Get a Smart Deadbolt Fitted to Your Lakewood Door, Not Just Bolted On

What to know first in Lakewood

Measurements decide how smart deadbolt installation goes, and they're all quick to check. The face bore is almost always 2-1/8 inches and the edge bore 1 inch. Backset, from the door edge to the center of the face bore, is 2-3/8 or 2-3/4 inches, and most deadbolts adjust between the two. Door thickness runs from 1-3/8 to 1-3/4 inches on standard doors, while thicker doors need an extension kit or a different model. Handing matters on a few products. Then there is the interior clearance: the motor housing is larger than a plain thumbturn, so we check the distance to your handle and to any trim. Narrow-stile glass doors and French doors often can't take a smart deadbolt, and some mortise-lock doors in older Lakewood homes need a different style of lock altogether. We take these measurements before quoting, not after. A sketch with the numbers on it and two photos of the door are often all we need to confirm the lock over the phone.

Work included on a typical visit

• Reinforced strike plates and long-screw frame anchoring. A smart deadbolt shouldn't be held in by half-inch screws. We replace the stock strike with a reinforced plate and drive three-inch screws through the jamb into the framing. This is the cheapest meaningful security upgrade on most doors, and it also steadies the bolt's alignment.
• Door alignment and bolt travel correction. A bolt that rubs the strike makes a motor work harder, so we correct it at the source. That can mean tightening hinge screws, shimming a hinge, deepening the strike hole, moving the strike a hair or planing a tight edge, whichever matches the way your door actually sits.
• New deadbolt holes in doors that never had one. Some doors, especially secondary entries and older interior-style doors, have only a knob latch. We can add a deadbolt properly: mark the height above the handle, cut the 2-1/8 inch face bore with a hole saw and the 1 inch edge bore with a jig, then fit the lock and strike.
• Sidelights, glass panels and double-cylinder deadbolts. Old double-cylinder deadbolts, which need a key on both sides, are common near glass. They trap people in a fire, and modern building codes expect a main exit that opens from inside without a key. A smart deadbolt with a thumbturn avoids that, and we explain the tradeoffs before you decide.
• Fixing a smart deadbolt that jams, stalls or won't extend. A lock that beeps, flashes a jam error or stops short of full extension is usually telling you about the door. We check cable routing, mounting torque, strike depth, and alignment, and recalibrate the lock once the mechanics are right. Often the fix takes minutes once we find the cause.

Local factors in Lakewood

Family doors take a beating: slammed by kids, leaned on by groceries, rattled by the dog. Smart deadbolt installation in a busy house should start with the frame, because that abuse punishes the strike and hinges more than the lock. We reinforce the frame, set auto-lock so the door secures itself when everyone runs in and out, and give children a code they can learn quickly. The goal is a front door that works without nagging reminders. Teach everyone the manual thumbturn too, so a dead battery never traps a child inside.

Many older Lakewood homes have thick, dried-out doors, a deadbolt added later in a hurry, and frames that have moved with the house. We measure the bores, repair or re-bore as needed, and fit a reinforced strike before the motor goes in. A few older homes still have mortise locks, where a standard smart deadbolt won't fit, and we'll describe the alternatives instead of cutting up an original door. If the original hardware is worth keeping, tell us, and we'll plan the work around it.

In rentals, the lock belongs to the unit and a tenant's changes need approval. Civil Code 1941.3 requires working deadbolts on main swinging entry doors, so a smart deadbolt that replaces one must act as a real deadbolt, with a way in that doesn't depend on a phone. We install with written permission, and keep the original deadbolt available for reinstallation at move-out when the lease asks for it. Management may also want a copy of any master code, so we agree that in advance.

Common situations

• Picture a family in Lakewood with young kids who ride bikes in and out all afternoon, so the deadbolt gets left unlocked more often than anyone admits. A smart deadbolt with auto-lock fixes that if it's set properly. We'd pick a delay long enough to wheel a bike through, test it with the door closing naturally, and teach the kids a code that's easy to remember.
• A steel door with a crushed bore: an old break-in attempt left the edge bore deformed, and the previous deadbolt only worked by luck. A new smart deadbolt can't seat properly in that. We'd reshape or sleeve the bore, add a reinforcing plate, replace the damaged strike, and then fit the lock. Skipping that prep means an expensive lock held in by damaged metal.
• Say a new build in Mayfair came with a builder-grade deadbolt and a strike plate held by half-inch screws. The buyers want a smart deadbolt and a safer frame. We'd install the smart lock, upgrade the strike with three-inch screws into the stud, and check the hinge-side screws too. The visit adds little time and removes the weakest point on the door.
• A typical call: a 1970s house off I-605 with a solid-wood door and a deadbolt set at a 2-3/8 inch backset. The new smart deadbolt arrives set for 2-3/4. We'd twist the latch to the right length, check that the bolt lines up with the old strike, and confirm the interior housing clears the knob. Left unadjusted, the bolt would simply have missed its target.

