March Air Reserve Base Lock Rekey: New Keys Pinned Into Your Existing Cylinders

How this works in March Air Reserve Base

Rekeying is the right call far more often than people expect, but it isn't universal. Standard pin-tumbler hardware from Kwikset, Schlage, Weiser, Yale, Baldwin, Sargent and Corbin Russwin re-pins easily. Kwikset SmartKey cylinders use a sidebar and sliders instead of loose pins, so they reset with a tool and a working key rather than a pin kit. Interchangeable cores are swapped with a control key after we pin a new core. High-security cylinders with patented keyways, like Medeco, Mul-T-Lock or ASSA, can be rekeyed, but key blanks and some parts are controlled by authorized dealers, so registration paperwork matters. Then there are locks that shouldn't be rekeyed at all. A cylinder with wallowed-out pin chambers, broken springs or a cracked cam won't hold new pinning reliably. Some inexpensive imported keypad locks use proprietary cylinders with no pin kits available. A lock that was forced during a break-in usually needs replacement, not new pins. When someone in March Air Reserve Base calls, we ask about brand, age and symptoms so we arrive prepared, and we tell you at the door if a cylinder isn't worth the labor.

Work included on a typical visit

• Master pin removal or rebuilding. When a property changes management or an old master key goes missing, we remove master pins so each cylinder answers only to its own change key, or we re-pin the whole system to a new master. Fewer shear points also means a tighter cylinder that's harder to pick or bump open.
• Interchangeable core swaps. Small format and large format interchangeable cores come out with a control key, which makes rekeying quick: we pin a new core on the bench, pull the old one and slide the new one in. If the control key is lost, the job takes longer because the existing core has to be picked or drilled out first.
• Keying locks to a key you already carry. Have a key you like? If the keyway matches, we can pin your other cylinders to it so one key runs the house. We decode that key first, and if its cuts are worn we correct them to factory depth, so future copies work in every lock rather than just the one you started with.
• Padlocks, cam locks and gate cylinders. Many laminated and solid-body padlocks, file cabinet cam locks and keyed gate hardware can be re-pinned to match your door key or a separate utility key. Cheap wafer cam locks often cost less to replace than to rekey, and we'll tell you honestly which route makes sense for each one.
• Rekeying locks with no working key. Some cylinders resist the usual no-key methods. A SmartKey without a working key has to be disassembled or replaced, since the reset tool needs a key that already turns. Many high-security cylinders have a registered key number on file with the dealer, so the owner can order a working key by card instead of anyone attacking the lock.

Local factors in March Air Reserve Base

If you leave before sunrise and get home after dark, scheduling matters as much as the lock work. We start at 6:30 a.m. every day and work into the evening, so a lock rekey can happen before your commute or after it. If you can't be there, an adult you authorize can meet us with documentation, and the new keys go only to that person.

Newer tract homes frequently come with Kwikset SmartKey hardware, and before you got the keys they passed through builders, subcontractors, cleaners and the sales office. Resetting every cylinder to a key only you control is the first job after closing. We complete SmartKey resets with your working key, check the garage-entry and side doors that buyers tend to overlook, and explain your options if a few doors came with a different brand.

In a family home, keys spread quickly: grandparents, babysitters, neighbors, the house cleaner, a teenager who lost one at practice. Rekeying resets that list to whoever you choose. We key the front, garage-entry and back doors alike when the keyways match, and we can rekey the backup cylinder on a keypad deadbolt to the same key so the kids have one less thing to keep track of.

Situations this covers

A homeowner in Mission Grove buys a house from a neighbor and receives a bag of seven keys, none labeled. We'd rekey the front deadbolt, kitchen entry and back door to one new key, working in the driveway with a plug follower and a tray of pins. Each key gets tested in each lock. One deadbolt's cylinder turns out to be worn enough that the new key sticks slightly, so we'd offer a quick cylinder swap.

• Picture a small private school whose doors run on small format interchangeable cores, and the facilities lead retires without handing over the control key. Without it, no core can be swapped. We pick one core to the control line, decode the control bitting from its pins and cut a new control key. The school then decides whether to re-core every door to a fresh control system.
• Here's a familiar one: a homeowner rekeys a Kwikset deadbolt with a store kit, and the new key won't turn. On the bench, every pin turns out to be the right size but loaded in reverse, counted from the tip instead of the bow. We reorder the stack, check each chamber for nicks from the tweezers, then key the matching knob so both locks run on the same key.
• Suppose a daughter is handling her late father's house near March Field Air Museum as executor, and nobody can find keys to the back door or the detached workshop. She brings her ID and the letters testamentary from probate. We shim the back-door deadbolt plug, pick the workshop lock, and re-pin both to the front-door key she already carries, so the family ends up with a single key and a known count.

