2017 Ram ProMaster City Key Replacement

2017 ProMaster City key specs

The ProMaster City uses a flip key with a SIP22 laser-cut blade and three buttons: lock, unlock and rear door. Suppliers list the LTQF12AM433TX or 2ADFTF12AM433TX FCC ID for these vans, tied to a Delphi body control module, and the ID46 chip sits inside the key head. A key built for a Marelli-module Fiat or full-size ProMaster looks almost identical but will not program. Catalog coverage is clearest for 2015-2018 vans, so on later ones we read the FCC ID inside your key before ordering.

What's specific to the 2017 ProMaster City

The 2017 Ram ProMaster City is the third of 8 model years in the ProMaster City VM (Doblo-based) (2015–2022), so it shares its key system with the rest of that run, which makes replacement parts easy to source.

At roughly 9 years old, a 2017 Ram ProMaster City has usually seen real wear. Ignition and door cylinders on high-mileage cars wear along with the key, so we cut new keys to factory code rather than copying a worn key. Fob cases crack, buttons wear through and solder joints loosen at this age, so a new shell or a replacement remote often beats repairing the old one. Many have changed hands more than once, so erasing keys you can't account for is worth doing during the visit.

Key options for the 2017 Ram ProMaster City

• Flip (switchblade) key. The hinge is the weak point on most flip keys. The pivot pin loosens, the spring loses tension, the release button sticks, and eventually the blade either won't lock open or flops out on its own. Carrying the key half-open in a pocket speeds that wear along. If the electronics are healthy, a replacement shell with a new hinge and pin often brings a 2017 Ram ProMaster City flip key back to crisp action: we transfer the board and chip, move or recut the blade, and test every function. If the board has broken solder joints or water corrosion, we'll show you the damage and quote a new key instead.

How the Ram immobilizer works on the ProMaster City

• Its SIP22 flip key is a close relative of the Fiat 500's, though the remote must match the van's body control module.
• A broken flip-key hinge can often be fixed by moving the electronics into a new shell and blade.
• The remote's third button unlocks the rear cargo doors on their own.

Programming a 2017 ProMaster City key

As with other Fiat-derived vehicles, an aftermarket key for the ProMaster City usually needs its transponder pre-coded with specialist equipment, then it is programmed through the OBD-II port using the van's PIN, along with the remote buttons. Spares are a routine job with that equipment. All-keys-lost is often workable on site, but some vans need extra module steps, so we confirm the details first.

Almost every Ram key job runs through the immobilizer PIN. On Fobik-era trucks and vans, professional tools can usually read it through the OBD-II port and add a fob in one session, which also pairs the lock, unlock and remote start buttons. Newer Rams add a security gateway module that blocks key programming at the diagnostic port until the tool is authenticated online or connected behind the gateway with a bypass cable. The 2019-and-later smart keys are learned by the radio-frequency hub, and the replacement has to match the FCC ID and part-number family of your original, which differ between the 1500 and the Heavy Duty trucks. The Fiat-derived ProMaster and ProMaster City flip keys need specialist equipment, because the remote's own memory has to be written before the van will learn it. Ram fobs are also not plug-and-play from an online marketplace: a used fob only programs after it has been unlocked or re-flashed.

Spare keys are routine. Remotes need specialist programming, and some all-keys-lost cases need module work or the dealer.

Lost every key to your ProMaster City?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. If the car is locked, we open it with non-destructive tools such as an inflatable wedge and a long-reach rod, or by picking the door lock. Some vehicles need a careful approach to avoid triggering the alarm, which can interfere with programming later.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ram ProMaster City requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• Two drivers sharing one key is a daily negotiation. A second key lets a partner, teenager or coworker use the vehicle without handing keys back and forth in parking lots, and it means one person losing their key ring doesn't leave the whole household stuck.
• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your ProMaster City and your schedule.