Step by step with Julian's Locksmith

1. Identify the door and the deadbolt you want. Call (951) 903-3193 to start smart deadbolt installation. Give us the lock's model number, or tell us which you're considering, and describe the door: wood, steel, fiberglass or glass, and what handle it has. Two photos, one of the door edge and one of the inside around the deadbolt, let us flag problems before we arrive.
2. Measure the bores, backset, thickness and handing. On site, we measure the face bore, edge bore, backset and thickness, and check which way the door swings. Most are standard. If something isn't, such as a 2-1/4 inch thick door or an oversized bore, we know before the box is opened.
3. Remove the old bolt and repair the prep. The old deadbolt comes out, and the door gets cleaned and checked. Unused holes are filled, loose edge plates re-secured and crushed bores reshaped. The aim is a clean, solid starting point for a motor that has to work every day.
4. Set the bolt, strike and frame. Weatherstripping, hinge screws and the gap around the door all get checked now. If a seal pushes the door away from the strike, or a hinge has dropped, we correct it. Doing the mechanics first makes the later steps quick and quiet.
5. Connect the lock, calibrate and cycle. Calibration teaches the lock where the bolt starts and stops. We run it with the door open, then closed against the strike. If the results differ, something is dragging, and we go back and correct it before moving on.
6. Program, test with the door closed, and hand over. Now we program codes: a master code for you, user codes for family, and anything scheduled. We set auto-lock timing, volume and alerts, and add the lock to your phone if it connects. Then we run a full test with the door shut.

Pricing factors

• The model and its grade. If you buy the lock yourself, our charge covers installation, strike work and programming, not the hardware. If we supply the lock, its cost is listed separately. Either way you see two clear lines: the hardware and the work. Ask us to price both ways if you are undecided.
• Strike, frame and alignment work. If the frame is sound and the door hangs true, alignment is quick. If the door has dropped or the frame has shifted, correction takes time. We show you the cause, whether it's a loose hinge or a settling wall, and quote the fix.
• Who supplies the lock, programming and timing. Whether you bring the lock or we do, our labor is quoted separately from the hardware. If the lock you bought isn't a good fit, we tell you before we start. Programming a handful of codes is part of setup; elaborate schedules and long user lists take longer.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Lakewood.

What to do before we arrive

• Program a master code and write it down somewhere safe, away from the door. Change the factory default code right away. Set separate user codes for each person so you can remove them one at a time. A single shared code is easy to set up and painful to undo.
• Take photos before disassembly: the edge of the door, the inside around the lock, the strike and the frame. If anything goes wrong, you can see how it was. The photos also help us confirm a fit over the phone before we visit you in Lakewood.
• Check the clearance between the motor housing and your handle before drilling. Hold the interior assembly against the door and swing the handle. If they touch, a slimmer model, a different handle or a slightly different position will save you a headache. Measure first and install second.
• Keep the physical key even if you love the keypad. Store a spare outside the house with someone you trust, not under a mat. A smart deadbolt's backup is only useful if it works, so test it once after installation instead of assuming it does.

What not to do

• Keeping a double-cylinder deadbolt on a glass door because it feels safer. It can trap people who can't find the key in a fire, and building codes expect the main exit to open without one. A thumbturn lock, glass film and good lighting are a safer combination.
• Skipping the backup. A keypad lock with dead batteries and no key is a lockout waiting for a bad moment. Keep the key, know where the emergency terminals are, and test both once so you're sure they work. Keep a fresh 9-volt battery in a drawer, since many emergency terminals depend on one.
• Reusing short strike screws. Half-inch screws hold a strike to thin trim, not the framing, so a kick splits the jamb no matter how fancy the lock is. Three-inch screws cost very little and make a real difference. The extra screws take only minutes to install.

Getting to Lakewood

Lakewood is about 62 miles from our San Bernardino base, roughly 68 minutes in light traffic via University Parkway to I-215 South. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Once the evening commute thins out on Pioneer Boulevard, drive times usually shrink. That makes an evening call before closing a practical option for non-urgent jobs that you couldn't fit into the workday.

About Lakewood: The city covers about 9.5 square miles, with roughly 150 miles of streets, 300 miles of sidewalks and more than 36,000 trees along its streets and in its parks.

Smart lock help in Lakewood?

Call (951) 903-3193 with the lock's brand and model and what it's doing, or what you'd like installed. We'll tell you what can be done on-site and quote it before any work starts.