2019 Ram 1500 Key Replacement

2019 1500 key specs

The DT Ram 1500 uses push-button start and a smart key, and supplier catalogs list one FCC ID, OHT-4882056, for the whole range. The shell hides an emergency key for the driver's door. Button counts run from three to six: lock, unlock and panic, plus remote start, power tailgate and air suspension where the truck has them. The TRX, sold from 2021 through 2024, is listed with a fob part number of its own. Because one FCC ID covers so many layouts, we match your fob's part number rather than its appearance.

What's specific to the 2019 1500

2019 was the first model year of the 1500 DT (5th generation). Early-production cars sometimes use different part numbers than later ones, so for a 2019 Ram 1500 we confirm the exact key from the VIN or the old key's FCC ID before cutting anything. It also marks a change from the previous generation: the 2018 1500 used a remote head key and a smart proximity key with push-button start, while the 2019 uses a smart proximity key with push-button start. Keys from the older car will not work in this one.

A 2019 Ram 1500 is about 7 years old now. Original fob batteries are near the end of their life at this age, so weak range or a "key not detected" message is often a battery before it is a failed fob. Cars this age are often on their second owner, which is when a single remaining key and a request for a spare tend to show up. Smart-key cars like the 2019 1500 can be targeted with relay attacks that extend the fob's signal from inside your home, so keep fobs away from exterior walls or in a signal-blocking pouch, and have any missing fob erased from the car.

Key options for the 2019 Ram 1500

• Smart proximity key (push-to-start). A smart or proximity key lets a 2019 Ram 1500 open when you touch the door handle and start with a push of a button while the fob stays in your pocket or bag. Antennas in the doors and cabin send out a low-frequency wake-up signal; the fob answers on a higher radio frequency with an encrypted reply, and the car only allows a start once it confirms the fob is inside. When the fob battery is weak, that conversation fails, which is why most designs include a backup: hold the fob against the start button or set it in a designated pocket. The owner's manual shows where, and it's worth checking before you need it.

How the Ram immobilizer works on the 1500

Ram became a stand-alone brand for the 2011 model year, separating the pickups from Dodge, and the badge now also covers the C/V cargo van, the ProMaster vans and the 2011 Dakota. The full-size pickups of 2011 and 2012 start with a Fobik, a bladeless remote that plugs into an ignition node in the dash; the node reads a Philips ID46 transponder inside the fob before the engine is allowed to run. The 2013 update kept the Fobik on most trucks but moved to a new fob family, and Keyless Enter 'n Go, with a proximity fob and a start button, was available on many higher trims. The 1500 Classic carried that Fobik all the way to 2024. The redesigned 1500 and Heavy Duty trucks of 2019 switched to push-button smart keys with Hitag AES (4A) transponders, learned by a radio-frequency hub and shielded by a security gateway at the diagnostic port. The 2011 Dakota kept a traditional cut transponder key. The vans follow Fiat practice instead: the ProMaster and ProMaster City launched with SIP22 flip keys carrying an ID46 chip, and the full-size ProMaster moved to a push-button smart key for 2022.

• The DT fob takes a CR2450 coin cell, thicker than the CR2032 used in Heavy Duty fobs of the same years.
• Air suspension and power tailgate buttons only work if the replacement fob's part number matches the truck's options.
• These trucks have a security gateway module that blocks unauthorized key programming at the OBD-II port.

Programming a 2019 1500 key

New smart keys are programmed to the truck's radio-frequency hub through the OBD-II port, but the security gateway module blocks that until the tool is authenticated online or connected behind the gateway with a bypass cable. With a working key in hand, adding a spare is straightforward. All-keys-lost is possible on many of these trucks, though some need extra work at the RF hub and a few still end with the dealer. We check coverage for your VIN before we come out.

Spare keys are routine. All-keys-lost may need gateway bypass, RF hub bench work or, in some cases, the dealer.

Lost every key to your 1500?

