Magnetic Lock Installation in Rubidoux: Glass, Double and Office Doors

Magnetic Lock Installation in Rubidoux: what to expect

Because a maglock has no latch, nobody leaving a building can operate a handle to get out; the lock has to let go for them. That is why magnetic lock installation on exit doors follows a pattern. A sensor above the door detects someone approaching from the exit side and cuts power. A push button near the door, wired to interrupt power directly instead of relying on a software setting, gives a second way out. The fire alarm system, and where required the sprinkler system, also cuts power so the door opens in an emergency, and losing power releases the lock by itself. Those requirements come from the building code California adopts, with local amendments, and the building department or fire marshal decides how they apply to your door. Delayed-egress locks, used in some care and retail settings, follow separate rules. We design to your jurisdiction's expectations and note which parts need review, so you aren't guessing when someone with a clipboard visits.

Work included on a typical visit

• Header-mounted maglocks on outswing doors. On an outswing door with a sound header, the magnet mounts on the frame above the door and the armature plate mounts on the door face directly beneath. This is the cleanest magnetic lock installation: a straight bolt-up, short wiring and good alignment. We check the header for strength and anchor into solid material, not drywall.
• Inswing doors, brackets and offset mounts. Bracket choice is where installs go wrong. Inswing doors, deep headers and thick doors all change the geometry, and a cheap bracket that flexes gives up holding force. We use rigid kits, check them against the actual door, and avoid stacking parts that introduce play.
• Exit sensors and push buttons. A motion sensor above the door detects someone leaving and cuts power so the door opens. A push button, mounted near the door and wired to interrupt power directly, gives a second route out. We aim the sensor at the exit side and test it with people walking, carrying items and moving slowly.
• Readers, keypads and controllers. A reader or keypad tells the controller to release the lock for a few seconds. We connect the reader, controller and lock, set the release time, and configure schedules and credentials. Cards or codes can be canceled instantly, which is far easier than rekeying a door.
• Door position switches, bond sensors and monitoring. Propped doors defeat access control. A door-position switch with a timer can chirp or notify when a door has been left open too long, and a bond sensor flags a magnet that isn't holding. Both are inexpensive additions at installation time and tedious to add later.

What's different about Rubidoux

Shopping-center tenants use maglocks mostly on stockroom, back-of-house and office doors, and sometimes on glass entry doors after hours. The storefront frame belongs to the landlord, and exit rules apply to the rear corridor too. In Rubidoux centers we check delivery routes, fire alarm tie-ins and the way back doors are really used, because a maglock that traps an employee carrying inventory is a problem waiting to happen.

Warehouse and industrial doors are heavy, often outswing steel on thin frames, and exposed to forklifts, dust and temperature swings. A maglock needs solid anchoring and a plate that stays aligned despite vibration. Many pedestrian doors on industrial sites in Riverside County fall under stricter life-safety rules because workers need dependable exits, so we check that early and may recommend a different lock.

School offices, childcare centers, churches and youth-sports buildings in Rubidoux often use maglocks on glass entry doors so staff can control who comes in. Children and visitors must always be able to leave, which makes the sensor, button and fire alarm release central. We design for substitute staff and volunteers, label the exit button plainly, and keep the system simple enough for anyone to understand.

Situations this covers

• For example, a fitness studio has double glass doors off a shared hallway near Jensen-Alvarado Historic Ranch and Museum. Members badge in, and the owner wants evening entry without handing out keys. We'd fit a magnet on each leaf, wire both to a card reader and controller, add sensors and a push button inside, and connect a fire alarm relay with the landlord's alarm contractor.
• A typical call: a small company keeps its network equipment in a closet with a hollow-metal door and a keyed knob that everyone has copied. The manager wants a keypad. We'd mount an inswing bracket kit, run cable above the ceiling, set a short release time, and discuss whether a strike on the existing latch might be a better fit.
• Picture a records room in a clinic. Only certain staff should enter, and the door is rarely used but must be monitored. We'd install a maglock with a bond sensor and a door-position switch, a reader outside and an exit sensor inside, plus an entry log, so the office manager can tell when the door was opened and whether it was left unsecured.
• Say an earlier installer put a maglock on an office door with a card reader and nothing else. There is no exit button, no sensor and no link to the fire alarm. We'd survey the door, explain what is missing, add a sensor, a push button and a release relay, and tell you honestly which parts the building official will care about.

