2016 Subaru Legacy Key Replacement

2016 Legacy key specs

Most 2015-2019 Legacy sedans use a four-button remote-head key with a side-cut blade and the 80-bit G chip, a simpler blade than the previous car's laser-cut key. Upper trims, including the Limited, have Keyless Access with push-button start and a smart fob with a slide-out emergency key. Late-run remote-head keys look identical but differ inside: 2018 keys use a black button pod and 2019 keys a gray one, and they don't cross over.

What's specific to the 2016 Legacy

The 2016 Subaru Legacy is the second of 5 model years in the Legacy BN (sixth generation) (2015–2019), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 10 years old, a 2016 Subaru Legacy has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2016 Subaru Legacy

• Remote head key. Remote-head keys take a beating. The rubber button pad wears through, the plastic housing splits at the seam, and the blade can snap right at the head after years of being used as a pry tool or hanging from a heavy key ring. When the electronics inside are still healthy, we can often move the circuit board and chip into a new shell and cut a fresh blade to your code, which keeps the existing programming intact. If the board is cracked or water-damaged, a new key is the honest answer. Either way, for your 2016 Legacy, we open the old key and show you what's broken before recommending anything.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2016 Subaru Legacy open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Subaru immobilizer works on the Legacy

Subaru came to engine immobilizers later than most brands sold in the US, which keeps things simple for owners of early-2000s models: no 2000-2004 US Subaru has a transponder, so a correctly cut key starts the car. Subaru's own chart shows immobilizers arriving by model and trim from the 2005 model year. That year only the Forester XT, Impreza STi, Legacy GT and Outback XT and 3.0R had one. Every Legacy, Outback and Tribeca followed for 2006, the WRX joined the STi, the whole Impreza line had one by 2008 and the whole Forester line by 2009. The first systems use Texas 4D62 chips in side-cut keys. Subaru then moved to high-security laser-cut keys on 2008-2011 Imprezas, 2008-2014 WRX and STI models, 2009-2013 Foresters and 2010-2014 Legacy and Outback models. From the 2012 Impreza, an 80-bit Subaru G chip arrived in a side-cut remote-head key. The 2017 Impreza introduced the 128-bit Subaru H chip, which reached the Crosstrek for 2018, the Forester and Ascent for 2019 and the Legacy and Outback for 2020. Keyless Access smart keys began with the 2013 BRZ and the 2013-2014 Legacy and Outback.

• Supplier listings pair the black-pod remote-head key, part 57497-AL27A, with 2018 models and the gray-pod 57497-AL37A with 2019.
• Smart fobs listed for 2015-2017 Legacy models carry FCC ID HYQ14AHC at 315 MHz.
• Subaru's G-chip keys use an 80-bit Texas transponder that locksmith suppliers also label 4D82.

Programming a 2016 Legacy key

Both key types program over OBD-II, and the remote functions are added in the same session when a working key is present. Smart fobs must be new or reset to a virgin state. With every key lost, remote-head cars are handled with Subaru's immobilizer data, while smart-key cars can need special tools or the dealer. On 2018-2019 remote-head keys, we confirm the pod color inside your old key before ordering a replacement.

Spare keys are routine. All-keys-lost on remote-head cars is usually fine, but Keyless Access cars can need special tools or the dealer.

Lost every key to your Legacy?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru Legacy can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Subaru Legacy requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru Legacy, ask us directly and you'll get a plain answer.

Legacy key battery

Battery details for the 2016 Legacy: CR1620 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your Legacy uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru Legacy keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your Legacy, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a Legacy key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Subaru Legacy is the most involved of all, both in the part itself and in the programming.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Remote-head key shells tend to crack at the blade root after years on a heavy keyring. The remote board and transponder can usually be moved into a new shell with a freshly cut blade, which often costs less than a complete new key.
• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• Between 2005 and 2008 Subaru fitted immobilizers by trim, so a base Forester or Impreza of those years may have no chip while the turbocharged version does. Check before buying blanks, because a chipless copy won't start an XT, WRX or STi.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2016 Subaru Legacy key?

Need a key for your 2016 Subaru Legacy? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.