2019 Chrysler 300 Key Replacement

2019 300 key specs

For 2019 the 300 kept the same fob shape but moved to a Hitag AES transponder and a new FCC ID, M3M-40821302, so a 2018 fob will not program to a 2019 car even though the two look alike. Buttons are lock, unlock, trunk and panic, with remote start on equipped cars, and the emergency blade slides out of the case. The final 2023 model year included a 300C with the 6.4-liter V8, and its key follows the same pattern.

What's specific to the 2019 300

2019 was the first model year of the 300 LD (2nd generation, AES smart key). Early-production cars sometimes use different part numbers than later ones, so for a 2019 Chrysler 300 we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. The key looks similar to the 2018 model's, but the chip moved from Philips ID46 (Hitag2) to Hitag AES (ID 4A), so an older key is not a substitute.

A 2019 Chrysler 300 is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Chrysler 300

• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Chrysler 300 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Chrysler immobilizer works on the 300

Chrysler began fitting its Sentry Key Immobilizer System (SKIS) in the late 1990s, and by the 2001 model year most Chryslers in our range used it. The first wave of keys carried a Texas Instruments 4D64 chip in a head cut for the Y159-family keyway, sold as the Ilco Y160-PT blank. From about 2004 the chip changed to a Philips ID46, and most cars paired it with a remote-head key that put the transponder and the keyless entry buttons in one piece. For 2008 the 300 and Town & Country moved to the fobik, a blade-less remote that turns inside a wireless ignition node (WIN), with a proximity version for push-button start. The 2011 redesign of the 300 added a proximity smart key, and the Pacifica minivan, the 2015–2017 200 and the 2019–2023 300 use fobs with Hitag AES encryption. Vehicles from 2018 on also carry a secure gateway module that limits what aftermarket tools can write. Two models break the pattern: the Mitsubishi-built Sebring coupe uses a 4D61 chip and a Mitsubishi blade, and the Mercedes-based Crossfire uses an HU64 flip key with Mercedes immobilizer electronics.

• Supplier listings show the 2019–2023 300 fob with an NXP Hitag AES 128-bit chip, the same family used in the 2017-and-later Pacifica.
• The 2023 model year was the last for the Chrysler 300.
• The secure gateway module that arrived for 2018 still applies, so tool access is part of every key job on these cars.

Programming a 2019 300 key

These cars combine the AES fob with the secure gateway module, so programming needs a current tool, a gateway bypass or authenticated connection, and the vehicle PIN. Adding a spare to a car with a working fob is usually straightforward. With every fob lost, some cars can be done over OBD-II and others need the radio frequency hub handled on the bench or a dealer visit, so we confirm by VIN first.

Spare fobs are routine; all-keys-lost on these AES cars sometimes needs module work or a dealer visit.

Lost every key to your 300?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Chrysler 300 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Chrysler 300 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Chrysler 300, ask us directly and you'll get a plain answer.

300 key battery

Most fobs for a 2019 Chrysler 300 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 300 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chrysler keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 300, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 300 key

• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chrysler key problems

• On 2008–2016 Town & Country vans and 2008–2010 300s, a fobik that will not turn or is not recognized may be a worn fob or a failing wireless ignition node. We test with a known-good fob before anyone replaces parts.
• Remote-head keys from the 2004–2014 era often crack where the blade meets the plastic head. A new shell can save the electronics, but the transponder chip has to move with them or the car will not stay running.
• Sebring orders get mixed up often: the sedan and convertible use Chrysler keys and fobs, while the 2001–2005 Sebring coupe uses Mitsubishi-based keys and remotes that fit none of the other Sebrings.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2019 Chrysler 300 key?

Don't wait until the last key disappears. If your Chrysler 300 is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.