1. Gather your documents and the VIN. Find your registration or title and a government photo ID in the same name. Note the VIN, which is printed on the driver's side of the dashboard and usually on your insurance card. If the paperwork is locked in the car, tell us; we'll open the vehicle first and check it there.
2. Get into the vehicle without damage. Entry comes before key-making because we need access to the ignition, the OBD-II port and sometimes the documents in the glove box. We take care with weather stripping, door frames and paint, and we confirm the dash VIN matches your registration before going any further.
3. Originate a new key from the car. With no key to copy, the cuts come from the vehicle itself. We retrieve the key code through manufacturer channels where possible, or decode a door lock with a pick-decoder tool. Then we cut the blade on our code machine and confirm it turns the lock smoothly.
4. Program the key to the immobilizer. All-keys-lost programming often takes longer than adding a key, because the car has no trusted key to authorize the change. We follow the procedure your Ram 1500 requires, then confirm the engine starts and keeps running and the remote or keyless functions respond.
5. Erase missing keys and add a spare. A lost key's metal blade can still open your doors even after its chip is erased. If the keys disappeared along with something showing where you live or park, consider rekeying the car's door lock cylinders too. We'll also recommend leaving with two working keys, not one.

Why a spare key pays for itself

• A spare turns a future all-keys-lost emergency into a simple add-a-key job. With one working key in hand, programming is quicker, and the chip or fob can often be paired without decoding locks or reading modules, which keeps the cost of a lost key far lower.
• Some vehicles make it hard to add a key once you're down to one. Certain immobilizer systems let an owner program an extra key on-board only when two working keys are present, so a second key preserves the easy options for later and avoids a full reset.
• Electronics fail without warning. A fob dropped on concrete, run through the washing machine or soaked at the pool can quit for good. With a second programmed key, that's an annoyance you fix on your own schedule, not a stranded car that needs attention today.

Dealer or mobile locksmith?

Price and parts are the other half of the comparison. Dealers typically sell factory keys only and charge their posted service rates for programming. We offer factory keys where it matters and quality aftermarket alternatives where they perform well, and the quote covers cutting, programming and the trip, with nothing tacked on at the end. Timing differs too. Dealer service departments generally keep business hours, while we take automotive calls every day from 6:30 a.m. to 11:30 p.m., which covers early commutes and late evenings. We're closed overnight, and we'll be upfront if your timing means the dealer or a next-day visit is the better plan. Neither option is wrong; the right one depends on your 1500 and your schedule.

1500 key battery

Most fobs for a 2019 Ram 1500 open along a small slot in the seam; a coin or a plastic pry tool works better than a screwdriver, which chews up the housing. If the fob hides a mechanical blade, slide it out first, since the case often opens from that gap. Note which side of the old cell faces up, swap in a fresh CR2450, and press the halves together until they click all the way around. Handle the new battery by its edges, because skin oil on the faces can hurt contact. In most cases the fob keeps its programming through a battery change, so test lock, unlock and start, and you're done.

How the job works

1. Identify the exact key your 1500 uses. We ask a few quick questions on the phone: the year, whether the car starts with a turn key or a button, how many keys you have left, and whether the remote still works the doors. Then we check the VIN against our programming references so the van arrives with the correct blank or fob, not a close guess.
2. Verify ownership before any work. California holds licensed locksmiths responsible for knowing whose car they're making keys for. We record your name, the VIN and the plate on a work order. If you aren't the registered owner, you'll need the owner's written authorization along with your own photo ID before we begin.
3. Get the key code or decode the lock. A key is cut from a code, not a guess. When the factory code can be retrieved through manufacturer channels after ownership is verified, we use it. When it can't, we decode a door lock with a pick-decoder tool that reads the wafer positions without damaging anything, then work out any missing cuts.
4. Cut the blade on-site. Our van carries a code-cutting machine that handles both traditional edge-cut blades and the laser-cut, side-milled profiles common on newer keys. The blade is cut to the code, then test-fitted in a door lock and the ignition or emergency keyhole to confirm smooth operation before any programming begins.
5. Program the chip, remote or smart key. With the blade done, we connect to the OBD-II port and register the new key with the immobilizer. Depending on the Ram system, this may involve a security PIN, a timed waiting period, or on-board button sequences for the remote. On some vehicles we clone a working key's chip instead, when that's the more reliable path.
6. Test everything and clear out old keys. Before we leave, every function gets checked: doors, trunk or liftgate, panic button, remote range, engine start, and the emergency blade in the driver's door. If keys are missing, we delete them from the car's memory where the system allows, so a lost key can no longer start the engine.

