2012 Chrysler 300 Key Replacement

2012 300 key specs

The redesigned 300 went to proximity entry and push-button start, and most supplier listings show smart keys for these years. The fob has four buttons (lock, unlock, trunk, panic), or five with remote start, and a release on the side frees an emergency blade for the driver's door. Through 2018 it is listed under FCC ID M3N-40821302 with a Philips ID46 (Hitag2) chip, the same unit used on the Dodge Charger of those years. A few catalogs also list the older fobik-style proximity fob, IYZ-C01C, for some 2011–2015 cars, so match the FCC ID on your original.

What's specific to the 2012 300

The 2012 Chrysler 300 is the second of 8 model years in the 300 LD (2nd generation, ID46 smart key) (2011–2018), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 14 years old, a 2012 Chrysler 300 has usually seen real wear. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2012 Chrysler 300

• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2012 Chrysler 300 is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Chrysler immobilizer works on the 300

• From 2018 the 300 has a secure gateway module, and aftermarket programmers need a bypass cable or authenticated login to finish key work.
• The 2015 refresh changed styling and the interior but kept the M3N-40821302 ID46 smart key through 2018.
• Supplier fitment lists the same fob for the 2011–2018 Charger and 2015–2018 Challenger, but each fob must be programmed to its own car.

Programming a 2012 300 key

New smart keys are programmed through the OBD-II port with a tool that obtains the 4-digit PIN and writes the fob to the car's radio frequency hub. Adding a key and all-keys-lost follow nearly the same path, since no blade has to start the engine. On 2018 cars the factory secure gateway module blocks many aftermarket tools from writing data, so a bypass cable or authenticated access becomes part of the job.

Lost every key to your 300?

Losing every key is usually recoverable on a Chrysler without towing it to a dealer. For bladed keys, we decode a door lock or cut by code from the VIN record after confirming you own the vehicle, then program a new transponder or remote-head key through the OBD-II port. Fobik-equipped vans and sedans need no ignition cut, so that work is mostly electronic plus a new emergency insert for the door. The harder cases are the AES-encrypted smart keys on the Pacifica, Voyager, 2015–2017 200 and 2019–2023 300, where some vehicles need the radio frequency hub handled directly or a dealer visit, and the Crossfire, whose Mercedes-derived keys are normally ordered pre-coded. We tell you which case applies before we drive out.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Chrysler 300 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Chrysler 300, ask us directly and you'll get a plain answer.

300 key battery

Most fobs for a 2012 Chrysler 300 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2032, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 300 uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Chrysler 300 keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Chrysler keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your 300, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a 300 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Chrysler 300 is the most involved of all, both in the part itself and in the programming.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Chrysler system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Chrysler key problems

• Remote-head keys from the 2004–2014 era often crack where the blade meets the plastic head. A new shell can save the electronics, but the transponder chip has to move with them or the car will not stay running.
• The 2018 and 2019 Chrysler 300 smart keys look identical but carry different transponder chips and different FCC IDs, M3N-40821302 versus M3M-40821302. Ordering by appearance alone leads to a fob that will not program, so match the model year and part number.
• Remotes bought online for 2004 and later Chryslers still have to be paired to the car. Some cars through about 2010 can learn one at home if you hold two working keys; otherwise it takes a programming tool, and used fobs must be unlocked first.
• On 2008–2016 Town & Country vans and 2008–2010 300s, a fobik that will not turn or is not recognized may be a worn fob or a failing wireless ignition node. We test with a known-good fob before anyone replaces parts.

Tips from a mobile locksmith

• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2012 Chrysler 300 key?

The quickest route to a working key for a 2012 Chrysler 300 starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.