From your call to the finished job

1. Survey the door, header and exit path. Before choosing a magnet, we check what you're attaching it to. A header that flexes, a door that sags or a closer that slams will undermine any lock. We note the problems and, if necessary, fix them before the lock goes in.
2. Design the release path and quote. A good design starts with the exit. We list every way the door releases, then add the credential that lets people in. You see the quote door by door, with notes on what could change. Nothing is drilled until you have approved it.
3. Mount the magnet and armature plate. We mark the layout, drill and anchor the bracket or backing plate into solid material, and mount the magnet square to the door. The plate goes on the door with through-bolts and a flexible bushing so it can seat flat against the magnet face, and we tighten everything to specification.
4. Run the power, sensors and fire alarm release. The push button interrupts lock power directly, the sensor does the same through its relay, and the fire alarm relay does it for the building. We test each one independently by operating it with the others disconnected.
5. Program credentials and set the timers. We set the door-held-open alarm, the lock's release delay and the sensor's hold time so they work together. Then we check that a credential, a button press and a sensor trigger each behave properly when tried separately and in sequence.
6. Test every release and hand over. Testing covers power on, power off, credential, push button, motion sensor and fire alarm release, with the door pulled hard against the magnet. We also test the batteries, if installed, and show you how to check the system monthly.

How we quote the job

• Door type and mounting hardware. A steel outswing door with a solid header is the simplest mounting. Glass doors need clamp brackets, inswing doors need offset kits, and aluminum storefronts may need backing plates or a concealed shear lock. Mounting hardware is often the biggest single part of the price, so we choose it first.
• Exit devices and fire alarm interface. Fire alarm interface varies. Some buildings have a simple relay available; others require the alarm contractor to do the work or sign off. We tell you which situation you are in during the survey, so the schedule and budget account for it.
• Permits, inspections and timing. Multiple doors, rated corridors and tenant improvement projects involve more coordination. We flag early which parts need a licensed electrician or fire alarm contractor, so your budget reflects the whole job and not only ours. When several trades touch one door, someone should own the schedule, and we are glad to coordinate.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Rubidoux.

What to do before we arrive

• Review who holds access a few times a year. Cards and codes pile up as staff, vendors and contractors come and go, and every extra credential is a door that opens for someone. Remove what you no longer need and keep a short list of current holders.
• If you rent, ask the landlord in writing before anyone drills the frame. A maglock may need removal when you leave, so keep a copy of the wiring diagram, the model information and any hardware that was taken out. The next tenant, and your landlord, will thank you.
• Put the push button where someone leaving would reach for it, with a clear label. Hide it behind a plant or a counter and it stops being an exit. Staff and visitors should be able to see it without being told.
• Stand at the door and ask yourself: if the lights went out and I had never been here, could I leave? If the answer needs a sign, a hidden button or a staff member's help, the design isn't finished. Say so when you call us in Rubidoux; we start with the exit.

What not to do

• Wiring the exit button through the controller only. If the controller hangs or loses power to its logic, the button does nothing. The push button should interrupt lock power directly, so the door opens even if the access system is dead.
• Drilling tempered glass. Once glass is tempered it can't be drilled or cut, and any attempt can shatter the panel. Use glass-door clamps that grip the edge. If a door was drilled previously, we can judge whether existing holes can be used safely.
• Skipping the alignment check. A plate that sits at an angle, or a gap wider than a business card, delivers only a fraction of the rated holding force. Tighten the plate with the door closed, then confirm the faces meet fully.

Reaching Rubidoux

Rubidoux is about 22 miles from our San Bernardino base, roughly 28 minutes in light traffic via Palm Avenue or University Parkway to I-215 South through San Bernardino, Colton and Grand Terrace. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

If you're close to Pacific Avenue, tell us which exit or cross street you're nearest. It trims the last mile and keeps the van from circling a block that looks right on the map but isn't.

About Rubidoux: The former Rubidoux census area covered about 9.9 square miles at an elevation of roughly 774 feet.

Business lock or door work in Rubidoux?

Call (951) 903-3193 with the address, the doors or hardware involved and when the site is open. We'll quote the job before any work starts and book a time within our hours that suits your schedule.