2013 Subaru BRZ Key Replacement

2013 BRZ key specs

Premium BRZs from 2013 to 2020 use a four-button remote-head key with a Toyota-type TR47 side-cut blade and a G chip. Limited models have Keyless Access with push-button start, using a smart fob with an inside-cut emergency key. Subaru's bulletin shows the remote-head key as part 57497CA110 for 2013-2014 and CA310 from 2015, and the emergency key changing in 2015 too, so early and late cars take different parts.

What's specific to the 2013 BRZ

2013 was the first model year of the BRZ ZC6 (first generation). Early-production cars sometimes use different part numbers than later ones, so for a 2013 Subaru BRZ we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. At roughly 13 years old, a 2013 Subaru BRZ has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Smart-key cars like the 2013 BRZ can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2013 Subaru BRZ

• Remote head key. A remote-head key puts two separate systems in one piece: a cut blade with a transponder chip that the immobilizer reads, and a small circuit board with buttons that signals the body control module to work the door locks. On a 2013 Subaru BRZ with this style of key, each side is programmed separately. That explains some confusing failures. If the remote stops working but the car still starts, the problem is usually the battery or the remote board. If the buttons work but the engine won't run, look at the chip side. Knowing which half failed tells us whether you need a repair, a reprogram or a whole new key.
• Smart proximity key (push-to-start). A smart or proximity key lets a 2013 Subaru BRZ open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Subaru immobilizer works on the BRZ

Subaru came to engine immobilizers later than most brands sold in the US, which keeps things simple for owners of early-2000s models: no 2000-2004 US Subaru has a transponder, so a correctly cut key starts the car. Subaru's own chart shows immobilizers arriving by model and trim from the 2005 model year. That year only the Forester XT, Impreza STi, Legacy GT and Outback XT and 3.0R had one. Every Legacy, Outback and Tribeca followed for 2006, the WRX joined the STi, the whole Impreza line had one by 2008 and the whole Forester line by 2009. The first systems use Texas 4D62 chips in side-cut keys. Subaru then moved to high-security laser-cut keys on 2008-2011 Imprezas, 2008-2014 WRX and STI models, 2009-2013 Foresters and 2010-2014 Legacy and Outback models. From the 2012 Impreza, an 80-bit Subaru G chip arrived in a side-cut remote-head key. The 2017 Impreza introduced the 128-bit Subaru H chip, which reached the Crosstrek for 2018, the Forester and Ascent for 2019 and the Legacy and Outback for 2020. Keyless Access smart keys began with the 2013 BRZ and the 2013-2014 Legacy and Outback.

• The 2013-2014 BRZ remote-head key, part 57497-CA110, uses FCC ID HYQ12BBY and a CR2016 battery.
• Subaru's bulletin lists a 5+5 laser emergency key for the 2013-2014 BRZ smart key and a thinner 4+4 key from 2015.
• The HYQ14AHC smart key, part 88835-AL04A, is listed for the BRZ among Subarus of 2014-2017.

Programming a 2013 BRZ key

Both key types program through the OBD-II port, with the remote side handled in the same session when a working key is present. A smart fob must be new or reset to blank, and its inside-cut emergency key needs an internal-cut machine, while the remote-head blade is cut on a standard machine. With every key lost, remote-head cars are usually fine, and Keyless Access cars may need special tools or the dealer.

Spare keys are routine. All-keys-lost on remote-head cars is usually fine, but Keyless Access cars can need special tools or the dealer.

Lost every key to your BRZ?

1. Gather your documents and the VIN. Call with the year, make, model and VIN if you can read it through the windshield, plus where the car is parked. Those details let us confirm whether your Subaru BRZ can be done on-site and bring the right key, so the first trip is the only trip.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. Originating a key means building it without a sample. The door lock usually reveals most of the cuts; any it doesn't are worked out by test-cutting and trying the ignition or a second lock. The finished blade should feel like a factory key, not a forced fit.
4. Program the key to the immobilizer. Next, the new key is introduced to the car's security system. Many vehicles allow this through the OBD-II port with a PIN or security procedure. Some all-keys-lost cases require reading a module on the bench, and a few platforms only allow dealer programming, which we'll tell you up front.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

The biggest difference between a dealership and a mobile locksmith is where the work happens. A dealer programs keys in its service bay, so if every key is lost, the car usually has to be towed there, and you work around the service department's schedule and the time it takes to order a key by VIN. Julian's Locksmith brings the cutting machine, key blanks and programming equipment to the car, whether it sits in your driveway, a workplace lot or a parking structure. For a 2013 Subaru BRZ we can program on-site, that means no tow and no shuttle rides back and forth. The trade-off is real, though: on vehicles where only the dealer can program keys, a tow or appointment may still be necessary, and we'll say so before you spend anything on our visit.

BRZ key battery

Battery details for the 2013 BRZ: CR2016 (remote-head key); CR2032 (smart fob). Swap cells one at a time and match each one exactly; if a key still fails with a fresh battery, the board, buttons or programming may be the problem, which we can test on site.

How the job works

1. Identify the exact key your BRZ uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Subaru BRZ keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. Programming tells the car's computers that the new key belongs to the vehicle. Transponder chips are added to the immobilizer, remote buttons to the body control module, and proximity fobs to the keyless system. If a step requires dealer-only access on your BRZ, you'll have heard that before we arrived, not halfway through the job.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a BRZ key

• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• All keys lost or adding a key. Adding a key while a working one is in hand is the simpler job. With every key gone, we may have to open the car, decode a lock to originate the cuts, and run a longer programming routine, so all-keys-lost work takes more time and costs more.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Subaru system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Because we come to you, the distance from our San Bernardino base and the time of the call play a part. So does anything we find along the way, such as a worn ignition cylinder or a seized door lock. You hear about each item and get a quote before we start work.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Subaru key problems

• Remote-head keys from 2012 through at least 2022 mostly run on a CR1620 cell, while Keyless Access fobs from 2014 on take a CR2032. The 2024 remote-head key moved to a thicker CR2025. Inland Empire summer heat shortens coin-cell life, and shrinking range is the usual warning.
• Subaru remotes of one era were built on two frequencies under different FCC IDs: CWTWB1U811 at 315 MHz and CWTWBU766 at 433.92 MHz. Both appear on remote-head keys for 2010-2015 Subarus, so match the part number printed on your old key before you buy a replacement.
• If a Keyless Access fob battery dies, the car can usually still be started with the backup method in the owner's manual, which uses the fob and the start button. The emergency blade hidden in the fob opens the driver's door.

Tips from a mobile locksmith

• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2013 Subaru BRZ key?

The quickest route to a working key for a 2013 Subaru BRZ starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.