ProMaster City key battery

A fob battery rarely dies all at once. The warning signs build: you have to get closer to the car before the doors respond, the dash shows a key battery or key-not-detected message, or the push-button start only works with the fob held near the button. Inland heat speeds that decline, especially for fobs left in a hot cabin or on the dashboard. Keep a spare CR2032 at home in a cool drawer, sealed in its original package, and buy from a busy store where stock turns over quickly. A cell that sat on a shelf for years may arrive already partly spent.

How the job works

1. Identify the exact key your ProMaster City uses. Every job starts with the VIN, the trim and a look at any key you still have. From those we confirm the keyway, the transponder or smart-key chip, the remote frequency, the FCC ID and the button layout. Two Ram ProMaster City keys that look identical can carry different electronics, so this step keeps the wrong part from ever reaching the car.
2. Verify ownership before any work. Before cutting or programming, we compare your government photo ID with the vehicle registration or title and check that the VIN on the paperwork matches the VIN on the dash. If the registration is locked inside, we open the car first, confirm the documents, and only then make the key.
3. Get the key code or decode the lock. If you still have a working key, we can read its cuts directly and check them against the factory depths for the Ram keyway. A worn key gets corrected back to spec during this step, so the new key turns crisply instead of reproducing years of wear in a fresh piece of metal.
4. Cut the blade on-site. Cutting happens right beside your car. For a smart key, that means the emergency blade hidden inside the fob; for a transponder or remote-head key, it's the main blade you'll use every day. We deburr the cuts and check the fit in each lock so nothing binds or sticks later on.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ram system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. The last step is a short walkthrough. We show you how many keys the car now recognizes, point out the dead-fob start method for your vehicle, and hand you an itemized receipt. If a spare makes sense, it's simplest to add it during this same visit while the equipment is already connected.

What affects the price of a ProMaster City key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ram ProMaster City is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Factory keys and fobs carry the manufacturer's part number and usually the highest parts cost. Quality aftermarket keys use compatible electronics at a lower price and work well on many vehicles. We tell you which options we trust for your car, and where an aftermarket version has known range or fit issues, we steer you to OEM.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ram system adds equipment time and labor to the job.
• Blade style and cutting. The blade still matters on keyless cars, because the emergency insert has to fit the door lock. Cutting by code is standard for us. Decoding a door lock when no key or code exists adds time, and so does progressing any cuts the door lock doesn't show.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Tips from a mobile locksmith

• Southern California heat is hard on keys. Fob batteries drain faster, plastic housings turn brittle, and rubber button pads crack when a key spends summer afternoons on a dashboard or in a sunny cup holder. Carry the fob with you or keep it shaded, and replace batteries before summer rather than after they fail.
• When a key's head cracks or its blade bends, replace it before it fails. A transponder chip can slip out of a split head, and a bent blade can break off inside the ignition or door lock, turning a simple key replacement into an extraction and repair job. Small symptoms are the inexpensive time to act.
• Photograph the back of your fob and any key tag that came with the car. The FCC ID, part number and key code printed there make ordering a replacement faster and more accurate. Store the photos somewhere you can reach from any device, not only on the phone that might go missing along with the keys.
• Learn your car's dead-fob start method now, in the driveway, rather than in a dark parking lot later. Depending on the make, you hold the fob against the start button or place it in a marked pocket in the console. Also find the hidden keyhole on the driver's door handle and practice using the emergency blade.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.

Proof of ownership

Making car keys is regulated work in California. Locksmiths are licensed and overseen by the Bureau of Security and Investigative Services under the Locksmith Act, Business and Professions Code section 6980 and following, and Julian's Locksmith holds company license LCO7891. Verification protects you more than anyone: a locksmith who will make a key for whoever asks will also make one for someone who wants your car. We record your name, the vehicle and its VIN on a work order, and we politely decline jobs where ownership can't be established. You can look up our license at search.dca.ca.gov.

Need a 2017 Ram ProMaster City key?

The quickest route to a working key for a 2017 Ram ProMaster City starts with a short phone call. Dial (951) 903-3193, share the VIN and where the car is parked in Southern California, and we'll tell you whether it's an on-site job, a dealer job, or a mix of both. No pressure and no surprise charges, just a straight plan.