2019 Ram ProMaster City Key Replacement

2019 ProMaster City key specs

The ProMaster City uses a flip key with a SIP22 laser-cut blade and three buttons: lock, unlock and rear door. Suppliers list the LTQF12AM433TX or 2ADFTF12AM433TX FCC ID for these vans, tied to a Delphi body control module, and the ID46 chip sits inside the key head. A key built for a Marelli-module Fiat or full-size ProMaster looks almost identical but will not program. Catalog coverage is clearest for 2015-2018 vans, so on later ones we read the FCC ID inside your key before ordering.

What's specific to the 2019 ProMaster City

The 2019 Ram ProMaster City is the fifth of 8 model years in the ProMaster City VM (Doblo-based) (2015–2022), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

A 2019 Ram ProMaster City is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up.

Key options for the 2019 Ram ProMaster City

• Flip (switchblade) key. When a flip key is lost rather than broken, the replacement starts from scratch. For a Ram ProMaster City, we confirm the FCC ID, frequency and chip type from the VIN and any remaining key, cut the blade by code, then program both the transponder for the immobilizer and the remote buttons for the doors. Some platforms accept a new flip key through the OBD-II port in a single session; others need a security PIN or a module read before they'll take a new key. Aftermarket flip keys vary a lot in quality, especially the hinge mechanism, so we'll tell you which options we trust for your 2019 ProMaster City and which we don't.

How the Ram immobilizer works on the ProMaster City

Ram became a stand-alone brand for the 2011 model year, separating the pickups from Dodge, and the badge now also covers the C/V cargo van, the ProMaster vans and the 2011 Dakota. The full-size pickups of 2011 and 2012 start with a Fobik, a bladeless remote that plugs into an ignition node in the dash; the node reads a Philips ID46 transponder inside the fob before the engine is allowed to run. The 2013 update kept the Fobik on most trucks but moved to a new fob family, and Keyless Enter 'n Go, with a proximity fob and a start button, was available on many higher trims. The 1500 Classic carried that Fobik all the way to 2024. The redesigned 1500 and Heavy Duty trucks of 2019 switched to push-button smart keys with Hitag AES (4A) transponders, learned by a radio-frequency hub and shielded by a security gateway at the diagnostic port. The 2011 Dakota kept a traditional cut transponder key. The vans follow Fiat practice instead: the ProMaster and ProMaster City launched with SIP22 flip keys carrying an ID46 chip, and the full-size ProMaster moved to a push-button smart key for 2022.

• Its SIP22 flip key is a close relative of the Fiat 500's, though the remote must match the van's body control module.
• A broken flip-key hinge can often be fixed by moving the electronics into a new shell and blade.
• The remote's third button unlocks the rear cargo doors on their own.

Programming a 2019 ProMaster City key

As with other Fiat-derived vehicles, an aftermarket key for the ProMaster City usually needs its transponder pre-coded with specialist equipment, then it is programmed through the OBD-II port using the van's PIN, along with the remote buttons. Spares are a routine job with that equipment. All-keys-lost is often workable on site, but some vans need extra module steps, so we confirm the details first.

Spare keys are routine. Remotes need specialist programming, and some all-keys-lost cases need module work or the dealer.

Lost every key to your ProMaster City?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ram ProMaster City requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. Once the car starts, we remove the lost keys from memory wherever the system allows, so they can't start the engine if someone finds them. Making a second key during the same visit costs much less than a repeat all-keys-lost call down the road.

Why a spare key pays for itself

• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.
• When you sell or trade in the vehicle, buyers and dealers expect two keys. A missing key can come up during an appraisal or a private-sale negotiation, so having both on hand keeps the conversation about the car, not about what it will cost the next owner to replace one.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your ProMaster City and your schedule.

ProMaster City key battery

If a new CR2032 doesn't bring the fob back, the battery wasn't the problem. Common culprits include a battery holder whose solder joints have cracked from drops, contacts corroded by moisture, worn rubber button pads that no longer reach the circuit, or a board damaged by water. We can test whether the fob is transmitting at all and inspect the board closely. Sometimes a new shell or a resoldered holder solves it; sometimes the fob has to be replaced and programmed. Meanwhile, the car can usually still be started with the fob held at the backup spot described in the owner's manual.

How the job works

1. Identify the exact key your ProMaster City uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ram keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ram system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a ProMaster City key

• The type of key. Price follows complexity. The more the key does, the more it costs to replace: brass blade, then chip, then remote buttons, then full keyless entry and push-button start. If your ProMaster City came with different key styles by trim, the one your car actually uses is the one that sets the quote.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ram system adds equipment time and labor to the job.
• Travel, timing and extra repairs. Sometimes a key problem is really a lock problem: an ignition that won't turn even with the right key, or a door cylinder that has been jammed for years. Fixing those is separate work. We point them out, explain the options, and quote the whole job up front so the bill holds no surprises.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ram key problems

• A fob bought from a parts counter or online usually arrives with an uncut emergency key. Left uncut, it cannot open the door when the fob or the truck battery dies, so have it cut when the fob is programmed.
• Used Ram fobs sold online are locked to the truck they came from. They only program after being unlocked or re-flashed, and many never work at all, so a new or properly prepared fob is the safer purchase.
• The Fobik ignition node on 2011-2018 Rams and the 1500 Classic can stop reading the fob, refuse to turn, or trap the fob in the dash. We test the node first, because a new fob will not fix a failing reader.

Tips from a mobile locksmith

• If your vehicle has a proximity key, think about where it sleeps at night. A fob hanging by the front door can sit within range of relay equipment used to open and start cars from outside. A drawer deeper inside the house, a signal-blocking pouch, or the fob's own sleep mode reduces that risk considerably.
• Be careful with discount fobs from online marketplaces. A listing may match your remote's shape while using a different frequency, chip or FCC ID, and many used smart keys are locked to their original vehicle. If you already bought one, send us the listing or a photo before the visit so nobody pays for a programming attempt that can't work.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Not every situation fits the simple case, so here's how we handle the common exceptions. For a leased or financed vehicle, a registration that lists you as the registered owner or lessee works with your ID. If you just bought the car, bring the signed title or bill of sale along with your ID. For a company or fleet vehicle, we need written authorization from the business plus the driver's ID. If the car belongs to a family member, the registered owner should be present or provide signed permission and a copy of their ID. Rental vehicles go through the rental company.

Need a 2019 Ram ProMaster City key?

The quickest route to a working key for a 2019 Ram ProMaster City starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.