Magnetic Lock Installation in Covina

Magnetic Lock Installation in Covina: what to expect

A magnetic lock has two parts. The electromagnet, a steel housing with a coil inside, mounts to the frame, usually on the header above the door. The armature plate, a flat piece of steel, mounts to the door at the matching spot. When the coil is energized, the plate is pulled onto the magnet face with a rated holding force, commonly around 600 pounds on single-door models and 1,200 pounds or more on heavy-duty ones. Cut the power and the magnetism collapses, so there is nothing to retract and nothing to turn. The plate sits on a flexible bushing so it can seat flat against the magnet even if the door moves a little. Small things matter. A gap the thickness of a business card cuts holding force, paint or rust on the faces weakens the grip, and a plate that is out of alignment can leave a door that looks locked but pulls open with a firm tug. Good magnetic lock installation is mostly alignment, solid fastening and clean wiring.

How we can help in Covina

• Double doors and paired magnets. On a double door, one weak side defeats the whole opening. We match the holding force to the heavier leaf, mount each plate where the door is stiff, and test by pulling at the weakest point. Wiring both locks on a single release makes them behave as one door.
• Exit sensors and push buttons. A motion sensor above the door detects someone leaving and cuts power so the door opens. A push button, mounted near the door and wired to interrupt power directly, gives a second route out. We aim the sensor at the exit side and test it with people walking, carrying items and moving slowly.
• Power supplies, battery backup and surge protection. Battery backup keeps a maglock holding through short outages and brownouts, though the batteries wear out and the door will release once they are exhausted. We size the battery to your preferences, explain the limits, and put a replacement date on the enclosure so the backup is not forgotten.
• Readers, keypads and controllers. Standalone keypads handle one or two doors affordably; networked controllers manage many doors with schedules and logs. Either way the maglock follows the controller, and the exit devices stay on their own path. We write down codes, schedules and wiring so a new manager can take over.
• Door position switches, bond sensors and monitoring. A door-position switch tells the system whether the door is open or closed. A bond sensor, built into many magnets, reports whether the plate is actually seated against the magnet. Together they separate a door that is closed from one that is truly secure. We wire them to your controller or alarm if you want status or alerts.

What's different about Covina

Clinics and medical offices near Heritage Plaza Park use maglocks on records rooms, medication areas, labs and staff corridors. Some units, such as memory care or behavioral health, use delayed-egress locks under separate rules, which we don't improvise. For ordinary doors we focus on quiet release, door monitoring and clear exits, and we coordinate with your fire alarm service so that testing doesn't disrupt patients.

Apartment complexes use maglocks on glass-door fitness rooms, leasing offices, package rooms and clubhouses. Residents' expectations are simple: the door opens when they badge, and it opens from inside. Management needs logs, easy credential changes and a way to find a door left ajar. We install door-position switches and clear exit buttons, and we ask early where the fire marshal wants alarm integration.

Inland heat stresses power supplies, batteries and plastic parts. A supply in an unvented ceiling can run hot and fail, and backup batteries age faster. Glass and aluminum doors expand in afternoon sun, which can shift plate alignment slightly through the day. We mount supplies where air moves, check alignment hot as well as cool, and put a battery replacement date on the label.

Situations this covers

• Consider an office whose doors fell open during a blackout. The cause was a small plug-in adapter with no backup feeding two maglocks. We'd replace it with a fused, regulated supply, add battery backup so the doors hold through short outages, and recommend a mechanical keyed lock for off-hours security, so protection no longer hangs on one adapter.
• Say an earlier installer put a maglock on an office door with a card reader and nothing else. There is no exit button, no sensor and no link to the fire alarm. We'd survey the door, explain what is missing, add a sensor, a push button and a release relay, and tell you honestly which parts the building official will care about.
• Think of a boutique with frameless glass doors on patch fittings and a floor closer. The owner wants after-hours card access but doesn't want holes in the glass. We'd use a glass-door bracket to clamp the armature plate, mount the magnet on a header plate above the door, hide the cable in the soffit, and add a push button and sensor inside so the door always opens for anyone leaving.
• Take a warehouse pedestrian door that opens outward onto a loading yard off Badillo Street. Forklifts bump it, and the frame is thin. A maglock may not be the best choice, because the magnet needs solid anchoring and a flexing frame loses holding force. We'd weigh a strike or an electrified exit device first, and use a maglock only if the frame can be stiffened.