How the visit works

1. Count cylinders and confirm authorization. A good rekey starts with an inventory. We walk the property with you, note every keyed lock, including garage-entry, side gate and padlocks, and check identification or ownership documents before a single cylinder comes off a door in March Air Reserve Base.
2. Choose the new bitting. We either generate a new bitting code within the manufacturer's depth and adjacent-cut limits or decode a key you want to keep. The code is written down so replacement keys can be cut accurately later, even without an original key in hand.
3. Remove each cylinder. We work one door at a time, so a home or shop is never left with holes in several doors at once. Screws, retainers and cams go into a labeled tray for that opening, and the tailpiece orientation is noted before anything slides out, which removes guesswork at reassembly.
4. Re-pin at the shear line. This is the heart of a lock rekey. Each pin stack gets a new bottom pin matched to the new cut depth, and master pins are added or removed as the chart calls for. We inspect chambers and springs while the plug is out and replace anything worn.
5. Reassemble and test on the door. Our test is a checklist, not a quick turn. Every new key goes in and out of each cylinder, the bolt is thrown from outside and from the thumbturn, the key has to return to rest and pull out cleanly after locking and unlocking, and an old key gets a fair try.
6. Cut keys and leave a record. Before we leave March Air Reserve Base, every key is tried in every lock it should operate. Commercial keys can be stamped with identifiers, and you receive a record of what was cut and issued, so your key control starts from an accurate count.

How we quote the job

• How many cylinders. Most of the labor is per cylinder, so a condo with two keyed locks and a house with seven are different jobs. A front entry set usually counts as two cylinders, the knob or lever plus the deadbolt, and garage-entry, side and back doors each add more.
• Brand and cylinder type. Standard Kwikset and Schlage cylinders are the quickest to re-pin. SmartKey resets are fast with a working key and slower without one. Mortise, rim and interchangeable-core cylinders take more handling, and high-security brands add controlled blanks and parts to the job.
• Master keying and keying charts. A single-key rekey is straightforward. Adding or rebuilding a master key system means calculating master pins for every cylinder, cutting several key levels and documenting the chart, which takes more time and more parts than a simple re-pin of the same doors.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in March Air Reserve Base.

Mistakes to avoid

• Forgetting the digital side. Rekeying the override cylinder on a keypad or smart lock stops old keys, but an ex-roommate's PIN, a past guest code or a shared app login still opens the door. Delete old users and change the master code on the same day the cylinder gets re-pinned.
• Pulling the plug without a follower. The moment the plug leaves the housing, the springs shove drivers into the empty space, and the cylinder has to be reloaded pin by pin with tweezers, often after a spring or two has already vanished under the fridge.
• Buying a rekey kit for the wrong brand. Kwikset and Schlage pins are not interchangeable, and many kits include parts for only one keyway. Owners end up with mismatched stacks, a plug that won't turn and springs scattered across the kitchen table.

Advice before you book

• Test the deadbolt with the door shut, not only with it open. A cylinder can work perfectly on the bench while the bolt drags on the strike once the door is closed. If you have to push or pull the door to lock it, the strike likely needs adjusting.
• Use a dry lubricant. Graphite or a dry PTFE spray keeps pins moving freely. Wet oils attract dust and pollen, then thicken in warm weather and gum up the chambers, which is a common reason keys start sticking a year after a rekey.
• Write down how many keys exist after a rekey and who holds each one. Knowing the count is the whole point of rekeying. For a business in March Air Reserve Base, a simple sign-out sheet keeps that number accurate through staff changes and promotions.
• If your keys were stolen with something showing your address, such as a wallet with a license or a car with the registration in the glove box, treat the rekey as urgent. Call early in the day, and until we arrive, keep the deadbolt thrown and switch the garage opener to its lock or vacation mode.

Service in March Air Reserve Base

March Air Reserve Base is about 25 miles from our San Bernardino base, roughly 29 minutes in light traffic via University Parkway to I-215 South through San Bernardino, Colton and Grand Terrace, along the shared 60/215 stretch through Riverside past Box Springs. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Most trips into March Air Reserve Base use Trautwein Road for at least part of the drive, and the technician keeps an eye on live traffic along the way so the arrival estimate you heard on the phone stays honest.

About March Air Reserve Base: Civilian flights at the joint-use March Inland Port Airport are capped at 21,000 operations a year, and military aircraft keep priority on the runway.

Planning a rekey in March Air Reserve Base?

Call (951) 903-3193 and tell us how many doors you want on the new key and the brand of the locks if you know it. We'll quote the rekey before any work starts.