What affects the price of a 1500 key

• The type of key. The biggest factor is technology. A plain mechanical key is a cutting job only. A transponder key adds a chip and programming. Remote-head and flip keys add a circuit board, and a proximity fob for a push-button Ram 1500 is the most involved of all, both in the part itself and in the programming.
• Factory or aftermarket parts. Some owners want an exact factory match; others just want a dependable key that starts the car. Both are reasonable choices. The part you pick changes the quote, so we lay out the options side by side, with the trade-offs in fit, button feel and long-term durability, before you decide.
• Programming complexity and security access. Some immobilizers accept a new key with a few on-board steps. Others need a PIN code, a timed security wait, manufacturer online access, or removing a module to read its data. Every extra layer of security on the Ram system adds equipment time and labor to the job.
• Blade style and cutting. Traditional edge-cut blades are quick to cut. High-security laser-cut blades, with a groove milled into the side, need a specialized machine and more care, and the blanks themselves cost more. If we have to decode a lock to find the cuts, that adds labor as well.

Call (951) 903-3193 with your VIN and the keys you still have, and we'll quote the job before any work starts.

Common Ram key problems

• Aftermarket remote starters are common on diesel Rams and usually rely on an immobilizer bypass module. After keys are reprogrammed, remote start may quit until the bypass is re-learned, even though the fob starts the truck normally.
• Upfitted chassis cabs and work vans carry body, toolbox and compartment locks that are separate from the vehicle key. Those can usually be rekeyed or replaced on their own when a key ring goes missing from a fleet.
• The Fobik ignition node on 2011-2018 Rams and the 1500 Classic can stop reading the fob, refuse to turn, or trap the fob in the dash. We test the node first, because a new fob will not fix a failing reader.

Tips from a mobile locksmith

• Every so often, use the mechanical blade in the driver's door lock. Cylinders that go years without a key can seize from dust and dried grease, and you won't find out until the day the fob dies and the blade is your only way in. A small shot of dry lubricant keeps the lock ready.
• On any vehicle with a turn-key ignition, keep the key ring light. A heavy cluster of keys, tools and charms swings with every bump and slowly wears the ignition wafers and the key itself. When the key starts to stick or needs a wiggle to turn, deal with it early, before it stops turning entirely.
• Make the spare before you need it. Adding a key while one still works is quicker and less expensive than starting from nothing, and it keeps the simpler programming options available. Good moments are right after buying the car, or as soon as one of your two keys goes missing.

Proof of ownership

Before we cut or program a key for any vehicle, we verify that you have the right to it. Please have two things ready: the current registration or the title, and a government-issued photo ID with a matching name. We also check that the VIN on those documents matches the VIN plate on the dashboard. If the registration is locked inside the car, that's fine; we open the vehicle first, check the paperwork in the glove box, and only then make the key. If something doesn't line up, we stop and sort it out before any key is made.

Need a 2019 Ram 1500 key?

Need a key for your 2019 Ram 1500? Call Julian's Locksmith at (951) 903-3193 with your VIN and tell us which keys you still have. We'll confirm what the job involves, give you a quote before any work starts, and come to you in Southern California with everything needed to cut and program the key on the spot.