2024 Subaru Legacy Key Replacement

2024 Legacy key specs

The final Legacy generation uses the H chip in both of its key types. Lower trims have a four-button remote-head key with a side-cut blade, while upper trims have Keyless Access with push-button start. Subaru's bulletin lists a new key part number for 2020, and 2024 cars use a newer remote-head key with a thicker CR2025 battery. Smart fobs have a hidden emergency blade, and they are not interchangeable with the fobs of 2019 and earlier.

What's specific to the 2024 Legacy

The 2024 Subaru Legacy is the fifth of 6 model years in the Legacy BW (seventh generation) (2020–2025), so it shares its key system with the rest of that run, which makes replacement parts easy to source. At 2 years old, a 2024 Subaru Legacy is usually still on its original keys and fob batteries. The most common call for a car this new is a second key, since many buyers leave the dealer with only one, or a replacement after a lost fob.

Smart-key cars like the 2024 Legacy can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2024 Subaru Legacy

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2024 Subaru Legacy with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). Making a new smart key is mostly a programming job. The fob has to match the vehicle's FCC ID, frequency and chip, and then the keyless system must be told to accept it, normally through the OBD-II port. Depending on the platform, that can mean entering a PIN, waiting through a timed security procedure, or on some newer vehicles, using manufacturer online access. When every key is lost, certain models need a module removed and read on the bench. For your Subaru Legacy BW (seventh generation), we'll tell you which of those applies, and if a step is dealer-only, you'll hear it before we drive out. The emergency blade hidden inside the fob is cut by code during the same visit.

How the Subaru immobilizer works on the Legacy

• Subaru's bulletin lists the 2020 Legacy remote-head key as part 57497AN00A and the 2021 key as AN00B.
• The 2024 remote-head key, FCC ID CWTB1G496, takes a CR2025 battery and covers the 2024 Legacy and Outback.
• Smart fobs with FCC ID HYQ14AKB, part 88835XC00A, are listed for 2019-2024 Legacy, Outback and Ascent models.
• Subaru ended the Legacy after the 2025 model year.

Programming a 2024 Legacy key

Adding a key with one working key present is routine over OBD-II, and the remote is registered alongside the transponder. All-keys-lost is more involved on these DST-AES cars: it can usually be done with dedicated Subaru software or an emulator connected through the OBD-II port, and a few cars need a module read on the bench. We confirm coverage from your VIN, and if a dealer visit is the only route, we say so up front.

Spare keys are routine. All-keys-lost needs specialized Subaru software or emulators, and a few cars may need the dealer.

Lost every key to your Legacy?

With every key gone, the model year decides the job. A 2000-2004 Subaru, a Baja, or a base model built before its line got an immobilizer just needs a key cut by code or by decoding the door lock. On 4D62 cars from 2005 through 2011 and on remote-head cars of the G-chip years, we cut the blade, erase the missing keys and program new ones in one visit. Keyless Access cars of the G-chip years and every H-chip car are harder: some tools need a working key, so we use dedicated Subaru software or an emulator, and a few cars have to go to the dealer. Brand-new platforms, including the 2026 Outback and Subaru's electric models, are usually dealer jobs for now. We tell you plainly which route your car needs and check ID and proof of ownership before any work.

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Legacy can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru Legacy, ask us directly and you'll get a plain answer.

Legacy key battery

Battery details for the 2024 Legacy: CR2025 (2024 remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Legacy uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru Legacy keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Legacy key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• Between 2005 and 2008 Subaru fitted immobilizers by trim, so a base Forester or Impreza of those years may have no chip while the turbocharged version does. Check before buying blanks, because a chipless copy won't start an XT, WRX or STi.
• If a Keyless Access fob battery dies, the car can usually still be started with the backup method in the owner's manual, which uses the fob and the start button. The emergency blade hidden in the fob opens the driver's door.
• Used Subaru fobs sold online can arrive already programmed to another car. Ask whether a fob is new or reset to a blank state before you buy, and bring the part number and FCC ID from your old key so we can confirm the fit before programming.

Tips from a mobile locksmith

• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2024 Subaru Legacy key?

Don't wait until the last key disappears. If your Subaru Legacy is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.