2010 Chrysler 300 Key Replacement

2010 300 key specs

For 2008 the 300 switched to Chrysler's fobik: a blade-less remote that you push into a dash-mounted wireless ignition node and twist. The fob holds lock, unlock, trunk and panic buttons, a remote-start button on equipped cars, and a small emergency key for the door. Some cars were built with Keyless Enter 'n Go, which uses a proximity version of the same fob. Replacements are listed under FCC ID IYZ-C01C (also printed as M3N5WY783X) at 433 MHz, with a Philips ID46 chip in both versions.

What's specific to the 2010 300

2010 was the final model year of the 300 LX (1st generation, fobik), before the LD (2nd generation, ID46 smart key) arrived for 2011. Late-run cars occasionally pick up running changes, so we check the VIN instead of assuming a 2010 Chrysler 300 matches a 2008.

A 2010 Chrysler 300 is about 16 years old. Original keys are often worn smooth, and some factory remotes for cars this age are discontinued, so we may suggest a quality aftermarket remote or a separate fob. Because older immobilizers are simpler, all-keys-lost jobs on cars this age are usually more straightforward than on late models.

Key options for the 2010 Chrysler 300

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2010 300, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Chrysler 300 LX (1st generation, fobik), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Chrysler immobilizer works on the 300

Chrysler began fitting its Sentry Key Immobilizer System (SKIS) in the late 1990s, and by the 2001 model year most Chryslers in our range used it. The first wave of keys carried a Texas Instruments 4D64 chip in a head cut for the Y159-family keyway, sold as the Ilco Y160-PT blank. From about 2004 the chip changed to a Philips ID46, and most cars paired it with a remote-head key that put the transponder and the keyless entry buttons in one piece. For 2008 the 300 and Town & Country moved to the fobik, a blade-less remote that turns inside a wireless ignition node (WIN), with a proximity version for push-button start. The 2011 redesign of the 300 added a proximity smart key, and the Pacifica minivan, the 2015–2017 200 and the 2019–2023 300 use fobs with Hitag AES encryption. Vehicles from 2018 on also carry a secure gateway module that limits what aftermarket tools can write. Two models break the pattern: the Mitsubishi-built Sebring coupe uses a 4D61 chip and a Mitsubishi blade, and the Mercedes-based Crossfire uses an HU64 flip key with Mercedes immobilizer electronics.

• A fobik from a 2008–2010 300 is also listed for the Dodge Charger and Challenger of those years, but each fob must be programmed to its own car.
• A worn or cracked fobik can stop the ignition node from reading it even when its lock and unlock buttons still work.
• On fobik cars the fob itself turns the ignition, so there is no ignition key code to cut, only the small emergency insert for the door.

Programming a 2010 300 key

The wireless ignition node (WIN) holds the immobilizer, and new fobiks are added through the OBD-II port using the 4-digit PIN. Cars built before 2011 can sometimes learn an extra fobik on board when two working fobs already start the engine. A fobik is never cut, so all-keys-lost on these cars is mostly an electronic job: we obtain the PIN, program new fobiks, and cut the small emergency insert for the door.

Lost every key to your 300?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Chrysler 300 can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare stored safely at home rescues you from a locked car with the fob sitting on the seat, a key dropped somewhere along a hiking trail, or a fob that stops responding on a busy morning. Keep it indoors, never in a magnetic box under the bumper.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your 300 and your schedule.

300 key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your 300 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 300, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 300 key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your 300 came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Chrysler system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chrysler key problems

• The 2018 and 2019 Chrysler 300 smart keys look identical but carry different transponder chips and different FCC IDs, M3N-40821302 versus M3M-40821302. Ordering by appearance alone leads to a fob that will not program, so match the model year and part number.
• Sebring orders get mixed up often: the sedan and convertible use Chrysler keys and fobs, while the 2001–2005 Sebring coupe uses Mitsubishi-based keys and remotes that fit none of the other Sebrings.
• On 2008–2016 Town & Country vans and 2008–2010 300s, a fobik that will not turn or is not recognized may be a worn fob or a failing wireless ignition node. We test with a known-good fob before anyone replaces parts.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2010 Chrysler 300 key?

The quickest route to a working key for a 2010 Chrysler 300 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.