on, an active alarm often means an emulator or bypass cable, and on many 2020-and-later models, including the current F-150, Super Duty, Bronco and Explorer, all-keys-lost can also call for an online security step or, on some builds, the dealer. We check your VIN against current tool coverage before quoting, and we ask for ID and proof of ownership first.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2018 Ford Explorer we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

Explorer key battery

Battery details for the 2018 Explorer: CR2032 (flip key and 2016-2017 fob); CR2450 (2018-2019 fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Explorer uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ford system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of an Explorer key

• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ford system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ford key problems

• With only one programmed key, Ford's do-it-yourself spare routine is off the table because it needs two working keys. Adding a second key while the first still works is far simpler than an all-keys-lost visit later.
• On high-mileage trucks and SUVs from the 2000s, a key that sticks or won't turn usually points to worn ignition wafers or a key copied from a copy. A key cut fresh to factory code often turns smoothly again, and badly worn cylinders can be rebuilt.
• Battery sizes changed over the years. Separate remotes, remote-head keys and flip keys mostly take a CR2032, while most Ford smart fobs from about 2017 on take a thicker CR2450. Inland Empire heat shortens either one, so read the old cell before buying.
• Many Fords carry a SecuriCode keypad on the driver's door or pillar. The five-digit factory code is printed on a wallet card in the owner's packet, and if that card is lost, the code can usually be read with a scan tool.

Tips from a mobile locksmith

• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2018 Ford Explorer key?

Don't wait until the last key disappears. If your Ford Explorer is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.