2018 Subaru BRZ Key Replacement

2018 BRZ key specs

Premium BRZs from 2013 to 2020 use a four-button remote-head key with a Toyota-type TR47 side-cut blade and a G chip. Limited models have Keyless Access with push-button start, using a smart fob with an inside-cut emergency key. Subaru's bulletin shows the remote-head key as part 57497CA110 for 2013-2014 and CA310 from 2015, and the emergency key changing in 2015 too, so early and late cars take different parts.

What's specific to the 2018 BRZ

The 2018 Subaru BRZ is the sixth of 8 model years in the BRZ ZC6 (first generation) (2013–2020), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 8 years old, a 2018 Subaru BRZ has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2018 Subaru BRZ

• Remote head key. Remote-head keys look similar across many vehicles, but the electronics inside are not interchangeable. Getting the right one for a Subaru BRZ means matching the FCC ID and part number printed on the back or inside the case, the operating frequency, which is commonly 315 MHz on US-market cars, the transponder type, and the button layout. A trim with remote start or a power liftgate may use a four- or five-button version where a base trim uses three. We check those details against your VIN and your existing key, if you have one, before cutting the blade. A wrong match can look perfect and still refuse to program.
• Smart proximity key (push-to-start). Proximity keys bring a security trade-off worth understanding. Because the fob is always listening, thieves with relay equipment can stretch its signal from inside your house to the car in the driveway. Keeping the fob away from exterior walls, or in a signal-blocking pouch, closes that gap, and some fobs offer a sleep mode described in the owner's manual. If a smart key for your 2018 Subaru BRZ is lost or stolen, programming a replacement is the moment to delete the missing fob from the car's memory. And be wary of used fobs from online sellers: a lot of them are locked to the vehicle they came from and can't be reprogrammed to yours.

How the Subaru immobilizer works on the BRZ

• The 2013-2014 BRZ remote-head key, part 57497-CA110, uses FCC ID HYQ12BBY and a CR2016 battery.
• Subaru's bulletin lists a 5+5 laser emergency key for the 2013-2014 BRZ smart key and a thinner 4+4 key from 2015.
• The HYQ14AHC smart key, part 88835-AL04A, is listed for the BRZ among Subarus of 2014-2017.

Programming a 2018 BRZ key

Both key types program through the OBD-II port, with the remote side handled in the same session when a working key is present. A smart fob must be new or reset to blank, and its inside-cut emergency key needs an internal-cut machine, while the remote-head blade is cut on a standard machine. With every key lost, remote-head cars are usually fine, and Keyless Access cars may need special tools or the dealer.

Spare keys are routine. All-keys-lost on remote-head cars is usually fine, but Keyless Access cars can need special tools or the dealer.

Lost every key to your BRZ?

With every key gone, the model year decides the job. A 2000-2004 Subaru, a Baja, or a base model built before its line got an immobilizer just needs a key cut by code or by decoding the door lock. On 4D62 cars from 2005 through 2011 and on remote-head cars of the G-chip years, we cut the blade, erase the missing keys and program new ones in one visit. Keyless Access cars of the G-chip years and every H-chip car are harder: some tools need a working key, so we use dedicated Subaru software or an emulator, and a few cars have to go to the dealer. Brand-new platforms, including the 2026 Outback and Subaru's electric models, are usually dealer jobs for now. We tell you plainly which route your car needs and check ID and proof of ownership before any work.

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Dealers have one clear advantage: direct access to the manufacturer's own systems. Some newer vehicles tie key programming to online authorization that only a dealer can use, and certain all-keys-lost situations on specific platforms still require it. A good locksmith knows where those lines are. Where we can do the job, we use professional programming equipment that talks to the same immobilizer and keyless systems through the OBD-II port, and in many cases the result is identical: a properly registered key that starts the car. Where we can't, we can often still help by opening the vehicle, cutting a mechanical blade from code, or helping you gather what the dealer will ask for so that visit goes smoothly. For your Subaru BRZ, ask us directly and you'll get a plain answer.

BRZ key battery

Battery details for the 2018 BRZ: CR2016 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your BRZ uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Subaru system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a BRZ key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your BRZ came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• All keys lost or adding a key. On some vehicles, losing the last key changes the programming entirely, from a quick add-key procedure to a full immobilizer reset or a module read on the bench. That extra labor shows up in the price, and it's the strongest argument for keeping a spare in the house.
• Programming complexity and security access. Two cars with similar-looking keys can program very differently. Newer platforms often guard key programming behind encrypted access or paid credentials, while older systems allow straightforward OBD-II pairing. We check the exact procedure for your VIN before quoting, so the number reflects the real work involved.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Between 2005 and 2008 Subaru fitted immobilizers by trim, so a base Forester or Impreza of those years may have no chip while the turbocharged version does. Check before buying blanks, because a chipless copy won't start an XT, WRX or STi.
• Used Subaru fobs sold online can arrive already programmed to another car. Ask whether a fob is new or reset to a blank state before you buy, and bring the part number and FCC ID from your old key so we can confirm the fit before programming.
• Subaru smart keys use different emergency blades. Subaru's bulletin lists a 5+4 laser-cut emergency key for the 2014-2015 Forester, the 2014 Crosstrek Hybrid and the 2015 WRX, and a thinner 4+4 key on later cars. Cut the blade to match your fob, not just the model name.
• If a Keyless Access fob battery dies, the car can usually still be started with the backup method in the owner's manual, which uses the fob and the start button. The emergency blade hidden in the fob opens the driver's door.

Tips from a mobile locksmith

• Never hide a spare key or fob on the outside of the car. Magnetic boxes in wheel wells and under bumpers are the first places a thief checks, and with a proximity fob, a hidden key can let anyone open the doors and drive away. Keep the spare at home or with someone you trust.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2018 Subaru BRZ key?

Don't wait until the last key disappears. If your Subaru BRZ is down to one key, or the one you have is falling apart, call (951) 903-3193. We're a licensed California locksmith, license LCO7891, serving Southern California and the rest of the Inland Empire with mobile car key service every day from 6:30 a.m. to 11:30 p.m.