From your call to the finished job

1. Survey the door, header and exit path. On site we measure door thickness and swing, header depth and ceiling access for cable. We ask who uses the door, when and how, and where the fire alarm panel and power sources are. Photos before the visit help, but nothing replaces seeing the door.
2. Design the release path and quote. We decide which magnet or magnets, which brackets and which release devices the door needs: sensor, button, fire alarm relay and credentials. The written quote shows each piece and flags anything that needs an electrician, fire alarm contractor or building official before work begins.
3. Mount the magnet and armature plate. The magnet face and plate must meet flat. We check the gap, adjust the plate until contact is even, and clean both faces so no paint, dust or tape sits between them. Small gaps cost large amounts of holding force.
4. Run the power, sensors and fire alarm release. Wiring decides reliability. We use wire of the right gauge for the distance, land connections on terminals instead of twisting wires together, and fuse the supply. Exit devices get their own path, so one failed component can't trap anyone.
5. Program credentials and set the timers. Programming depends on the controller. A standalone keypad takes a few settings; a networked system takes a user list and schedules. We create the first credentials with you, show you how to add and delete them, and leave the settings recorded.
6. Test every release and hand over. Handover includes a short checklist: monthly button test, periodic cleaning of the plate and magnet face, and battery replacement every few years. We write the lock model, voltage and holding force on a label inside the enclosure, so future service doesn't start with guesses.

Pricing factors

• Door type and mounting hardware. Heavy glass, wide double doors and odd headers all add to hardware needs. We would rather quote a solid kit that holds than a cheap bracket that flexes, because a flexing bracket costs holding force and, sooner or later, trust.
• Holding force and number of leaves. Each additional leaf or door adds a lock, a plate, brackets and wiring. Several doors in one visit share survey time and programming, which lowers the cost per door, but we still quote each opening separately so you can approve some doors now and others later.
• Cable route and header access. Where power comes from affects cost as much as hardware. A supply close to the door is cheap; one across the building means heavier wire and more labor. Sometimes moving the supply saves more than any other decision. We look for the nearest ceiling space or closet during the survey.

Every job gets a clear quote before any work starts. Call (951) 903-3193 with the details and we'll tell you what to expect for your situation in Covina.

Advice before you book

• If you rent, ask the landlord in writing before anyone drills the frame. A maglock may need removal when you leave, so keep a copy of the wiring diagram, the model information and any hardware that was taken out. The next tenant, and your landlord, will thank you.
• Stand at the door and ask yourself: if the lights went out and I had never been here, could I leave? If the answer needs a sign, a hidden button or a staff member's help, the design isn't finished. Say so when you call us in Covina; we start with the exit.
• Review who holds access a few times a year. Cards and codes pile up as staff, vendors and contractors come and go, and every extra credential is a door that opens for someone. Remove what you no longer need and keep a short list of current holders.
• Keep banners, window film and signs off the header and away from the lock. Heat and adhesive can affect the magnet face and the sensor, and a sign can hide the release button. A tidy, visible door is a safer door.

What not to do

• Installing the lock without an exit plan. A maglock with a card reader and nothing else can trap people if the controller fails while the lock stays energized. A sensor, push button and fire alarm release aren't optional on exit doors, and an inspector will look for them.
• Mounting the magnet to a hollow, thin or flexible header. It may feel solid when installed and then give way under a hard pull. Anchor into steel, solid blocking or a backing plate that spreads the load across the frame.
• Using a maglock where the door must stay latched. Fire-rated doors, some stairwells and other openings need hardware that latches positively, which a maglock does not do. Ask your building department before you specify one. If you are not sure how your door is classified, look for a label on the edge of the door or frame.

Reaching Covina

Covina is about 39 miles from our San Bernardino base, roughly 45 minutes in light traffic via I-215 North to I-15 South. When you call, you get an arrival estimate based on where the technician is and the traffic at that moment.

Homes and businesses just off Grand Avenue are routine stops for us. Give the suite or unit number and any gate instructions, and say whether the van can park out front or should pull into a side lot.

About Covina: Surveyor Fred Eaton coined the name Covina, a blend of 'cove' and 'vine,' after noting the vineyards growing in the area.

Business lock or door work in Covina?

Call (951) 903-3193 with the address, the doors or hardware involved and when the site is open. We'll quote the job before any work starts and book a time within our hours that suits your schedule.